PYLE PLBT71G (01) PDF Document

To enjoy the unit’s features, along with proper and safe operation, please be sure to read through this manual before use. It is especially important to thoroughly understand and follow all system warnings and precautions. Keep the manual in a safe location for future reference when necessary.

Contact your dealer or the nearest authorized repair center for any service, repair or technical support assistance.

Factory batteries are sometimes depleted from extended storage time, so replace them if the unit does not respond to the remote. Also note that Pyle Receiver Remotes are universal and used between multiple radio models, which may or may not, have some buttons / functions that do not work or provide other functionality with your receiver headunit. If some functions respond your remote is not defective.

Clean the LCD with a slightly damp cloth. Keep the screen clean and free of any debris.

Do not use solvents such as alcohol, benzene, thinner, commercially available cleaners or antistatic spray. When wiping the screen be sure not to scratch the surface.

In cold weather, check for condensation on the disc. If found, wipe the moisture from the disc and do not operate your player for an hour until condensation disappears from the unit’s optical reader.

The screen may not be clear if the temperature of the vehicle is too cold or too hot. The picture will return as the car’s temperature returns to normal. Never touch the screen, or operate the touch screen, with anything besides your finger(s). When the display is subject to direct sunlight and glare, the unit may become hot resulting in possible damage to the LCD display. Avoid exposing the display to excessive sunlight as much as possible.

In the event of a malfunction, never open the unit’s casing or lubricate any parts. Contact Sound Around USA for repair information.

If liquid or any other foreign substances enter the unit, turn the power off immediately and consult your dealer or the nearest authorized repair center. If you notice smoke, irregular noises or smells coming from the unit, power off immediately and consult your dealer or the nearest authorized repair center. Do not attempt to disassemble or modify the unit as there are sensitive and high voltage electronic components which can cause damage to the unit, or to one’s self, if handled improperly. Be sure to consult your dealer or the nearest authorized repair center for any technical assistance.

The button layout and functions are as follows:

The front panel button and feature layout for the PYLE PLBT71G is as follows:

1) Turn on the engine key to the “ACC” or “ON” position

2) Press and hold the power button for 3 seconds

-When the engine key is turned to the off position the unit is turned off

The Status Bar items are:

1) Home Icon – Switch between “app screen” and “radio interface”

2) Moon and star Icon – Turn off display (Awaken by tapping screen)

3) Time display

4) Current volume setting

5) Media status icons (Illuminate to show media is available)

The main applications/sources are:

Swipe left/right to access more apps.

For Settings:

1) Scrolling: Use the red bar to scroll through the list of all available options.

2) Turn on/off: Many settings can be toggled on or off in this screen

*Note: Factory setup is not adjustable by user. Do not attempt to enter this setup menu.

For Set Time:

1) Time Options: Turn GPS auto update and 12 hour clock settings on and off here.

2) Date and Time: Use the up and down arrows to set the date and time accordingly.

For Sound Fade/Balance:

Hold and drag left, right up or down to control the fade and balance of your audio output.

Auxiliary input (rear RCA jacks) allow audio and video from external devices to be displayed or played through the unit. Auxiliary output (rear RCA jacks) allow audio and video to be sent out to external devices.

1) Customization – Use the settings to adjust and optimize the display quality.

Note: auxiliary app will display “No Signal” if no video signal is connected. Screen controls will not become active until external video signal is detected.

*The Parking brake will need to be wired to a grounding trigger to allow video pass through or a warning message will appear saying warning video disabled while driving.

The Calendar displays the day, month and year.

Use forward and back arrows the view past or future months. Selected dates are highlighted in blue.

Note: Calendar does not allow entry of appointments. Date must be set within system settings.

The Calculator is a handy little app for simple calculations.

For EQ – Equalizer:

Presets: Select one to automatically adjust the equalizer.

Adjustments: Hold and drag up or down to manually adjust the EQ by each frequency band.

For Radio operation on the PYLE PLBT71G:

1) Scanning: Press, hold, and drag the slider to quickly tune the radio.

2) Current Station: The currently selected station will be displayed in the center. Press the forward and back arrows to change the current station.

3) Favorite Stations: Press and hold one of the six preset slots to set and save a selection for later.

Warning: Do not attempt to browse files while operating the vehicle.

For Browsing Files:

File location is displayed.

Use “Back Arrow” to return to the previous folder.

For Selecting Files:

The files and folders of your storage media are displayed. Once the desired folder is located, select it and press “check icon” to open.

Plug in flash drives to access music video and photos.

For Video settings:

1) Brightness, Contrast, Hue: Press, hold and drag to adjust the brightness, contrast and hue of the display.

2) Presets: Select to automatically adjust the display settings.

Note: Wallpapers can be imported from a flash drive or SD card. Check format sheet online for specs on formats.

1) Browse – Use left and right arrows to select the desired wallpaper.

2) Select – Press OK to select the wallpaper.

For Installing Steering Wheel Control:

Key 1 and Key 2 wires are used for setting up steering wheel controls. The location of the attachment wires in the steering wheel column varies between different vehicle makes and models.

For Steering Wheel Controls:

Select the command in the application, then press the corresponding button on the wheel to teach the unit how to behave when steering wheel controls are used. To enter the steering wheel menu it will prompt you for a 4 digit pass code you will need to enter ‘0000’. Then you can manually program each desired option following the on screen instructions. (Note: This feature is not compatible with all vehicle types).

Use a multi-meter to check for 12v+ to red and yellow wires. Check for proper Ground on the Black wire.

Attach “PARK” wire to parking break. When this wire is grounded the video will play (Grounding trigger of the parking brake).

Attach “BACK” wire to reverse tail light 12v+. Make sure camera is and sending video signal.

Check that yellow memory wire is attached to 12v+ constant.

Turn off GPS auto update by going to radio settings > Set Time > switch off auto update.

Check antenna is connected properly.

Mount Antenna directly to your vehicle (GPS antenna is to be magnetically mounted, it will boost GPS reception when attached).

Check alternate antenna placement to test for interference.

Change GPS sound settings by going to Navi > Settings > Sounds > Set GPS voice level to max > Set radio volume to min (Adjust accordingly).

The radio will notify you when a map update becomes available. You will need to send out a new map card from our parts department.

This unit’s hardware does not allow it to be updated with new OS or firmware.

This device is not capable of receiving internet data.

(Traffic and weather feature only available in Europe).

-Check that nothing is covering microphone port.

-Check to see if closer proximity to the mic affects its pickup.

-Check that phone connection is good.

-Make sure the call recipient has speaker volume set to an appropriate level.

-Check that the mic is not picking up too much background noise.

Note: The built-in mic cannot be changed, replaced or upgraded.

Check that your device is Bluetooth compatible 4.0+.

Check if you are able to pair with alternate devices via Bluetooth.

Clear out your device history in your Bluetooth setting menu and attempt to pair / connect again.

This is caused by bug in map software.

You may be able to fix the software on your own by performing these steps:

– Insert GPS card into computer.

Open text file under Primo\save\profiles\01\system.ini.

Edit the file to return the cockpit type to “1”.

* Deleting the profile folder will default the unit’s settings back to cockpit number 1.

Make sure SD card is compatible.

Check file format of your file (You may need to convert your video file to an alternate file format).

Your unit requires touchscreen calibration. You have entered the ‘Touch Screen Calibration Menu’. For optimum touchscreen performance, this feature enables you to enjoy the best functionality of your device’s touch screen. To complete the touchscreen calibration, an “X” will appear in the circles on the screen in numbered order, continue to press the center of the “X” as it passes through each numbered circle.

(In circle number one, you will see an “X”, touch the center of the “X”, then the “X” will move to circle number two. Continue to touch the center of the “X” as it will move to the other circles in numbered order. If calibration senses an error, the process may restart; Repeat if necessary.)

Press and drag along the time line to quickly skip through DVD times line. (Note: DVD formatting does not allow scrubbing through previews and warnings).

The menu options and controls are:

To pair your phone, ensure Bluetooth is enabled in your phone’s system settings and that you are disconnected from all other devices.

In the Bluetooth app of your radio, press the “Gear” icon in the left column to access Bluetooth settings. Next, press the “Magnifying glass” icon to set the radio into pair mode. The radio will then display “searching” and show all nearby compatible Bluetooth devices:

– Select your phone from the list, and tap a second time to initiate pairing.

– Your phone should now display a pin pad where you will enter “0000”.

– Check that device named “CAR_KITT” shows as connected on your phone.

Note: Once your phone is paired, you can use the other functions within the radio’s Bluetooth app.

The left hand column icons functions are:

– Select the “Keypad” icon to dial out using the radio’s number pad.

– Select the “address book” icon to display your phone’s contact list. You will need to import your contact list using the “download” icon located in the right column of the Bluetooth app.

– Select the “phone” icon to see a log of incoming and outgoing calls.

– Select the “gear” icon for phone pairing and selection options.

– Select the “headphones” icon for music playback controls.

The right hand column functions are:

– “Trash” delete currently selected entry.

– “Download” Use to download contact data to address book.

– “Speaker selection” Switch between car speaker/mic and phone speaker/mic.