PRO-JECT DEBUT RECORDMASTER II (01) PDF Document

The controls, features, and connections are as follows:

1. Motor with TPE damped flange

2. Stepped drive pulley

3. Drive belt

4. Sub-platter

5. Platter and felt mat

6. Tonearm counterweight

6a. Downforce scale

7. Tonearm lift lever

8. Tonearm rest and removable transport lock

9. Tonearm tube

9a. Tonearm base

10. Lid

11. Lid hinges

12. Hinge fasteners

13. USB output socket

14. RCA output socket with earth connection

15. Anti-skating weight

16. Anti-skating weight support hoop

17. Anti-skating weight adjustment scale

18. Feet with TPE damping

19. Speed selector

20. Headshell with finger lift and fitted Ortofon OM 5E

21. Single adapter

22. Switch between Phono / Line RCA output

23. Power supply socket

The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug is easily accessible at all times. Hold the plug when unplugging the power cord. Never handle the power cord while your hands are wet or damp.

Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on or near the device. Never spill any liquid on the device. Never place any naked flame sources, like lighted candles, on or near the device.

The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any other similar conditions.

Keep plastic bags away from children to prevent any risk of suffocation.

The deck is supplied partially disassembled and carefully packaged for safe transport. Carefully remove all parts from the transport packaging.

Make sure the surface you wish to use the turntable on is level (use a spirit level) before placing the turntable on it.

Remove the transport lock from the tonearm. Store it in the original packaging so it is available for any future transportation.

Fit the drive belt around the hub and the smaller diameter part of the motor pulley. Avoid getting sweat or grease on the belt as these will deteriorate the performance and reduce the belt’s lifespan. Use absorbent kitchen paper to remove any oil or grease from the outer edge of the hub and the belt.

Fit the platter and felt mat over the spindle of the hub.

The counterweight supplied is suitable for cartridges weighing between 3.5 – 5.5g (Ortofon OM 5e – weight no. 00).

Pushing carefully, turn the counterweight onto the rear end of the tonearm tube, so that the downforce scale shows towards the front of the player.

Lower the armlift and position the cartridge in the space between arm rest and platter. Carefully rotate the counterweight until the armtube balances out. The arm should return to the balanced position if it is moved up or down. This adjustment must be done carefully. Do not forget to remove the cartridge protection cap if fitted.

Once the arm is correctly balanced return it to the rest. Hold the counterweight without moving it, and gently revolve the downforce scale ring until the zero is in line with the anti-skating prong. Check whether the arm still balances out.

Rotate the counterweight counter clockwise (seen from the front) to adjust the downforce according to the cartridge manufacturer’s recommendations. One mark on the scale represents 1 mN (= 0.1g / 0.1 Pond) of downforce.

Please note: Adjust the downforce prior to installing the anti-skating weight. The recommended downforce for the Ortofon OM 5E cartridge is 17.5mN.

The anti-skating force must be adjusted corresponding to the downforce as follows:

Slip the loop of the anti-skating weight’s thread over the second groove of the stub to set the correct anti-skating force for the factory-fitted cartridge. Feed the thread through the loop of the wire support.

The record player has gold plated female RCA phono sockets and possibility to choose between Phono and LINE output.

With LINE OUT on, you can use a line input (such as AUX, CD, Tuner, Tape or Video) on your amplifier.

With PHONO OUT on, you can use your own phono pre-amplifier (sometimes labelled gram, disc or RIAA).

Take care to connect the left and right channels correctly. The right channel is usually marked red, the left channel black or white.

The earthing wire of the tonearm lead should be connected to the earth terminal on your amplifier (if provided).

Connect the USB-output of the unit to a free USB-socket on your computer and turn it on/make sure it is powered on. The “new hardware found assistant” will automatically detect the unit and announces it as a Microphone USB audio codec. There is no need to install a driver manually.

After installation, one setting has to be done. For example – Windows 7 operating system:

Control Panel > Sound > Recording > Microphone USB Audio CODEC > Properties > Advanced: set to 2 channel, 16 bit, 48000 Hz (DVD Quality).

Please note: Connection should be made to an USB-socket of your computer directly. Connecting to USB-hubs or switches can cause problems.

In case you do not have a recording programme installed on your computer, you may download one free from the Internet. Recording programmes may be found by searching Google.

In the menu of the recording programme, source or input may have to be set to Microphone USB audio codec.

Please be aware that downloads from the Internet are made entirely at your own risk.

The turntable is supplied with the universal power supply with 3 exchangeable sockets adapters suitable for all countries. Select the correct adapter for your country and insert the adapter to the exchangeable part of the power supply.

Connect the low voltage plug from the power supply to the socket (14) on the rear of the record player before connecting the power supply to the mains.

Fit the lid (dust cover 10) carefully over the hinge prongs and adjust the screws (12) until the lid stays open where you want it to without being too stiff to open or close.

The turntable is equipped with a three-position switch for ON/OFF and electronic speed change.

To play records at 33 r.p.m. press this switch (19) to the left side.

To play records at 45 r.p.m. press this switch (19) to the right side.

To be able to play 78 r.p.m. the flat drive belt has to be removed and the round drive belt has to be fitted around the sub-platter (4) and the larger diameter part of the motor pulley (2). To do so, the platter (5) has to be removed.

After the round drive belt has been fitted, pressing the ON/OFF switch to the right selects 78 r.p.m.

The record player should be positioned on a low-resonance surface such as wood or multiple layer ply board to avoid structural vibrations disturbing replay.

The cartridge needle must be vertical in the record groove in order to trace the groove wall modulations correctly. A small screw at the bearing end of the arm allows incorrect azimuth to be corrected if your needle is not mounted exactly perpendicular to the cartridge body (which is often the case).

Slacken off the screw just enough to be able to revolve the arm tube without applying force. Please note: do not remove the screw completely!

With the aid of a good magnifying glass adjust the needle until it is vertical in the groove (i.e. perpendicular to the record’s surface). Ideally this should correspond to the top surface of the cartridge body being parallel to the record surface.

When you are satisfied that the needle is vertical retighten the screw carefully.

Please note: Under no circumstances should the arm tube be adjusted with the needle still in the record groove! Irreparable damage may be caused to the cantilever suspension! The arm must be lifted to make each adjustment and lowered afterwards to check it.

All cartridges with half inch mounting holes can be fitted. Leaving the needle’s protection cover on, fit the cartridge to the headshell using the screws supplied with the cartridge by passing one screw through each slot in the headshell. Do not tighten the nuts yet.

Connect the tonearm wires to the cartridge pins as follows:

white: left channel positive (L+)

red: right channel pos. (R+)

green: right channel return (R -)

blue: left channel return (L -)

The full sound quality of the record player can only be achieved if the cartridge is correctly adjusted. Particular tools like the alignment tool are required to accomplish this job properly.

If you are not well acquainted with the adjustment of cartridges you are advised to call upon the willing help of your dealer to accomplish this task for you.

Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic cloth. Never use a dry cloth because this will create static electricity which attract more dust! Antistatic cleaning fluids are available at specialist stores but must be applied sparingly to avoid damage to rubber parts.

It is recommended to fit the needle cover before cleaning or maintenance is carried out to avoid damage.

If the player is not used over a long period of time the drive belt can be removed to prevent unequal stretching.

Always disconnect the record player from the mains power supply as a precaution before maintenance!

Nominal speeds: 33/45 r.p.m. (78 r.p.m. optional)

Speed variance: 33: +/-0.70%; 45: +/-0.60%

Wow and flutter: 33: +/-0.19%; 45: +/-0.17%

Signal to noise: 68dB

Effective tonearm mass: 8g

Effective tonearm length: 8.6 ” ( 218.5mm)

Overhang: 18.5mm

Power consumption: 4W/0W in Stand-By

Outboard power supply: 15V / 0 – 0.8mA DC (set at 0.5mA), universal power supply

Dimensions (W x H x D): 415 x 118 x 320mm, dust cover open 415 x 365 x 405mm

Weight: 5.6kg

Dimensions packaging (W x H x D): 488 x 235 x 393mm

Weight incl. packaging: 8.0kg

Frequency range: 20-22.000Hz

Channel separation: 22dB/1kHz

Output voltage: 4mV

Recommended load impedance: 47kohms/amplifier connection – MM-input

Compliance/stylus type: 20µm/mN – elliptical

Recommended tracking force: 17.5mN

Weight: 5g

Gain: 34dB

Output voltage typically: 200mV/1kHz at 5mV/1kHz input

Input impedance: 47kohms/100pF

Noise floor: -68dB

RIAA-equalisation curve accuracy: 20Hz-20kHz / max. 0,5dB

The platter doesn’t turn although the unit is switched on:

The unit is not connected to the mains power supply.

No mains at the socket.

Drive belt is not fitted or has slipped off.

No signal through one or other channel or both channels:

No signal contact from the cartridge to the internal tonearm wiring or from that to the arm lead or from that to the phono box or between that and the amplifier. This could be due to a faulty plug, broken wire or solder joint or simply loose plug/socket connection.

Phono input not selected at amplifier.

Amplifier not switched on.

Amplifier or speakers defective or muted.

No connection to the loudspeakers.

Strong hum on phono input:

No earth connection from cartridge or arm or arm cable to amplifier, or earth loop.

Distorted or inconsistent sound from one or both channels:

Record player is connected to wrong input of amplifier, or MM/MC switch incorrectly set.

Needle or cantilever damaged.

Wrong r.p.m., drive belt overstretched or dirty, platter bearing without oil, dirty or damaged.