Free English PHILIPS DYNALITE DMR310 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PHILIPS DYNALITE DMR310 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the installation requirements for the PHILIPS DYNALITE DMR310?
The PHILIPS DYNALITE DMR310 devices must be installed by a qualified electrician in accordance with all national and local electrical and construction codes and regulations.
What is the IEC Pollution Degree for the PHILIPS DYNALITE DMR310?
The IEC Pollution Degree for the PHILIPS DYNALITE DMR310 is Degree II.
What is the operating temperature range for the PHILIPS DYNALITE DMR310?
The operating temperature range for the PHILIPS DYNALITE DMR310 is between 0° C (32° F) and 40° C (104° F), with a maximum relative humidity of ≤90%.
What is the mounting torque specification for the circuit breaker connection on the PHILIPS DYNALITE DMR310?
Refer to the circuit breaker for the torque rating when connecting to the PHILIPS DYNALITE DMR310.
What are the Output Ratings per Channel (CH) for the PHILIPS DYNALITE DMR310?
The Output Ratings per Channel (CH) for the PHILIPS DYNALITE DMR310 are as follows:
| Load Type | DMR310 CH1-CH3 |
|---|---|
| Incandescent | 10 A, 277 V~ |
| Magnetic with Halogen | 10 A, 277 V~ |
| Electronic Driver | 10 A, 277 V ~ |
| Motor | 9.8 FLA (1/2 HP), 120 V ~ |
| Motor | 10 FLA (1 1/2 HP), 230/277V ~ |
| Inrush Current | 500 A |
What is the maximum Output Rating per Group for the PHILIPS DYNALITE DMR310?
The maximum Output Rating per Group for the PHILIPS DYNALITE DMR310 is ≤ 30 A.
What is the recommended wire size and associated torque for the load connections on the PHILIPS DYNALITE DMR310?
For load connections on the PHILIPS DYNALITE DMR310, use wire sizes up to ≤ 16 mm² (6+ AWG), and apply a torque of 1.5 Nm (13.3 Lb-in).
What are the voltage and current specifications for the single-phase input of the PHILIPS DYNALITE DMR310?
For single-phase input (1~) on the PHILIPS DYNALITE DMR310, the specification is 120/230/277V~ ± 10% 30 A.
What are the voltage and current specifications for the three-phase input of the PHILIPS DYNALITE DMR310?
For three-phase input (3~) on the PHILIPS DYNALITE DMR310, the specification is 120/230/277V ~ ± 10% 3 x 10 A.
What is the IEC Overvoltage Category for the PHILIPS DYNALITE DMR310?
The IEC Overvoltage Category for the PHILIPS DYNALITE DMR310 is Category III.
How are the relay channels wired for the PHILIPS DYNALITE DMR310?
The wiring for the PHILIPS DYNALITE DMR310 relay channels involves connecting the Neutral lines (N-1, N-2, N-3) and Line outputs (L OUT-1, L OUT-2, L OUT-3) to the respective loads. The internal connection diagram shows the relay contacts switching the Line inputs (L1, L2, L3) to the corresponding outputs (L OUT-1, L OUT-2, L OUT-3) when actuated.
CLICK HERE TO DOWNLOAD PHILIPS DYNALITE DMR310 (01) PDF DOCUMENT