PHILIPS DYNALITE DDLEDC605GL (01) PDF Document

The PHILIPS DYNALITE DDLEDC605GL must be installed in an approved enclosure by a qualified electrician. The installation must be in accordance with all national and local electrical and construction codes and regulations.

The PHILIPS DYNALITE DDLEDC605GL is designed to be mounted on a standard DIN rail within an approved enclosure.

The dimensions and required clearances for the device are as follows:

Dimensions:

Height: 95 mm (3.74 in)

Width: 105 mm (4.13 in)

Depth: 75 mm (2.95 in)

Clearances:

A minimum clearance of 45 mm (1.77 in) is required above and below the device for ventilation.

The PHILIPS DYNALITE DDLEDC605GL is rated for the following environmental conditions:

Operating Temperature: 0°C (32°F) to 40°C (104°F)

Humidity: ≤ 90%

Pollution Rating: IEC Pollution Degree II

Safety Rating: IEC Overvoltage Category III

The PHILIPS DYNALITE DDLEDC605GL requires a Class 1 or Class 2 (UL) / SELV (CE and RCM) power supply with the following specifications:

Voltage: 10-24 V DC

Voltage Ripple: ± 2% ≤ 1 Vpp

Maximum Current: ≤ 20 A

The PHILIPS DYNALITE DDLEDC605GL has 6 output channels, each with the following specifications:

Current Range per Channel: 10 mA – 5 A

Mode: Voltage Mode

Connect the positive terminal (A+) of your LED load to the corresponding channel’s ‘A’ terminal and the negative terminal (K-) to the ‘K’ terminal. The wiring classification depends on the power supply used:

• To be wired as Class 1 when powered by a Class 1 power supply.

• To be wired as Class 2 when powered by a Class 2 power supply.

Wire size: ≤ 2.5 mm² (12+ AWG)

Terminal torque: 0.4 Nm (3.5 Lb-in)

Maximum wire length:

• ≤ 20 m at 24 V

• ≤ 10 m at 12 V

For a single power supply configuration, bridge the two positive inputs (+V1 and +V2) and connect the single positive wire from your power supply. Connect the negative wire to the -COM terminal. The total load must not exceed 20 A.

Power input wire size: ≤ 5 mm² (10+ AWG)

Power input terminal torque: 0.6 Nm (5.5 Lb-in)

Maximum wire length from power supply:

• ≤ 2 m at 24 V

• ≤ 1 m at 12 V

For a dual power supply configuration, connect one power supply to the +V1 and -COM terminals (for channels 1-3) and the second power supply to the +V2 and -COM terminals (for channels 4-6). The negative -COM terminals must be common.

Important constraints:

• The load on each power supply input (+V1 or +V2) must not exceed 15 A.

• The total combined current for both inputs must not exceed 20 A (*V2 + *V1 ≤ 20 A).

Maximum wire length from power supply:

• ≤ 2 m at 24 V

• ≤ 1 m at 12 V

You can connect to a control network using either the screw terminals or the RJ12 port.

Using Screw Terminals (RS-485 DyNet):

Connect the network cable to the green terminal block with the following connections: SHLD (Shield), GND (Ground), D+ (Data+), D- (Data-).

• Wire size: 0.3 – 2.5 mm² (22-12 AWG)

• Terminal torque: 0.4 Nm (3.5 Lb-in)

Using RJ12 Port (RS-485 DyNet / DMX RX):

Plug an RJ12 cable into the port. The pinout is as follows:

1: GND

2: GND

3: D+

4: D-

5: +12 V

6: +12 V

To set the DMX 512 start address, use the 10-position DIP switch on the front of the device. Each switch corresponds to a value (1, 2, 4, 8, 16, 32, 64, 128, 256, and X for the 10th switch). Set the switches to the ON position to sum their values to the desired DMX start address. For example, to set address 3, turn switches 1 (value 1) and 2 (value 2) to ON.

If the PHILIPS DYNALITE DDLEDC605GL causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Any modifications not approved by the manufacturer of this device could void the user’s authority to operate this device.