OMEGA OCI604TCOM (01) PDF MANUAL

OMEGA OCI604TCOM (01) PDF SUMMARY:

How should the Induction Cooktop be installed?

The cooktop must only be installed in accordance with the instructions provided. Incorrect installation may cause harm to persons, damage property, and void the product’s warranty. The appliance should be connected to a circuit with an isolating switch for full disconnection from the power supply. All cabinetry and materials must withstand a minimum temperature of 50°C above the room’s ambient temperature while in use. A barrier must be installed to prevent accidental contact with the cooktop base where it is accessible. A minimum clearance of 50mm must be maintained between the base and the barrier. Do not use any kind of silicon sealant to seal the appliance against the benchtop. Clamps and screws are supplied to ensure the cooktop cannot move after installation.

---

What are the cut-out dimensions for the 30cm and 60cm cooktops?

For the OCI302TCOM model, the width is 268mm and the depth is 500mm. For the OCI604TCOM model, the width is 560mm and the depth is 490mm. A minimum of 50mm clearance space around the cut-out must be met when installing the appliance. The thickness of the work surface should be at least 30mm.

---

What should I ensure regarding ventilation during installation?

Ensure the cooktop is well-ventilated and the air inlet and outlet are not blocked. Ensure adequate airflow from outside the cabinetry to the base of the cooktop.

---

What minimum clearances should be observed for combustible surfaces?

Always ensure the appliance is installed in accordance with AS/NZS 5601.1, or AS/NZS 5601.2 regarding clearances to combustible surfaces and materials, and clearances to rangehoods and exhaust fans. Refer to your rangehood’s user manual for the exact minimum clearances from the top of the cooktop surface to your rangehood.

---

How do I apply the fixing brackets?

Place the unit on a stable, smooth surface. Fix the cooktop on the work surface by screwing in the four brackets on the bottom of the cooktop after installation. Adjust the brackets’ position to suit your work surface’s thickness. The brackets should not touch the inner surfaces of the worktop after installation.

---

How should the electrical connection be made?

If the cooktop doesn’t come with a 10 amp power plug, the power supply should be connected in compliance with the relevant standard, or a single-pole circuit breaker. If the cable is damaged or needs replacing, this should be done by an after-sales technician using the proper tools. If the appliance is being connected directly to the mains supply, an omnipolar circuit breaker must be installed with a minimum gap of 3mm between the contacts. The installer must ensure that the correct electrical connection has been made and that it complies with safety regulations. The cable must not be bent or compressed. The cable must be checked regularly and only replaced by a proper qualified person.

---

How do I power on the OCI302TCOM cooktop?

Touch the ON/OFF symbol for 3 seconds to activate the cooktop.

---

How do I prepare the cooking surface?

Place an induction-compatible pan or pot on the desired cooking zone. Ensure both the bottom of the pan and the cooktop’s surface are clean and dry for optimal cooking performance.

---

How do I select the cooking zone and heat setting on the OCI302TCOM?

Press the cooking zone selection button on the control panel to activate it. The cooking zone display flashes “-” for the selected cooking zone. Set the desired power level by pressing the power control button to 1 to 9.

---

What does the “U” symbol indicate on the OCI302TCOM control panel?

The “U” symbol indicates that the cookware’s bottom diameter is too small or it is made of an unsuitable material for induction cooking. Check the cookware bottom to ensure it is suitable for induction cooking.

---

How do I power on the OCI604TCOM cooktop?

Touch the ON/OFF control. After power on, the buzzer beeps once, and all displays show “–” or “– –”, indicating that the induction cooktop has entered the state of standby mode.

---

How do I select the cooking zone and heat setting on the OCI604TCOM?

Press the cooking zone selection button on the control panel to activate it. An indicator next to the key will flash. Select a heat setting by touching the slider control.

---

How do I switch off individual cooking zones on the OCI302TCOM?

Press the cooking zone selection symbol to activate it (the number of the selected zone flashes). Press the power control button to gradually adjust the power to 0.

---

How do I turn off the entire OCI302TCOM cooktop?

By pressing the ON/OFF button, you can turn off the induction cooktop. All the settings will be reset.

---

What does the “H” display after cooking indicate?

“H” may display, indicating that the cooking zone is too hot to touch. This symbol will disappear once the surface has cooled to a safe temperature. You can use the residual heat to further heat other pans or continue cooking without additional power usage.

---

How do I switch off individual cooking zones on the OCI604TCOM?

Touch the heating zone selection control that you wish to switch off. Turn the cooking zone off by touching the slider to “|”. Make sure the display shows “0”.

---

How do I turn off the entire OCI604TCOM cooktop?

Turn the whole cooktop off by touching the ON/OFF control.

---

How do I activate the Boost function on the OCI302TCOM?

Press the cooking zone selection button to activate it (the digit of the selected zone flashes). Then press and hold the Power Boost button key until the power level display shows “P”, which signals that the selected cooking zone is set to maximum power.

---

How do I cancel the Boost function on the OCI302TCOM?

Press the zone selection button to select the zone for which you want to disable this function. Then press the button Power Boost button key. The cooking zone will be set to the power level it was set before activating the Power Boost function. The ‘b’ icon will disappear from the display.

---

How do I activate the Boost function on the OCI604TCOM?

Touch the heating zone selection control. Touch the power boost control, the zone indicator show “P” which signals that the selected cooking zone is set to maximum power.

---

How do I cancel the Boost function on the OCI604TCOM?

Touch the heating zone selection control that you wish to cancel the boost function. Touch the “Boost” control to cancel the Boost function, then the cooking zone will revert to its original setting.

---

How do I use the Timer as a Minute Minder on the OCI302TCOM?

While cooking, press the to set the timer (1). The number “10” will be displayed and will start to flash. Set the time by pressing the “-” or “+” button. After this time, the set cooking time begins to count down.

---

How do I use the Timer as a Minute Minder on the OCI604TCOM?

Touch the Timer Adjustment / Selector control, the “10” will show in the timer display. and the “0” flashes. Set the time by touching the slider control. Touch timer control again, the “1” will flash. Set the time by touching the slider control, now the timer is set.

---

How do I use the timer to power off one or more cooking zones on the OCI604TCOM?

Touching the heating zone selection control that you want to set the timer for, the “10” will show in the timer display and the “0” flashes. Set the time by touching the slider control. Touch timer control again, the “1” will flash. Set the time by touching the slider control, now the timer is set. When the cooking timer expires, the corresponding cooking zone will be switched off automatically.

---

How do I cancel the Timer on the OCI604TCOM?

Select the heating zone for which you want to cancel the timer. Touching the timer control, the indicator flash. Touch the slider control to set the timer to “00”, the timer is cancelled.

---

How do I use the Child Lock Function on the OCI302TCOM?

To lock the control panel, press and hold the power boost and timer buttons for a few seconds. The “Lo” (Lock) symbol will be displayed on the control panel, which symbolizes that the control panel is locked. To unlock the controls, press and hold the symbol for activation/deactivation of the child lock (power boost and timer buttons) until the acoustic sound goes off. The “Lo” symbol disappears and the control panel is active again.

---

How do I use the Child Lock Function on the OCI604TCOM?

To lock the controls, touch the lock control. The timer indicator will show “ Lo“. To lock the controls, touch and hold the lock control for a while.

---

How do I use the FlexZones on the OCI302TCOM as a single large zone?

Press the FlexZone button to merge the bridge area into a single large zone. An alert will sound, indicating the cooktop has entered FlexZone selection, and the corresponding indicator will display flashing. Set the desired power level by touch and pressing the Power Level Adjustment Controls.

---

How do I cancel Flexible Zone Function on the OCI302TCOM?

Touch any of the Zone Selector buttons that are in use to deactivate the FlexZone function. The power settings will operate as usual for a standard cooking area.

---

How do I use the Start / Pause function on the OCI302TCOM?

Press the Start / Pause button. All heating zones will cease operation, displaying “ | | ” on the zone indicators. Touch any of the Zone Selector buttons first, followed by pressing the Start / Pause button again to deactivate Pause. All cooking zones will then return to their initial settings.

---

What should I do in case of everyday soiling on the glass?

Switch the power to the cooktop off. Apply a cooktop cleaner while the glass is still warm (but not hot!). Rinse and wipe dry with a clean cloth or paper towel. Switch the power to the cooktop back on.

---

What should I do in case of boilovers, melts, and hot sugary spills on the cooktop glass?

Remove these immediately with a fish slice, palette knife, or razor blade scraper suitable for ceramic glass cooktops, but beware of hot cooking zone surfaces. Switch the power to the cooktop off at the wall. Hold the blade or utensil at a 30° angle and scrape the soiling or spill to a cool area of the cooktop. Clean the soiling or spill up with a dishcloth or paper towel. Follow the steps for everyday soiling on glass.

---

What should I do in case of spillovers on the touch controls?

Switch the power to the cooktop off. Soak up the spill. Wipe the touch control area with a clean damp sponge or cloth. Wipe the area completely dry with a paper towel. Switch the power to the cooktop back on.

---

What do I do if the cooktop cannot be powered on?

Ensure the cooker is connected to the power and switched on. Check if there is a power outage. If the problem persists, contact the Support Team for guidance.

---

What do I do if the touch controls won’t respond or are difficult to operate?

Deactivate the Child Lock function. Gently clean and dry the controls if there is a slight film of water. Make sure to use the pad of your finger rather than the tip when touching controls.

---

What do I do if the ceramic glass is being scratched?

Use cookware with flat and smooth bases. Avoid unsuitable cleaning products such as an abrasive scourer. See Care & Maintenance section.

---

What does it mean if the induction cooktop makes a low humming noise when used on a high heat setting?

This is caused by the technology of induction cooking. This is normal, but the noise should quieten down or disappear completely when you decrease the heat setting.

---

What does it mean if I hear fan noise coming from the cooktop?

A cooling fan built into your induction cooktop has come on to prevent the electronics from overheating. This is normal and needs no action. Do not switch the power to the induction cooktop off at the wall while the fan is running.

---

What do I do if pans do not become hot and appears in the display?

Use cookware suitable for induction cooking. Center the pan and make sure that its base matches the size of the cooking zone.

---

What do I do if the induction cooktop or a cooking zone has turned itself off unexpectedly, a tone sounds, and an error code is displayed?

Note down the fault code, switch the power to the cooktop off at the wall, and contact After Sales Support by calling 1300 11 4357 or emailing support@residentiagroup.com.au.