OMEGA M1220 (01) PDF MANUAL

OMEGA M1220 (01) PDF SUMMARY:

What are some important safeguards to follow when using the mixer?

Read all instructions before using the mixer. Plug into a grounded 3 prong outlet. Do not remove ground plug. Do not use an adapter. Do not use an extension cord. Disconnect power before cleaning or servicing, and before installing or removing agitator. Do not spray or submerge mixer. Always use a metal container when mixing. Do not put spoon or other utensils in metal container when mixing. Do not allow agitator to hit container sides when mixing. Inspect mixer and agitator daily. Replace agitators every 90 days. Do not operate any appliance with a damaged cord or plug, or after the appliance malfunctions or is damaged in any manner.

How do I connect the mixer to the main power supply?

The electrical safety of this drink mixing machine can only be achieved if the machine is properly connected to an appropriate grounded receptacle that is in compliance with current national safety standards. The manufacturer cannot be held responsible for damage and/or injury caused by failure to connect the unit to an appropriate power source. For a safe and correct installation, connect the unit to a dedicated outlet. Do not alter the cord or plug in any way. The entire length of the power supply cord must not, in any way, be compressed (bent or bunched together) nor may extension cords be used. This unit must be properly electrically grounded to avoid possible fatal electrical shock or serious injury to the operator. The power cord is provided with a three prong grounded plug. If a three-hole grounded electrical outlet is not available, use an approved method to ground the unit. Do not use extension cords with this unit. Do not “gang” together with other electrical devices on the same outlet.

How do I mix a drink?

Plug the drink mixer into a grounded outlet. Place the ingredients into the container supplied. The basic milkshake recipe is: 3 no. 24 scoops of ice cream, 4 ounces of very cold milk, and 1-1/2 ounces of syrup.

How do I operate the M1000 model?

Select the required speed using the 2-speed selector switch. Position the container in the container guide and move the container upwards to activate the mixer. Set the container down onto the upper level of the container rest. When the drink is completely mixed, lift the container up off the container rest and pull down from the container guide. The mixer will now turn off. The container can now be removed or left in the lower container guide position. Please note that the mixer will not operate without the container being in the upper position on the container rest.

How do I operate the M3000 model?

Select the desired speed using the 3-speed selector switch. Switch the toggle switch to the On position. Position the container in the container guide and move the container upwards to activate the mixer. Set the container down onto the upper part of the container rest. If the pulse operation is required, use the toggle switch to perform this function. When the drink is completely mixed, lift the container up off the container rest and pull down from the container guide. The unit will now turn off. The container can now be removed or left in the lower container guide position. Please note that the mixer will not operate without the container being in the upper position on the container rest.

How do I use the container rest to turn the unit off?

To turn the unit off, rest the container on the lower or standby container rest position.

How do I replace the agitator?

Unplug the mixer. If the shaft is to be removed, normally a quick turn counter clockwise will loosen the shaft. If not, remove the top cover and use a flat head screwdriver inserted into the top of the motor shaft to prevent the motor from turning. To remove the agitator, loosen the bolt by turning it counter clockwise with a 5/16” wrench. To install the new agitator, turn the bolt into the shaft and tighten. To prevent damage to the agitator, do not use pliers to grip the agitator blades while tightening or loosening. Inspect agitator(s) daily and replace every 90 days.

How do I remove and install the container guide pin and housing plug?

Unplug the drink mixer. Hold the container guide by the indents on each side and pull straight down. Press the retainer clip and slide the guide pin out of the guide. Reverse the above steps to reinstall, making note of the correct orientation.

How do I clean the mixer?

Place a drop of detergent and 1 cup of water into the container. Position the container into the container guide and mix on low speed for 5 seconds. Empty and refill with clean water and repeat for 5 seconds to rinse. Remove the container guide and wash with hot soapy water, then rinse. Clean the housing with a damp soapy cloth. Do not spray or submerge the mixer. Resulting water damage will not be covered under warranty.

How do I wall mount the mixer?

Remove m4x12 screws on the back of the machine. Separate main housing and base. Remove two black magnet covers. Fix the main housing on the wall by using the four screws and wall anchors supplied. Assemble two black magnet covers.