NUU MOBILE M2 (01) PDF MANUAL

NUU MOBILE M2 (01) PDF SUMMARY:

How do I set up my M2 phone?

Follow these step-by-step instructions to set up your M2. Power off the phone before inserting any cards!

---

What should I be careful of when handling SIM cards?

SIM cards are small enough to become a choking hazard, so please keep them away from children. SIM cards are also quite delicate. Please be careful when handling your card.

---

How do I remove the SIM tray?

Remove the SIM tray by inserting a pin eject key/paper clip in the small circular hole at the bottom of the tray. The tray will then eject from the phone.

---

What should I do after placing the SIMs and/or memory card in the tray?

After placing the SIMs and/or memory card in the tray, slide it back into its slot. It will snap and hold in place.

---

How do I charge the phone or transfer data?

Plug in the microUSB connector to charge the phone or transfer data.

---

How should I orient my SIM card on the tray?

Orient the SIM card to match the layout on the tray.

---

What type of SIM cards does SIM slot 1 and 2 support?

SIM 1 (Nano) supports 4G LTE connections and SIM 2 (Nano) supports 4G LTE connections.

---

What does the microSD card support?

The microSD card supports up to 64GB.

---

How do I obtain Warranty Service?

To obtain the Warranty Service, Customer must contact the authorized local distributor within the applicable warranty period to obtain warranty service authorization. Dated proof of original purchase from the authorized reseller will be required. NUU is not responsible for Customer’s products or parts received without a warranty service authorization. Products or parts shipped by Customer to local distributor must be sent prepaid and packaged appropriately for safe shipment, and it is recommended that they be insured or sent by a method that provides for tracking of the package.

---

When will NUU repair or replace the product without charge?

If you are experiencing any problems with the operation or function of your product, please make sure you have downloaded our full owner’s manual from our website for reference or contact the authorized local distributor. Should this fail to resolve the matter and service is still required by reason of any defect or malfunction during the warranty period, NUU will repair or, at its discretion, replace this product without charge. This decision is subject to verification of the defect or malfunction upon delivery of this product to a designated factory service center. The product must include proof of purchase, including date of purchase.

---

Under what conditions is NUU not liable under the warranty?

NUU shall not be liable under this warranty if its testing and examination disclose that the alleged defect or malfunction in the product does not exist or was caused by customer’s or any third person’s misuse, neglect, improper installation or testing, unauthorized attempts to open, repair, or modify the product, water damage, or any other cause beyond the range of the intended use, or by accident, fire, lightning, other hazards, or acts of God. This warranty does not cover physical damage to the surface of the product, including cracks or scratches on the outside casing. This warranty does not apply when the malfunction results from the use of this product in conjunction with accessories, other products, or ancillary or peripheral equipment and NUU determines that there is no fault with the product itself. This warranty does not apply to any malfunction or failure of the product or part due to any communication service customer may subscribe to or use with the product. Warranty is void if the warranty sticker is removed.

---

What are some of the FCC rules this device complies with?

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation.

---

What should I do if this equipment causes harmful interference to radio or television reception?

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

---

How do I comply with RF exposure requirements for body-worn operations?

To comply with RF exposure requirements, a minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

---

What are some of the Industry Canada license-exempt RSS standard(s) this device complies with?

Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

---

How do I comply with IC radiation exposure limits for an uncontrolled environment?

End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

---

What is the minimum separation distance required for body-worn operation to comply with RF exposure requirements?

A minimum separation distance of 10mm must be maintained between the user’s body and the handset, including the antenna.