NISSAN PATHFINDER 2024 (02) PDF Document

The cockpit of the NISSAN PATHFINDER 2024 includes the following components:

1. **Vehicle Information Display:** Shows important vehicle data and warnings.

2. **Low Tire Pressure Warning Light:** Illuminates when tire pressure is low.

3. **Headlight and Turn Signal Switch:** Controls exterior lights.

4. **Wiper and Washer Switch:** Controls front and rear wipers and washers.

5. **Vehicle Information Display / Audio Switches:** Controls for the display and audio system on the steering wheel.

6. **Cruise Control / Bluetooth® / Navigation / ProPILOT Assist Switches:** Steering wheel controls for various driving-assist and connectivity features.

7. **Instrument Brightness Control:** Adjusts the brightness of the instrument panel.

8. **Steering Assist Switch:** Activates or deactivates the Steering Assist feature (on models with ProPILOT Assist).

9. **Liftgate Switch:** Opens or closes the power liftgate.

10. **Head Up Display Switch:** Controls the Head Up Display (if equipped).

11. **Tilt / Telescopic Steering Column:** Lever to adjust the steering wheel position.

The instrument panel of the NISSAN PATHFINDER 2024 is equipped with the following features:

1. **Control Panel Display Screen:** The main screen for audio, navigation, and other vehicle settings.

2. **Audio System:** Controls for the radio and other media sources.

3. **Heater and Air Conditioner (automatic):** Controls for the climate system.

4. **Climate Control / Heated Seat Switches:** Dials and buttons to adjust temperature, fan speed, and activate heated seats (if equipped).

5. **Power Outlet:** A power source for electronic devices.

6. **USB Connection Port Interface:** Ports for connecting and charging devices, and for interfacing with the audio system.

7. **Hill Descent Control Switch:** Activates the Hill Descent Control system (if equipped).

8. **Hood Release:** Lever to open the vehicle’s hood.

To use the remote engine start feature on your NISSAN PATHFINDER 2024, the vehicle must be in Park (P) with the ignition off and all doors closed and locked. Follow these steps:

1. Press the lock button on the Intelligent Key.

2. Within 5 seconds, press and hold the engine start button for at least 2 seconds.

The engine will start, and the parking lights will turn on. The automatic climate control may also begin heating or cooling the vehicle. The engine will run for 20 minutes and then turn off. To start driving, depress the brake pedal and press the ignition switch inside the vehicle.

You can lock and unlock your NISSAN PATHFINDER 2024 using several methods with the Intelligent Key:

To lock the vehicle:

• Push any door handle lock sensor once.

• Press the lock button on the Intelligent Key.

To unlock the vehicle:

• Wrap your hand around a door handle to activate the capacitive unlock sensor. When using the driver’s door handle, only the driver’s door will unlock. You can then touch the lock sensor within 60 seconds to unlock all doors. When using the front passenger or rear door handles, all doors will unlock.

• Press the unlock button on the Intelligent Key to unlock the driver’s side door. Press it again to unlock all other doors.

To operate the power liftgate on your NISSAN PATHFINDER 2024:

To open the liftgate: Press and hold the HOLD button on the Intelligent Key for more than 1 second.

To close the liftgate: Press and hold the HOLD button on the Intelligent Key again for more than 1 second.

You can also open the liftgate by pushing the power liftgate switch on the instrument panel or by pushing the liftgate opener switch on the liftgate itself, provided the vehicle is unlocked or the Intelligent Key is nearby.

If the Intelligent Key battery is discharged, you can start the engine of your NISSAN PATHFINDER 2024 by following this procedure:

1. Push the park button to shift to the P (Park) position.

2. Firmly apply the foot brake.

3. Touch the ignition switch with the Intelligent Key. A chime will sound.

4. Within 10 seconds after the chime sounds, press the ignition switch while depressing the brake pedal, and the engine will start.

To adjust the front power seats (if so equipped) in your NISSAN PATHFINDER 2024, use the switches located on the side of the seat:

• **To slide the seat forward or backward:** Push the horizontal switch forward or backward.

• **To recline the seatback:** Push the vertical recline switch forward or backward.

• **Seat Lifter (driver’s seat):** Move the front part of the horizontal switch to adjust the angle of the seat cushion. Move the back part of the same switch to adjust the height of the seat.

• **Power Lumbar Support:** Move the round switch up or down to adjust the height of the lumbar support. Move it forward or rearward to increase or decrease the support.

To store a driving position in the Memory Seat system of your NISSAN PATHFINDER 2024, follow these steps:

1. Place the ignition in the ON or OFF position and confirm the vehicle is in Park (P).

2. Adjust the driver’s seat, steering column, and outside mirrors to your desired positions.

3. Push the SET switch.

4. Within 5 seconds, push the memory switch (1 or 2) for at least 1 second.

An indicator light will illuminate, and a beep will sound, confirming that the position is set.

2nd Row Seats:

• **To slide:** Pull the center of the bar under the seat up and hold it while you slide the seat to the desired position. Release the bar to lock it.

• **To recline:** Pull up on the recline lever on the side of the seat and lean back. Pull the lever up to bring the seatback forward.

• **To access the 3rd row:** Push the seat button on the side of the 2nd row seat. This will release the seatback and move the seat forward.

3rd Row Seats:

• **To fold flat:** First, pull the headrest straps to release the headrests. Then, pull the seat lever to release the rear seats, allowing the seatback to move forward and lay flat.

• **To return to upright position:** Pull the seat straps until the seats are locked back in place.

The Rear Door Alert in your NISSAN PATHFINDER 2024 is a system that reminds you to check the rear seat for objects or passengers. It activates if a rear door is opened and closed within 10 minutes of the vehicle being driven. When the system is active, a “Check Rear Seat for All Articles” warning will appear on the display, and the horn may sound.

To manage the alert:

• **To activate/deactivate:** Use the steering wheel buttons to navigate to “Settings” -> “Vehicle Settings” -> “Rear Door Alert”. You can choose from “OFF”, “Horn & Alert”, or “Alert Only”.

• **To dismiss a warning:** Use the scroll/OK button on the steering wheel to select “Dismiss Message”.

• **To temporarily disable:** Use the scroll/OK button to select “Disable Alert” for the current trip.

To start the engine:

1. Make sure the NISSAN Intelligent Key® is with you (e.g., in your pocket or purse).

2. Depress the brake pedal.

3. Press the ignition switch to start the engine.

To stop the engine:

1. Push the P (Park) button on the electronic shifter.

2. Apply the parking brake.

3. Push the ignition switch to turn the engine OFF.

To program the HomeLink® Universal Transceiver in your NISSAN PATHFINDER 2024 to operate a device like a garage door opener, follow these steps:

1. Place the ignition switch in the ON or ACC position (without starting the engine).

2. Press and release the HomeLink® button you wish to program. The indicator light will flash slowly.

3. Position your hand-held transmitter 1-3 inches away from the HomeLink® button.

4. While the HomeLink® indicator light is flashing, press and hold the button on your hand-held transmitter. Continue holding it until the HomeLink® indicator light changes.

5. To verify, press the programmed HomeLink® button. If the indicator light remains constant, programming is complete and your device should operate.

If the HomeLink® indicator light flashes rapidly, your device may have a rolling code. In this case, you need to press the “Learn” or “Set” button on your device’s motor unit (e.g., in the garage) and then, within 30 seconds, firmly press and hold the programmed HomeLink® button for 2 seconds and release it. Repeat this press-hold-release sequence up to three times to complete the programming.

The automatic climate control system in the NISSAN PATHFINDER 2024 can be operated as follows:

• **AUTO Mode:** Press the AUTO button. The system will automatically control fan speed, air flow distribution, and air intake to maintain the set temperature.

• **Temperature Control:** Turn the driver’s side or passenger’s side temperature control dial to adjust the temperature for each zone.

• **SYNC:** Press the SYNC button to synchronize the driver’s, front passenger’s, and rear temperature settings. Press it again to allow individual control.

• **ON/OFF:** Press the ON-OFF button to turn the system on or off.

• **Fan Speed:** Press the fan speed control buttons to manually increase or decrease fan speed.

• **Defrosting:** Press the front defroster button for the front and side windows, or the rear defroster button for the rear window and outside mirrors.

• **Air Recirculation:** Press the air recirculation button to recirculate interior air, which can help avoid outside odors and cool the interior more efficiently.

Headlight Control Switch:

• **Parking Lights:** Turn the switch to the first position.

• **Headlights:** Turn the switch to the second position.

• **AUTO:** Turn the switch to AUTO for the autolight system to automatically turn the headlights on or off based on ambient light.

• **High Beams:** With the low beams on, push the switch forward to activate the high beams. Pull it back to return to low beams. Pull and release the switch toward you to flash the high beams.

Wiper and Washer Switch (Windshield):

• **Intermittent (INT):** Push the lever down to the first position. Turn the knob to adjust the delay.

• **Low (LO):** Push the lever down to the second position for continuous low speed.

• **High (HI):** Push the lever down to the third position for continuous high speed.

• **Mist:** Push the lever up for a single sweep.

• **Washer:** Pull the lever toward you to spray washer fluid.

Rear Wiper and Washer:

• **Intermittent:** Turn the end of the switch to the first position.

• **Low:** Turn the end of the switch to the second position for continuous low speed.

• **Washer:** Push the lever forward to spray washer fluid on the rear window.

The Vehicle Information Display shows data such as vehicle settings, warnings, tire pressure, and trip computer information. To operate it, use the switches on the steering wheel:

• Use the left/right arrow buttons to enter and navigate through the main menu items.

• Use the scroll/OK button to move through items in a menu and to select or change an item.

• Press the back button to return to the previous menu.

To reset the trip computer: Navigate to the trip computer mode using the scroll/OK button. Press and hold the scroll/OK button for more than 1.5 seconds to reset values like average fuel consumption and journey time.

The Easy-Fill Tire Alert system on your NISSAN PATHFINDER 2024 provides visual and audible signals to help you inflate a tire to the recommended pressure. When a tire is low, a “Tire Pressure Low-Add Air” warning appears on the vehicle information display.

To use the system:

1. Push the P (Park) button and apply the parking brake.

2. Place the ignition switch in the ON position (do not start the engine).

3. Begin adding air to the under-inflated tire. The hazard warning lights will start flashing.

4. When the designated tire pressure is reached, the horn will beep once, and the hazard flashers will stop.

5. Repeat this procedure for any other under-inflated tires.

To stream audio from a compatible Bluetooth® device in your NISSAN PATHFINDER 2024, you first need to connect it as an audio device:

1. Press the SETTINGS button on the control panel and touch the “Connections” key on the display.

2. Touch the “Add New” key.

3. Press the gear icon on the screen to search for your device.

4. From your Bluetooth® device, select your vehicle to initiate the connection. Follow any on-screen prompts to complete pairing.

Once your device is connected:

• Press the AUDIO button on the control panel.

• Select the “Source” key.

• Select the “Bluetooth Audio” key to begin playback from your device.

For Apple CarPlay®:

Connect your compatible iPhone to the vehicle’s USB port or wirelessly via Bluetooth®. Follow the on-screen prompts to enable Apple CarPlay. The Apple CarPlay home screen will appear, allowing you to use compatible apps for calls, music, messages, and navigation through the vehicle’s display.

For Android Auto™:

Connect your compatible Android phone to the vehicle’s USB port. You may need to launch the app on your phone first. Follow the on-screen prompts to enable Android Auto. The Android Auto home screen will then appear on the vehicle display, giving you access to compatible apps.

For both systems, you can activate the respective voice assistant (Siri® for Apple, Google Assistant™ for Android) by pressing and holding the voice recognition button on the steering wheel.

Before shifting, ensure the engine is running and the brake is applied. The electronic shift lever returns to a home position after each selection; the selected gear is indicated on the lever and in the meter display.

• **To shift to R (Reverse):** Press the button on the side of the shift lever and slide the lever fully forward.

• **To shift to D (Drive):** Slide the lever fully rearward.

• **To shift to N (Neutral):** Slide the lever forward or rearward partially until you feel a slight increase in effort. Hold this position for 0.5 seconds.

• **To shift to P (Park):** Press the P (Park) button on top of the shift lever.

The vehicle will automatically shift to Park (P) if you turn off the ignition or unfasten your seatbelt and open the driver’s door while in R, N, or D.

The electronic parking brake is located on the center console.

• **To apply:** Pull the electronic parking brake switch up. The electronic parking brake indicator light will illuminate.

• **To release:** With the ignition switch in the ON position, depress the brake pedal and push the parking brake switch down. The indicator light will turn off.

ProPILOT Assist is a hands-on driver assistance system that combines Intelligent Cruise Control (ICC) and Steering Assist. It is intended for use on freeways/highways to help keep the vehicle centered in its lane and maintain a set distance from the vehicle ahead.

To activate ProPILOT Assist:

1. Push the ProPILOT Assist switch on the steering wheel. The system display will appear in the vehicle information display.

2. When you reach your desired speed, push the toggle switch down toward SET- to activate the system.

3. Push the distance switch to select your desired following distance from the vehicle ahead.

The driver must always be prepared to steer and brake the vehicle.

You can change the driving characteristics of your NISSAN PATHFINDER 2024 by turning the Drive Mode Selector dial on the center console. The selected mode will appear in the vehicle information display.

• **AUTO (4WD only):** Recommended for normal, everyday driving. This is the default mode.

• **SNOW:** Helps aid driving on slippery roads.

• **ECO:** Helps maximize fuel economy. Performance may be reduced.

• **MUD/RUT (4WD only):** Should be used in muddy areas.

• **SPORT:** Recommended for an enhanced performance feel. Fuel economy may be reduced.

• **SAND (4WD only):** Should be used in sandy areas.

• **TOW:** Should be used when towing a trailer.

The LDW and I-LI systems (if so equipped) are designed to help keep your NISSAN PATHFINDER 2024 in its traveling lane. They operate at speeds of approximately 37 mph (60 km/h) and above.

• **Lane Departure Warning (LDW):** If the vehicle approaches a lane marking, the system will vibrate the steering wheel and an indicator on the instrument panel will blink to alert you.

• **Intelligent Lane Intervention (I-LI):** This system can assist you in returning the vehicle to the center of the lane by applying individual brake pressure to the left or right wheels for a short period.

These systems can be turned on or off through the “Driver Assistance” menu in the vehicle information display.

The Head Up Display (HUD), if equipped, projects information such as vehicle speed, driving aids, and navigation onto the windshield in your line of sight.

• **To turn on/off:** Press the HUD switch on the lower instrument panel to the left of the steering wheel.

• **To adjust settings:**

1. Press the left/right arrow buttons on the steering wheel until you reach the “Settings” menu in the vehicle information display.

2. Use the scroll/OK dial to select “Head-Up Display”.

3. From this menu, you can adjust features such as Brightness, Rotation, Height, and what Content is displayed.