NENO COMO (01) PDF MANUAL

When using the NENO COMO cot, please adhere to the following precautions:

1. To avoid injury, make sure children are at a safe distance when folding and unfolding the product.

2. Keep the power supply out of the reach of children.

3. Do not use the product if any component is damaged or missing.

4. Do not use accessories or spare parts other than those supplied.

5. Do not store the device near water or a heat source. Be aware of the risks of smoking and using open flames near the cot.

6. Do not use the product if the child’s weight exceeds 9kg (cot, freestanding and cradle function) and 15kg (playpen function) or from the time the child can sit up, kneel down or pull themselves up unaided.

7. Do not lift the product if a child is inside.

8. Never use this product on elevated surfaces such as a table.

9. The product should only be used on flat, dry surfaces.

10. Do not use a power supply other than the one supplied with the product to power the product.

11. Always check all fixings before use and ensure that the components are correctly fitted and aligned.

12. Check regularly the condition of seams, material joints, structures, and screws. If wear is detected, discontinue use immediately.

13. Always remember to use a security system (securing straps, locks).

14. Children should not play without adult supervision near the cot.

15. The cot must be locked in a fixed position when the child is left unattended.

16. When transforming the function of the cot, the child must not be inside.

To prevent the risk of suffocation with the NENO COMO, please follow these guidelines:

• Placing additional objects in the product (such as pillows, duvets, and extra filling) can cause suffocation.

• Use ONLY the mattress supplied by the manufacturer.

• Do not use more than one mattress.

• Do not place the product near another product (containing cords, cables, etc.) due to the risk of suffocation.

• Remove all packaging immediately after opening and keep it out of the reach of children.

To prevent serious injury from entrapment with the NENO COMO:

• The cot must be properly secured to the adult bed using the attachment straps.

• Always read and follow the assembly instructions for each product function (cot, free-standing cot, cradle, playpen).

• Always use ALL the required parts for each function (cot, free-standing cot, cradle, playpen).

To mitigate the risk of collapse or falls with the NENO COMO:

• To prevent falls, stop using the product when the infant starts to sit, kneel, or pull himself up.

• Periodically check the product for loose, damaged, or missing parts. DO NOT use if any part is loose or missing or if there are any signs of damage. DO NOT substitute parts.

• DO NOT place any cord, belt, or similar object inside or near this product that could wrap around a child’s neck.

• In freestanding cot mode, make sure the side panel is raised and locked.

• Never leave an infant with the side panel down, unless the cot is attached to the adult bed using the attachment straps.

• Always remember to lock the cradle function when the product is not being used as a cradle. The cradle function must be used under adult supervision.

The NENO COMO kit includes the following items:

1. Cot:

– Vertical supports x2 (1x main element containing the motor and touch panel + 1x support element)

– Legs x2 + locking castors x4

– Front rim

– Rear rim

– Plate

– Fabric

– Bottom bracket

– Lower rim x2

2. Mattress with cover

3. Mosquito net

4. Fixing straps x2

5. Power supply with cable

6. Remote

7. Operating instructions

To assemble the NENO COMO, follow these steps. Note: This product must be assembled by an adult.

1. Insert two castors into each of the legs. Then, mount the legs to the vertical supports using two screws for each side.

2. Mount the bottom bracket to connect the two vertical supports, using one screw on each side.

3. If you plan to use the product as a co-sleeper, place the shorter part of the securing straps over the plastic element on both sides. Mount the two lower rims (the thinner ones) by inserting them into the plastic elements on the vertical supports. Ensure you hear a “click” to confirm they are correctly mounted. Then, place the plate onto the mounted lower rims.

4. Insert the front and rear upper rims into the fabric, ensuring the front rim is on the side with the lower opening for the playpen function. Pass the fabric under the lower rims and plate assembly. Next, mount the rear upper rim to the plastic elements at the top of the vertical supports, listening for a “click”. Slide the front upper rim up from the bottom into the plastic guide rail; a lock at the bottom of the rail will click into place. Finally, zip up the fabric on both sides.

5. Place the mattress with its cover on the plate inside the cot.

The NENO COMO features several locks for safety and functionality:

1. Wheel Lock: Press the lock on each wheel down to block movement. Lift the lock up to unblock.

2. Height Adjustment Lock: To adjust the height (7 levels), press the buttons on both vertical supports simultaneously while gently lifting the cot bassinet.

3. Rocking/Bouncing Lock: Press the lock located on the inner side of both vertical supports. An element will extend to fit into a designated slot on the bottom support, locking the rocking function. To unlock, push the element up while holding it from both sides.

4. Side Panel Lock: To lower the side panel, slide the locks on both sides of the panel outwards simultaneously.

To use the NENO COMO as a co-sleeper, ensure the child is not inside the cot during conversion, and follow these steps:

1. Convert from playpen to cot mode by zipping up the zippers located in the middle and bottom of the fabric on both sides.

2. Lower the side panel by sliding the side panel locks outwards and unzipping the side zippers.

3. Adjust the cot’s height so that the mattress of the parents’ bed is at the same level as, or slightly above, the lowered side panel of the cot.

4. Use the securing straps to attach the NENO COMO to the parents’ bed. The shorter part of the straps should have been placed on the plastic element during assembly. Wrap the longer part of the straps around the parents’ mattress or bed frame and fasten the buckle. Adjust the length so the cot is held firmly against the parents’ bed with no gap. Tuck any excess strap under the parents’ mattress.

5. Ensure there is no gap between the cot and the parents’ bed.

6. Lock the wheels and the rocking function.

NOTE: Do not place the child in the cot with the side panel down unless it is securely attached to the parents’ bed. This function cannot be used with waterbeds or round-shaped beds.

To use the NENO COMO as a free-standing cot, ensure the child is not inside during conversion:

1. Convert from playpen to cot mode by zipping the zippers in the middle and bottom of the fabric on both sides.

2. Make sure the side panel is raised and the side zippers are fully zipped up.

3. Adjust the height as needed. In this mode, you can also adjust the angle of inclination, ensuring the child’s head is higher than the rest of the body. The maximum inclination is a difference of two height levels.

4. Lock the wheels and the rocking function.

NOTE: The angle adjustment function is ONLY available in the free-standing cot mode.

To use the NENO COMO as a cradle, ensure the child is not inside during conversion:

1. Convert from playpen to cot mode by zipping up the middle and bottom zippers on both sides of the fabric.

2. Ensure the side panel is raised and the side zippers are zipped up.

3. Adjust the height to your needs. It is suggested to use the lowest height levels for the cradle function.

4. Lock the wheels.

5. Unlock the rocking function by sliding the locking element up on both vertical supports.

6. The cradle function can be controlled from the display panel or the remote control. Adjust the rocking level to the child’s needs and ensure the child is lying in the central part of the cot.

WARNING: The cradle function must be used ONLY under adult supervision. Before starting the rocking function, ensure the rocking lock is disengaged and there are no obstructions nearby that could collide with the product.

To convert the NENO COMO into a playpen, ensure the child is not inside during conversion:

1. Unzip the middle zippers on both sides of the fabric. This lowers the mattress to the playpen position.

2. Ensure the side panel is raised and the side zippers are zipped up.

3. The cot should be set at the highest height level.

4. Lock the wheels and the rocking function.

WARNING: Ensure there are no dangerous items inside the playpen. Do not leave the child unattended if the playpen entrance opening is unzipped.

The display panel of the NENO COMO has the following indicators and controls:

1. Rocking level indicator: Shows the current rocking speed.

2. Set time indicator: Shows the time set for the timer function.

3. Cradle function button: Activates the rocking motion.

4. Timer button: Sets the duration for the rocking function.

5. Intelligent sleep mode button: Activates the motion-sensing sleep mode.

6. Music button: Controls music playback.

7. Power on/off button: Turns the device on or off.

The intelligent sleep mode should only be used when the NENO COMO is in the free-standing cot mode. To operate it:

1. Turn on the device using the power button (B7). Then, press the intelligent sleep mode button (B5) on the display.

2. A flashing ‘3’ will appear on the rocking level indicator. The mode is now active and in standby.

3. When the device detects the child’s movement, it will automatically start rocking at level 3 for 3 minutes. The set time indicator will count down the 3 minutes.

4. After the 3-minute cycle, the mode will return to standby, waiting to detect the next movement.

5. To turn off the intelligent sleep mode, press the button (B5) again.

You can play music on the NENO COMO using the built-in melodies or via Bluetooth:

Built-in Melodies:

• To play the built-in melodies, press the music button (B6) on the display. Press it again to switch to the next track.

• To adjust the volume, press and hold the music button (B6) for 2-8 seconds.

• To turn the music off, press and hold the music button (B6) for more than 8 seconds.

Bluetooth Connection:

• Connect to the device via Bluetooth on your smartphone. The device name is “PT-BABY”. The unit will make a sound to confirm a successful connection.

NOTE: Before playing music, ensure the volume level is not too high for the child.

The remote control for the NENO COMO has the following functions:

1. Power on/off: Turns the device on or off.

2. Decrease rocking level: Reduces the rocking speed.

3. Start/Increase rocking level: Starts the rocking function or increases its speed.

4. Increase volume: Turns the music volume up.

5. Decrease volume: Turns the music volume down.

6. Previous song: Skips to the previous music track.

7. Next song: Skips to the next music track.

8. Music on/off: Plays or stops the music.

9. Play/Pause: Pauses or resumes the music or rocking function.

10. Timer: Sets the rocking duration to 8, 15, or 30 minutes.

11. Intelligent sleep mode: Activates or deactivates the intelligent sleep mode.

NOTE: The remote is powered by one CR2025 battery, which is included. Remove the protective film before first use.

The electronic functions of the NENO COMO, including the cradle, timer, intelligent sleep mode, and music, will operate when the unit is connected to a power source using the charger and cable supplied with the set.

To attach the mosquito net to the NENO COMO, place the net over the cot and fasten the clips located on both sides of the upper part of the mesh.

To clean and maintain your NENO COMO:

1. Clean the steel and plastic parts of the device with a damp cloth. Do not use detergents. Then, wipe it dry to ensure no water marks are visible.

2. To wash the fabric, unzip the zipper and remove it from the metal frame of the cot. The fabric should be machine washed in warm water on a delicate cycle. Do not use bleach. Do not tumble dry. Do not iron.

3. The mattress cover can also be removed and washed in warm water with a mild detergent, without bleach.

4. Failure to follow these recommendations may result in discoloration, distortion, or damage to the components.

5. When the product is not in use, it should be stored in a dry place.

Input: 6V 1A

Material: Steel, PP, ABS, polyester linen

Dimensions: 92x55x112cm

Mattress dimensions: 89x50cm

Height from floor to top edge of mattress: 27-51cm

Length of securing straps: 5m

Cable length: 1.8m

Weight: 12.5kg

Maximum radio frequency power emitted in the frequency range: -3.03 dBm

Frequency range: 2.402-2.480 GHz

The crossed-out trash can symbol on the NENO COMO indicates that unusable electrical or electronic devices, its accessories (such as power supplies, cords), or components (for example batteries, if included) cannot be disposed of alongside household waste. To dispose of the device or its components, deliver the device to the designated collection point, where it will be accepted free of charge. Proper disposal of the device prevents degradation of the natural environment. Incorrect disposal of waste is subject to penalties provided for by the law in force in the given area.