MPM MBL-37 (01) PDF Document

Before using your MPM MBL-37, please adhere to the following safety guidelines:

– Read the operating instructions carefully before use.

– Do not hold the device with wet hands.

– Be especially careful when there are children near the appliance.

– Do not use the appliance for any purpose other than its intended purpose.

– Do not immerse the appliance, cord and plug in water or other liquids.

– Do not allow the power cord to dangle from the edge of the table/countertop.

– Do not leave the device unattended during operation.

– Do not use a damaged device, even if the mains cord or plug is damaged; return it to an authorized service center for repair.

– Do not use the appliance in the open air.

– Do not hang the power cord on sharp edges or allow it to contact hot surfaces.

– Do not place the device on or near other electrical appliances, burners, stoves, or ovens.

– The device must be placed on a dry, flat and stable surface.

– The device is intended for home use only.

– Always ensure all components are installed correctly before starting.

– The use of accessories not recommended by the manufacturer may cause damage, fire, or personal injury.

– The device may be used by persons with reduced physical, sensory or mental capabilities, provided they are supervised or instructed on safe use and understand the risks involved.

– The device cannot be used by children. Keep the appliance and cord out of the reach of children.

– Children are not allowed to carry out cleaning and maintenance activities.

– Pay attention to children so that they do not play with the device.

– Do not pull the plug from the mains socket by pulling the cord.

– The equipment is not intended to operate with external timers or a separate remote control system.

– For the safety of children, do not leave parts of the packaging (plastic bags, cartons, styrofoam, etc.) freely accessible.

– Check that the power parameters on the rating plate of the device correspond to those of your power supply network.

– Keep your hands away from moving parts while the appliance is operating.

– Do not remove the jug of the blender during operation.

– When mixing, do not put any objects in the jug, e.g., spoons, spatulas, etc.

Please take note of the following critical warnings when using your MPM MBL-37:

WARNING! Do not allow children to play with foil. Danger of suffocation!

ATTENTION! Before starting cleaning and maintenance, disconnect the appliance from the mains and wait for it to cool completely after operation. Do not immerse the device in water!

ATTENTION! Do not use sharp objects, abrasive pastes, solvents and other strong chemicals for cleaning – their use may damage the device.

ATTENTION! The cutting blades are very sharp, avoid physical contact when emptying and cleaning the unit – you can seriously injure yourself.

ATTENTION! Do not use the blender without the jug lid installed correctly!

ATTENTION! Before pouring the contents from the jug, wait until the knife stops!

ATTENTION! Do not exceed the permissible operating time indicated on the nameplate. Wait for the device to cool down before starting the next time.

ATTENTION! Do not fill the jug of the blender with boiling liquids.

ATTENTION! Do not start the blender with an empty jug.

ATTENTION! If the motor stops, immediately switch off the blender, remove the jug from the main unit and remove excess ingredients from the jug.

The MPM MBL-37 consists of the following components:

1. Blender housing

2. ON/OFF knob – two-speed operation and PULSE function

3. Jug mounting socket

4. Rubber seal

5. Pitcher base ring with stainless steel knife

6. 1500 ml glass blender jug

7. Jug handle

8. Jug cover

9. Jug cover cap

10. Non-slip feet

Follow these steps to assemble the blender jug:

1. Make sure that a rubber seal is properly installed inside the jug base ring (5).

CAUTION! The blades are sharp. Handle with care. Handle the knife only by its plastic base.

2. Turn the blender jug (6) so that the opening for screwing the base on is pointed upwards.

3. Place the jug base ring (5) over the hole with the knife facing the inside of the jug and screw it in clockwise, taking care to fit the threads correctly.

In case of deinstallation of the jug base ring (5), act in a reverse order.

Note: The appliance is equipped with a safety system to prevent accidental start-up. If the jug is incorrectly fitted, the blender will not start.

NOTE: The appliance is designed for blending food at a temperature of no more than 50 °C.

1. Place the blender housing (1) on a dry, hard and even surface.

2. After making sure that all blender jug parts are assembled correctly, put the blender jug (6) on the blender enclosure (1) and gently turn it clockwise. Ensure that the latches fit correctly.

3. Cut the products into smaller parts to make mixing easier. Put ingredients into the jug only when the motor is stopped.

NOTE! Do not fill the jug above the mark of 1500ml (6).

4. Place the lid with the hole plug.

5. Plug the appliance into the power supply socket.

6. Turn it on with the knob (2), choosing one of two operating modes.

7. During mixing always hold the lid. If you need to add ingredients when the cup blender is running, remove the hole plug from the lid (9) and feed the ingredients through the hole, and then replace the plug (9).

8. When mixing is complete stop the appliance by turning the knob (2) to the “<>” position and unplug the power supply plug from the socket.

9. Certain products, e.g. ice cubes, should be crushed by repeatedly using the PULSE function. The PULSE function works by turning and holding the switch knob to the left as far as it will go. To improve crushing of the ice cubes, pour a small amount of water.

ATTENTION! Before pouring out the content of the jug wait until the knife stops rotating!

NOTE! Do not start the motor for more than 1 minute, because it may become overheated. After this 1 minute stop the appliance and wait until it cools down but not less than 3 minutes.

The MPM MBL-37 is not designed for the following tasks:

• grating potatoes

• whipping eggs or dairy products substitutes

• mincing raw meat

• whipping or kneading dough (danger of forming a ball of dough which may damage the appliance)

• juicing vegetables and fruit

Additionally, boiled vegetables and fruit should cool down before being put into the blender jug.

CAUTION! Before cleaning, always unplug the appliance from the mains outlet and wait until it has completely cooled down.

CAUTION! Do not immerse the blender housing in water or other liquids.

CAUTION! The blades are very sharp. Handle with care to avoid injury.

1. Blender components are corrosion-proof and easy to clean.

2. Each time before and after using, disassemble the appliance and wash its parts in warm water with detergent, rinse and dry them thoroughly.

3. They should not be used in washing machines.

4. Periodically check all operating components of the appliance before using them. Do not use the blender if the blades got stuck or rotate with difficulty. Turn them clockwise to check if they operate properly. Be careful not to get injured. The blades should rotate easily.

5. Do not use the appliance if the jug gets damaged, leaks or has fractures of cracks. Otherwise it may crack while in use.

6. To clean the blender housing, unplug the appliance and then wipe it with a damp cloth. If water gets to the top of the appliance, it will go down and through the drain hole under the housing.

7. The motor does not require any additional maintenance. Do not clean the appliance using harsh or abrasive cleaning agents, materials or steel wool, which may cause damage.

The marking on the product indicates that after its service-life expires, it should not be disposed of with other types of municipal waste. Used equipment may have a negative impact on the environment and health due to potentially containing hazardous substances. Mixing electric waste with other types of waste or disassembling it in an unprofessional manner may release hazardous substances. Used equipment should be handed over to a designated collection point for electric waste. For detailed information, contact your municipal point of electric waste collection or a used equipment processing department.