Free English MOTOROLA NURSERY PIP15 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MOTOROLA NURSERY PIP15 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How long should I charge the MOTOROLA NURSERY PIP15 before initial use?
You must charge both the parent unit and the baby units for 16 hours before initial use. When charging the batteries for the first time, charge for at least 16 hours continuously. After charging for the first time, subsequent charging time is about 8 to 10 hours a day.
How do I install batteries into the MOTOROLA NURSERY PIP15 baby unit?
Warning: Use only the approved rechargeable Ni-MH battery cells (2 x AAA Ni-MH rechargeable batteries) supplied with your unit.
1. Lift up the battery cover to remove it from the baby unit.
2. Insert the rechargeable Ni-MH battery cells supplied. Note the ’+’ and ’-’ markings beside the battery compartment and insert in the correct direction.
3. Place the battery cover back into place.
4. To install batteries into another baby unit, repeat the above steps.
How do I connect and charge the MOTOROLA NURSERY PIP15 baby unit?
1. Plug the supplied USB type-C cable into the USB-C power socket.
2. Plug the USB-C power socket cable into the power jack on the side of the unit and plug the other end into the wall socket.
3. Switch on the AC power (if your AC power outlet has a switch). The battery charging LED indicator will light up in red and turn dim when the batteries are fully charged.
4. To connect another baby unit, repeat the above steps.
How do I install batteries into the MOTOROLA NURSERY PIP15 parent unit?
Warning: Use only the approved rechargeable Ni-MH battery cells (2 x AAA Ni-MH rechargeable batteries) supplied with your unit.
1. Lift up the battery cover to remove it from the parent unit.
2. Insert the rechargeable Ni-MH battery cells supplied. Note the ’+’ and ’-’ markings inside the battery compartment and insert in the correct direction.
3. Place the battery cover back into place.
How do I connect and charge the MOTOROLA NURSERY PIP15 parent unit?
1. Plug the supplied USB type-C cable into the USB-C power socket.
2. Plug the USB-C power socket cable into the power jack on the side of the parent unit and plug the other end into the wall socket.
3. Switch on the AC power (if your AC power outlet has a switch). When the parent unit is fully charged, the battery icon will appear steadily on the screen display.
Where should I place the MOTOROLA NURSERY PIP15 baby unit?
Determine a location for the baby unit that will allow you to hear your baby in his/her cot. Place the baby unit on a flat surface, such as a dresser, bureau, or shelf. Do not place the unit in the bathroom or other humid areas.
WARNING: Strangulation Hazard. Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 1 metre / 3 feet away). NEVER place the baby unit or cords within the cot.
How do I avoid audio feedback or noise interference on the MOTOROLA NURSERY PIP15?
Make sure there is a minimum distance of 2 meters (6 feet) between the parent and baby units to avoid audio feedback. If there is noise interference, move the baby and parent units further apart.
Additionally, make sure the parent and baby units are not placed near other electrical equipment. Move the parent and baby units 2 meters (6 feet) away from other electrical equipment.
How do I turn the MOTOROLA NURSERY PIP15 baby unit on and off?
To turn on: Press and hold the power button on the baby unit. The power LED indicator lights up in red first and becomes green.
To turn off: Press and hold the power button on the baby unit again. The power LED indicator will turn off.
How do I turn the MOTOROLA NURSERY PIP15 parent unit on and off?
To turn on: Press and hold the power button on the parent unit. The power / linking LED indicator lights up in green.
To turn off: Press and hold the power button on the parent unit again. You will hear a beep sound, and the power / linking LED indicator will turn off.
How do I use the listening and cycling modes on the MOTOROLA NURSERY PIP15?
In standby mode, press the OK button continuously to select to listen to an individual baby unit or all baby units.
When a baby unit is selected, the screen will display a bordered box around the chosen baby unit, and you will be able to listen to that unit.
When two or more baby units are connected, you can select to listen to all baby units (screen displays a bordered box around all baby units).
Alternatively, you can select to cycle through all connected units. The listened baby unit is surrounded by a bordered box, with each segment lasting 15 seconds.
How do I adjust the speaker volume on the MOTOROLA NURSERY PIP15 parent unit?
Press the Up or Down arrow buttons to increase or decrease the volume. It has 5 volume levels and mute.
How do I mute the speaker on the MOTOROLA NURSERY PIP15 parent unit?
Press continuously or press and hold the Down arrow/Mute button to mute the speaker of the parent unit. When it is muted, the mute icon will be displayed.
How do I use the Talk Back feature on the MOTOROLA NURSERY PIP15?
Press the microphone button continuously on the parent unit to select an individual baby unit or all baby units. The screen will display the microphone icon with the baby unit number(s) selected.
Press and hold the microphone button, and speak to your baby/babies through the microphone of the parent unit. Release the button when you finish speaking.
In standby mode, press and hold the microphone button to speak directly to all babies.
How do I name the baby units on the MOTOROLA NURSERY PIP15?
1. Press MENU then scroll left/right to select NAME, then press OK.
2. Scroll up/down to select a baby unit, then press OK.
3. Scroll left or right to select a character on the screen, then press OK to confirm. The character will be added.
4. To remove a character, scroll left or right to select X and press OK.
5. Repeat the same process until you finish editing. The maximum number of characters is limited to 5.
6. Scroll left or right to select the checkmark symbol to save the name.
How do I register or pair a baby unit to the MOTOROLA NURSERY PIP15?
1. Make sure the baby unit is switched off.
2. Press and hold the power button on the baby unit until you hear a beep tone and the LED on the baby unit flashes. The baby unit enters pairing mode.
3. On the parent unit, press MENU then scroll left/right to REGISTER.
4. Press OK then scroll up/down to PAIR.
5. Press OK to confirm. When pairing is successful, SUCCEED will appear on the screen and you will hear a beep tone.
How do I deregister or unpair a baby unit on the MOTOROLA NURSERY PIP15?
1. On the parent unit, press MENU then scroll left/right to REGISTER.
2. Press OK then scroll up/down to UNPAIR.
3. Press OK then scroll up/down to select a baby unit.
4. Press OK to confirm. When unpairing is successful, SUCCEED will appear on the screen and you will hear a beep tone.
How do I reset the MOTOROLA NURSERY PIP15 baby monitor?
1. Press MENU then scroll left/right to RESET.
2. Press OK two times to confirm.
How do I set the temperature format and alerts on the MOTOROLA NURSERY PIP15?
To set the temperature format (C/F):
1. Press MENU then scroll left/right to TEMPERATURE.
2. Press OK then scroll up/down to °C/°F.
3. Press OK then scroll up/down to select a desired option. Press OK to confirm.
To set the temperature alert:
1. Press MENU then scroll left/right to TEMPERATURE.
2. Press OK then scroll up/down to TEMP ALERT.
3. Press OK then scroll up/down to select HIGH TEMP/LOW TEMP.
4. Press OK then press up/down to adjust the temperature. Press OK to confirm.
Note: You can only set the lowest and highest temperature for all baby units but not to an individual unit. The temperature range is limited to 14°C/57°F and 39°C/102°F.
How do I operate the night light on the MOTOROLA NURSERY PIP15?
From the Baby Unit:
Single press the Power/Night light button to toggle the brightness of the night light from off, low, medium, and high.
From the Parent Unit:
1. Press MENU then scroll left/right to NIGHT LIGHT.
2. Press OK then scroll up/down to select a baby unit.
3. Press OK and scroll up/down to choose among OFF / LOW / MEDIUM or HIGH. Press OK to confirm.
How do I play lullabies on the MOTOROLA NURSERY PIP15?
1. Make sure the baby unit(s) are switched on.
2. On the parent unit, press MENU then scroll left/right to LULLABY.
3. Press OK then scroll up/down to select a baby unit, press OK two times to confirm.
To stop lullabies: Repeat steps 2 and 3.
To select a lullaby: Repeat step 2. Select a baby unit, press OK then scroll up/down to CHOOSE. Press OK and scroll up/down to the desired option (5 lullabies or PLAY ALL). Press OK to confirm.
To adjust play time: Repeat step 2. Select a baby unit, press OK and scroll up/down to TIMER. Press OK and scroll up/down to the desired TIMER (5MIN / 10MIN / 15MIN or CONSTANT). Press OK to confirm.
How do I adjust the VOX (Voice Activated Alert) level on the MOTOROLA NURSERY PIP15?
1. Press MENU then scroll left/right to VOX.
2. Press OK then scroll up/down to select LEVEL.
3. Press OK then scroll up/down to select a baby unit.
4. Press OK and scroll up/down to choose among 4 levels or OFF. Press OK to confirm.
About Levels:
OFF: All sounds will be detected and heard from the parent unit.
LEVEL 1: Lowest sensitivity. Only loud crying or screeching sounds will be heard.
LEVEL 4: High sensitivity. Louder baby sounds will be detected.
Why does the power/linking LED indicator on the MOTOROLA NURSERY PIP15 parent unit flash?
The parent unit and the baby unit may be out of range with each other. Reduce the distance between the units. Make sure the distance between the parent unit and baby unit is less than 450 meters (1500 feet).
Alternatively, the baby unit may be powered off. Press and hold the power button on the baby unit to power it on.
Why can’t I hear sound or the baby cry from the MOTOROLA NURSERY PIP15 parent unit?
The volume level in the parent unit may be set too low. Increase the volume level of the parent unit.
The parent unit and the baby unit may be out of range with each other. Make sure the distance between the parent unit and baby unit is less than 450 meters (1500 feet).
Why does the MOTOROLA NURSERY PIP15 produce a high-pitched noise?
The parent unit and the baby unit are too close with each other. Move the baby and parent units further apart.
Alternatively, the speaker volume of the parent unit may be set too high. Decrease the volume of the parent unit.
How should I clean the MOTOROLA NURSERY PIP15?
Clean your audio baby monitor with a slightly damp cloth or with an anti-static cloth. Never use cleaning agents or abrasive solvents.
Do not clean any part of the audio baby monitor with thinners or other solvents and chemicals, as this may cause permanent damage to the product.
What is the battery performance of the MOTOROLA NURSERY PIP15?
For the parent unit:
12 hours for a single baby unit
9 hours for two baby units
6.7 hours for three baby units
5.5 hours for four baby units
For the baby unit:
14 hours when both night light and lullaby are OFF
11.5 hours when the lullaby is ON
10 hours when the night light is ON
9 hours when both night light and lullaby are ON
CLICK HERE TO DOWNLOAD MOTOROLA NURSERY PIP15 (01) PDF DOCUMENT