MOBVOI HOME WALKING TREADMILL FIT TM09 (01) PDF MANUAL

Place the treadmill in a well-ventilated, dry indoor area away from moisture and foreign objects.

Wear appropriate sportswear and sports shoes; perform stretches before exercise. Do not exercise barefoot.

Ensure the power plug is securely grounded and uses a dedicated circuit.

Keep children away from the equipment.

Avoid prolonged operation under overload conditions.

Perform regular maintenance.

Reduce indoor dust and maintain appropriate humidity to prevent electrostatic interference.

Turn off the power after use.

Maintain indoor air circulation during use.

If you feel discomfort or abnormal conditions, stop immediately and consult a medical professional.

Store silicone oil away from children after use.

Ensure a safety area of 39.37*78.74 inches (1000*2000mm) behind the treadmill.

Avoid placing the treadmill on a carpet or uneven floors.

Check if clothing is properly fastened or zipped up before use.

Avoid wearing items that may get caught by the treadmill.

Keep the power cord away from heat sources.

Prevent children from approaching the treadmill.

Do not use the treadmill outdoors.

Disconnect the power before moving the treadmill.

Do not open the upper cover and rear seats without professional supervision.

Only one person should exercise on the treadmill at a time.

If you feel dizziness, chest pain, nausea, or shortness of breath, stop immediately and consult a medical professional.

Individuals undergoing medical treatment or those with specific conditions should consult a professional doctor before use. This includes, but is not limited to:

Patients with lower back pain, leg/neck/arm injuries, disc herniation, spinal slippage, cervical protrusion.

Patients with osteoarthritis, rheumatism, or painful rheumatism.

Individuals with osteoporosis.

Individuals with circulatory system diseases (heart disease, vascular disease, high blood pressure).

Individuals with respiratory organ disorders.

Individuals using artificial pacemakers or implanted medical electronic devices.

Individuals with malignant tumors.

Individuals with thrombosis, severe blood circulation disorders, acute venous inflammation.

Individuals with peripheral circulation disorders (e.g., diabetes).

Individuals with skin wounds.

Individuals with fever (38°C or above).

Individuals with abnormal or bent backs.

Pregnant or potentially pregnant women, or women in menstruation.

Individuals feeling physically abnormal and needing rest.

Individuals with obvious poor physical condition.

Individuals using the equipment for rehabilitation.

Individuals who feel any abnormality in their body not listed above.

Do not use if the housing is cracked, broken, or detached, or if welded parts are detached.

Do not jump on or off the treadmill during exercise.

Do not use or store outdoors, in the bathroom, or in damp/wet places.

Do not place in direct sunlight or near high-temperature sources (fireplace, heating devices).

Do not use if the power cord/plug is damaged or the socket is loose.

Do not damage, bend, twist, place heavy objects on, or pinch the power cord.

Do not allow two or more people to use it simultaneously.

Do not allow individuals who cannot express consciousness or operate independently to use it.

Absolutely do not disassemble, repair, or replace components yourself.

Do not allow the main body or controls to contact water or conductive liquids.

People who do not exercise regularly should not engage in strenuous exercise suddenly.

Do not use after drinking water, when fatigued, during early exercise stages, or when the body is abnormal.

Do not use during drinking, eating, or other activities.

Do not use when feeling sluggish after drinking.

Do not use with hard objects in pockets.

Do not allow needles, garbage, or water to attach to the power plug.

Do not pull out the power plug or switch the power to “off” during use.

Do not pull out or insert the power plug with wet hands.

When the equipment is not in use.

When performing maintenance.

If the equipment cannot start or abnormalities occur (stop use immediately and contact professional repair).

During a power outage.

When pulling out the plug, grip the plug itself, not the wire portion.

This product requires grounding to reduce the risk of electric shock if it malfunctions.

It is equipped with a grounding wire and plug.

The plug must be inserted into a properly installed and grounded socket compliant with local regulations.

Improper connection of the grounding conductor can result in electric shock. Consult a professional electrician if unsure about grounding.

Do not modify the plug if it doesn’t fit the socket; have a professional electrician install an appropriate socket.

Ensure the product is connected to a socket matching its plug shape.

This product cannot be plugged into an adapter.

Working Voltage	AC 110V 60Hz
Maximum Load	220lbs
Product Size	43.5″x18.11″x4.25″
Running Area	15″x35.4″
Maximum Power	1.65hp
Displayed Speed	1.0-4.0mph
Control Method	Remote Control

Foot pad*4

5# Hex Wrench*1

Methyl Silicone Oil*1

Remote Control*1

Instruction Manual*1

1. Take the main unit out of the packaging and place it flat on the floor.

2. Tighten the foot pads clockwise into the screw holes to secure them.

3. Ensure all foot pads at the bottom are flush with the ground after installation.

4. Plug in the power plug and turn on the power switch on the front of the treadmill. It will enter standby mode.

Warm-up: Perform a 5-10 minute warm-up before each session.

Breathing: Breathe regularly and coordinate with movements. Stop if breathing becomes too rapid.

Frequency: Allow a 48-hour rest period for the same muscle group; don’t train it on consecutive days.

Training Load: Determine load based on personal fitness and follow progressive overload. Initial muscle soreness is normal.

Relaxation: Perform a 5-minute cool-down after each session, including stretching.

Diet and Hydration: Exercise at least one hour after a meal. Avoid eating immediately after exercise. Drink water sparingly during exercise.

Perform these 5 times, holding each for 10-15 seconds, repeating 3 times for each leg/stretch where applicable, both before and after walking.

1. Forward Stretch: Knees slightly bent, lean forward slowly, relax back/shoulders. Try to touch toes. Hold, relax, repeat.

2. Achilles Tendon Stretch: Sit on a mat, one leg straight. Bring other leg inward against the straight leg’s inner side. Try to touch toes of the straight leg. Hold, relax, repeat for each leg.

3. Calf and Heel Tendon Stretch: Stand facing a wall, hands against it. One foot back, keep back leg straight, heel on the ground. Lean towards the wall. Hold, relax, repeat for each leg.

4. Quadriceps Stretch: Hold wall/table for balance. Extend right hand back, grab right ankle, slowly pull towards buttocks. Feel front thigh tension. Hold, relax, repeat for each leg.

5. Adductor (Inner Thigh Muscles) Stretch: Feet facing each other, knees outward. Squat, grab both feet, pull towards groin. Hold, relax, repeat.

During operation, the display automatically switches every 5 seconds to show different metrics in sequence: “SPEED”, “TIME”, “DIST” (distance), and “CAL” (calories).

Speed display range: 1.0-4.0mph

Distance display range: 0.00-99.99miles

Time display range: 0:00-99:59

Calorie display range: 0.00-9999 kcal

Within 5 seconds of powering on the treadmill, press and hold the remote control “START/STOP” button. The treadmill will beep three times (“beep-beep-beep”) indicating successful pairing. Re-pairing is not needed after power disconnection unless cancelled.

Press and hold the remote control “+” button. The display will show “0”, and the treadmill will beep three times. After cancellation, any compatible remote of the same model can be paired.

1. In standby mode, press and hold the remote control “-” button.

2. Turn on your phone/device’s Bluetooth and search for “Mobvoi WT Fit”.

3. Tap the name “Mobvoi WT Fit” on your device to connect.

Press and hold the remote control “-” button in standby mode.

Start/Stop:

– Short-press the “START/STOP” button after powering on. Display shows countdown (3333/2222/1111) and beeps (“beep ~”). Treadmill starts.

– Short-press the “START/STOP” button while running to stop. Speed gradually decreases, machine enters standby.

Speed +:

– While running, short-press “+” to increase speed slowly.

– Press and hold “+” to accelerate quickly. Speed increases in 0.2mph increments.

Speed -:

– While running, short-press “-” to decrease speed slowly.

– Press and hold “-” to decelerate quickly. Speed decreases in 0.2mph increments.

Pause:

– While running, short-press the “PAUSE” button. Display shows “PAU”, treadmill pauses, data saved.

– Press “PAUSE” again to resume running.

Buzzer Function:

– Toggles the button beep sound. “OFF” displayed when turned off, “ON” displayed when turned on. All button actions are silent when the buzzer is off.

Yes, the treadmill is compatible with Zwift and Kinomap. These apps are developed by their respective developers. For usage and support, contact the app developer.

Use a smartwatch adopting Wear OS by Google™.

Download and Install Apps:

1. On the watch, open Play Store, search for and install “Mobvoi Treadmill”.

2. On the watch, open Play Store, search for and install “Mobvoi Account”.

Sign In and Connect:

1. Sign in to your Mobvoi account via the Mobvoi Account app on the watch (using watch or phone login options). Register if needed.

2. Ensure the treadmill is on with Bluetooth mode active, and the watch’s Bluetooth is on.

3. Open the Mobvoi Treadmill App on the watch and click “Connect Devices”. It should automatically pair.

During Exercise:

– View real-time exercise data (time, speed, distance, calories, pace) and heart rate on the watch.

– Ensure the treadmill runs at low speed for safety checks.

After Exercise:

– The watch records and generates a sports record.

View History (Mobile App):

1. Download and install the “Mobvoi App” on your phone from the app store and log in.

2. Click the “Sports Card” on the home page to view exercise history synced from the watch.

3. View detailed records and share history.

Issues	Possible Causes	Troubleshooting Steps
Treadmill cannot operate.	Power not connected.	Plug the power cord into the socket.
	Power not turned on.	Turn the power switch to the ON position.
	Circuit signal system malfunction.	Check the controller input and signal lines.
Running belt does not run smoothly.	Insufficient lubrication.	Apply methyl silicone oil lubricant.
Treadmill belt slipping.	Running belt too tight.	Adjust the tightness of the running belt.
	Running belt slips. / Loose belt.	Adjust the tightness of the running belt.

If you have other questions, contact the local dealer or company’s after-sales service.

Fault Codes	Possible Causes	Troubleshooting Steps
E01	Communication abnormality between lower control and electronic board.	Check if the communication cable between the lower control and the electronic board is loose or disconnected.
E02	1. Motor wires are loose or disconnected. 2. Carbon brushes are worn out or not in contact with the rotor. 3. Lower control is damaged.	Inspect the motor wires for looseness or disconnection. If not disconnected, check if the motor brushes are worn out or not in contact with the rotor. If the motor is normal, the lower control may be damaged.
E05	Overload protection activated.	If there is an overload, exceeding the rated current, turn off the power and restart.
E10	Display data reading error	Turn off the power and then on again
E23/E24/E28	Controller hardware abnormality	Wait 10 minutes after powering off and then powering on again.
Display Abnormalities	External interference.	Turn off the power switch, wait for 1 minute, and then power on and restart.

Use the dedicated methyl silicone oil.

Weekly usage less than 3 hours: Lubricate once every 5 months.

Weekly usage between 4-7 hours: Lubricate once every 2 months.

Weekly usage more than 7 hours: Lubricate once every 1 month.

Note: Excessive lubrication is not better.

Lift the treadmill belt and touch the center of the belt’s back with your hand. If your hand feels slightly moist from silicone oil, no lubrication is needed. If the running board is dry and your hand gets no silicone oil, lubrication is required.

1. Stop the walking treadmill.

2. Lift a small portion of the running belt.

3. Spray methyl silicone oil on the inner side of the belt, close to the center.

4. Run the walking pad at 1.0mph to evenly spread the oil.

5. Lightly step on the belt from left to right for a few minutes to ensure complete absorption.

If the belt feels loose or slips during use, it needs adjustment. Using the provided 5# hex wrench, turn the belt adjustment bolts on both sides clockwise synchronously, in half-turn increments. Be careful not to overtighten, as this can increase motor load and cause damage. Adjust until slipping stops but the belt is not excessively tight.

Deviation can occur due to unstable placement, uneven foot pressure, or uneven force application. Often, running without load for a few minutes restores alignment.

If automatic recovery fails, use the 5# hex wrench for manual adjustment:

If the belt deviates to the LEFT: Adjust the LEFT bolt clockwise OR the RIGHT bolt counterclockwise (in gradual half-turn increments).

If the belt deviates to the RIGHT: Adjust the RIGHT bolt clockwise OR the LEFT bolt counterclockwise (in gradual half-turn increments).

Note: Running belt deviation is not covered by warranty. Prompt maintenance is necessary to prevent damage.

Statutory warranty service is provided in the country of purchase. For the electric treadmill (Model N3825D mentioned, likely applicable to TM09), within one year under normal home use, Mobvoi provides free replacement parts for non-human-induced damages. After the warranty period, spare parts are offered at favorable prices.

This product is intended for home use only; issues from commercial use are not covered.

For post-sales issues, contact your local dealer’s after-sales service or customer service at support@mobvoi.com.

Manufacturer: Jiangxi EQi Industrial Co., Ltd.

This device should be installed and operated with a minimum distance of 15cm between the antenna and all persons.

It complies with Part 15 of the FCC Rules for a Class B digital device, designed to provide reasonable protection against harmful interference in a residential installation. It generates, uses, and can radiate radio frequency energy.

If interference with radio/TV reception occurs (check by turning device off/on), try:

– Reorient or relocate the receiving antenna.

– Increase separation between device and receiver.

– Connect device to an outlet on a different circuit from the receiver.

– Consult the dealer or an experienced radio/TV technician.

Changes or modifications not expressly approved by the responsible party could void user authority to operate the equipment.

Operation is subject to two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.