MOBVOI HOME TREADMILL SE T4089 (02) PDF MANUAL

Please read the instruction manual carefully before use and pay attention to the following safety precautions:

★ The treadmill should be placed in a well-ventilated and dry indoor area to avoid moisture. Do not place any foreign objects on the treadmill to prevent motor damage due to water entering the motor.

★ Before starting exercise, ensure you are wearing appropriate sportswear and professional sports shoes, and perform full-body stretching activities. Do not exercise barefoot on the treadmill.

★ The power plug must be securely grounded, and the socket used should have a dedicated circuit to avoid sharing power with other electrical devices.

★ Keep children away from this equipment to prevent accidents.

★ Avoid prolonged operation of the treadmill under overload conditions, as this may lead to damage to the motor and controller, accelerating wear and aging of bearings, running belts, and the deck. Regular maintenance is recommended to ensure the equipment is in good condition.

★ To maintain the normal operation of electronic instruments and controllers, reduce indoor dust, and maintain appropriate indoor humidity to prevent strong electrostatic interference.

★ After use, be sure to turn off the power of the treadmill.

★ Maintain indoor air circulation while using the treadmill.

★ If you feel discomfort or experience abnormal conditions during exercise, stop immediately and consult a medical professional.

★ After using silicone oil, store it in a place inaccessible to children to avoid serious consequences in case of accidental ingestion.

★ The safety area behind the treadmill is 39.37*78.74inch.

★ The method to jump off the treadmill in an emergency is: grasp the handrails with both hands, lift the body, and simultaneously place both feet on the side strips, then jump off the treadmill from one side.

★ Avoid placing the treadmill on a carpet, as this may reduce ventilation and cooling efficiency, leading to potential motor burnt out.

★ Do not place the treadmill on uneven floors, as this may cause imbalance during use and damage the treadmill.

To reduce accidents, please follow these regulations:

★ Before using the treadmill, check if clothing is properly fastened or zipped up.

★ Avoid wearing items that may be caught by the treadmill.

★ Keep the power cord away from heat sources.

★ Prevent children from approaching the treadmill.

★ Do not use the treadmill outdoors.

★ Disconnect the power before moving the treadmill.

★ Do not open the upper cover and left and right rear seats without professional supervise.

★ Restricted to one person exercising on the treadmill.

★ If you feel dizziness, chest pain, nausea, or shortness of breath during exercise, stop immediately and consult a medical professional.

When you are undergoing medical treatment or belong to the following patient types, be sure to consult a professional doctor before using:

(1) Patients experiencing lower back pain or those who have suffered injuries to the legs, lower back, or neck, or those experiencing pain in the legs, lower back, neck, and arms (such as chronic patients with disc herniation, spinal slippage, cervical protrusion, etc.).

(2) Patients with osteoarthritis, rheumatism, or painful rheumatism.

(3) Individuals with abnormalities such as osteoporosis.

(4) Individuals with circulatory system diseases (heart disease, vascular disease, high blood pressure, etc.).

(5) Individuals with respiratory organ disorders.

(6) Individuals using artificial pacemakers or implanted medical electronic devices.

(7) Individuals with malignant tumors.

(8) Individuals with thrombosis or severe blood circulation disorders, acute venous inflammation, etc.

(9) Individuals with peripheral circulation disorders caused by conditions such as diabetes.

(10) Individuals with skin wounds.

(11) Individuals with fever due to diseases (skin temperature reaching 38°C or above).

(12) Individuals with abnormal or bent backs.

(13) Pregnant or potentially pregnant women, or women in menstruation.

(14) Individuals feeling physically abnormal and in need of rest.

(15) Individuals with obvious poor physical condition.

(16) Individuals using the equipment for rehabilitation purposes.

(17) Individuals who feel any abnormality in their body other than the above situations.

Use by these individuals may cause accidents or worsening of physical condition.

If you experience unusual pain, such as lower back pain, leg numbness, dizziness, abnormal heartbeat, or a sense of discomfort different from usual during exercise, stop immediately and consult a medical professional.

◆ Do not allow children to use this product or play around it. Non-compliance with this regulation may lead to injury.

◆ Supervisors of children should be careful not to let them play with this product. Non-compliance with this regulation may result in injury.

During use or when loading and unloading the product, ensure that there are no people or pets around (rear, bottom, front of the product).

◆ Do not use this device if the housing is cracked, broken, or detached (exposing internal structures) or if welded parts are detached. Otherwise, accidents or injuries may occur.

◆ Do not jump on or off the treadmill during exercise. Doing so may cause falls and injuries.

◆ Do not use or store the treadmill outdoors, in the bathroom, or in damp or easily wet places.

◆ Do not place the treadmill in direct sunlight or in a high-temperature environment, such as around a fireplace or on heating devices such as electric blankets. Otherwise, electrical leakage or fire may occur.

◆ If the power cord or power plug is damaged or the socket is loose, do not use the treadmill. Otherwise, electric shock, short circuit, or fire may occur.

◆ Do not damage, bend, or twist the power cord. Also, avoid placing heavy objects on the power cord or pinching the wire. Otherwise, leakage or fire may occur, or even electric shock, short circuit.

◆ Do not let two or more people use the treadmill simultaneously, and be mindful of the absence of others around during use. Otherwise, accidents or injuries may occur.

◆ Do not allow individuals who cannot express their consciousness or operate the treadmill independently to use it. This may result in accidents or injuries.

◆ Absolutely prohibited to disassemble, repair the walking treadmill, or replace the treadmill’s components. There is a risk of injury due to mechanical failure.

◆ Do not allow the main body or control components to come into contact with water or other conductive liquids. This may result in electric shock or fire.

◆ People who do not exercise regularly should not engage in strenuous exercise suddenly. This may cause harm to health.

◆ Do not use after drinking water, feeling fatigued, during the early stages of exercise, or when the body is in an abnormal condition. This may lead to injury.

◆ Do not use during drinking, eating, or other activities.

◆ Do not use when feeling sluggish after drinking. This may cause accidents or injuries.

◆ Do not use with hard objects in the pockets of pants. This may cause accidents or injuries.

◆ Do not allow needles, garbage, or water to attach to the power plug. This may cause electric shock, short circuit, or fire.

◆ Do not pull out the power plug or switch the power switch to “off” during use. This may cause injury.

Do not pull out or insert the power plug with wet hands. This may cause electric shock and injury.

◆ When the equipment is not in use, pull out the power plug from the socket. Dust and humid air may cause insulation degradation, leading to electrical leakage or fire.

◆ When maintaining, be sure to pull out the power plug from the socket. Non-compliance may result in electric shock or injury.

◆ When the equipment cannot start or abnormalities occur, stop using it. Immediately pull out the power plug, and entrust a professional to inspect and repair. Non-compliance may result in electric shock or injury.

◆ During a power outage, pull out the power plug immediately. Otherwise, there may be accidents or injuries when power is restored.

◆ When pulling out the power plug, do not pull the wire portion; grip the plug to pull it out. Otherwise, short circuits, electric shock, or fire may occur.

◆ This product requires grounding. If the equipment malfunctions, grounding will provide the minimum resistance path for current, reducing the risk of electric shock.

◆ The product is equipped with a wire for grounding the device and a grounding plug. This plug must be inserted into a properly installed and grounded socket that fully complies with local regulations or legal requirements.

◆ Improper connection of the grounding conductor of the device may result in an electric shock hazard. If you have any doubts about the grounding of the product, please entrust a professional electrician for inspection. Even if the plug provided with the equipment does not match the socket, do not modify it.

◆ Please have a professional electrician install the appropriate socket.

◆ This product has a grounding plug. Ensure it is connected to a socket that matches its plug shape.

◆ This product cannot be plugged into an adapter.

NO.	Name	Qty.	Remarks
1	Main Unit	1
2	Spare Parts Package	1	See attached table (in Spare Parts Package List)

Working Voltage	AC 110V 60Hz
Maximum Load	265LBS
Product Dimensions	48.78″x27″x44.64″
Folded Dimensions	55″x27″x8.27″
Running Area	15.7″x39.4″
Maximum Power	2.5HP
Displayed Speed	0.6-7.6mph
Control Method	Remote control, electronic display

NO.	Name	Qty.	Remarks
1	5# Inner Hexagonal Wrench	1	Miscellaneous
2	6# Inner Hexagonal Wrench	1	Adjustment of Running Belt
3	Adjustable Wrench	1
4	Socket Wrench	1
5	Step Bolt	2
6	Wave Washer	4
7	Left and Right Handles	1 each
8	Handle Round Plug	2
9	Flat Bracket	1
10	Power Cord	1
11	Remote Control	1
12	Safety Lock	1
13	Methyl Silicone Oil	1
14	Manual, Certificate of Conformity	1

1. Place the main unit on the floor after unpacking. Break the “foldable handle” in the direction shown, and the lower end of the column will naturally open to both sides.

2. Lift the column up to the upper limit position.

3. Press down on the “foldable handle” to lock the column.

4. Align the flat bracket (D) with the installation on the control panel.

5. Have the red safety lock (E) sucked into the yellow position under the control panel.

6. When using the treadmill, clip one end of the safety lock to the edge of your clothing.

1. Insert the left handrail (F) into the corresponding position of the left column.

2. Use the (G) step bolt through the (I) waveform washer to tighten the left handle to the column.

3. Use the (H) round plug to tighten the handrail screw hole.

4. The right-hand handle is installed in the same way; please distinguish between the left and right handles when installing.

5. After installing the left and right handles, rotate clockwise or counterclockwise to the limit position to fold or unfold the handles.

Insert the power cord into the front socket of the treadmill, turn on the power switch at the bottom front of the machine, and the treadmill enters standby mode.

If the ground is uneven or the treadmill is shaking, please adjust the adjustable feet at the bottom center and the end of the treadmill to the right position, the feet must fit the ground.

1. To increase the slope: Install the foot pads in the position under the treadmill as shown in the first diagram. This increases the angle between the treadmill and the ground.

2. To decrease the slope: Remove the original foot pads and install them in the screw holes in the position shown in the second diagram (closer to the front). This decreases the angle between the treadmill and the ground.

The machine is shipped with this part adjusted to a slightly appropriate tension, but you can adjust it based on your preference. Avoid loosening too much, as it can cause shaking.

1. Pry out the plug at the lower end of the left column.

2. Combine the hexagonal socket wrench and socket wrench into a lever.

3. Insert the hexagonal head end of the socket wrench into the hole at the lower end of the left column and match it with the hexagonal screw.

4. Rotate clockwise to tighten, and counterclockwise to slightly loosen.

Warm-up: Before each session, a 5-10 minute warm-up is necessary.

Breathing: During exercise, do not hold your breath. Breathe regularly, coordinating with your movements. If breathing becomes too rapid, stop exercising immediately.

Frequency: Training the same muscle group should have a 48-hour rest period, meaning the same muscle group should not be trained on consecutive days.

Training Load: Determine the training load based on personal fitness level, then practice following the principle of progressive load. Muscle soreness is normal in the initial training. With consistent exercise, soreness will gradually subside.

Relaxation: Perform a 5-minute cool-down after each training session, especially stretching and relaxing the muscles in the feet to prevent prolonged tension and maintain muscle elasticity.

Diet and Hydration: It is recommended to exercise at least one hour after a meal, and avoid consuming food immediately after exercise. Drink water sparingly during exercise, especially avoiding large quantities to prevent stress on the heart and kidneys.

It’s advisable to start with stretching exercises before using the treadmill. Warmed up muscles are more flexible, so spend 5-10 minutes warming up. Perform the following stretching exercises – 5 times, 10 seconds or more for each leg; repeat this exercise after walking on the treadmill.

1. Forward Stretch: Bend both knees slightly, lean forward slowly, allowing the back and shoulders to relax. Try to touch your toes with your hands. Hold for 10-15 seconds, then relax. Repeat 3 times.

2. Achilles Tendon Stretch: Sit on a clean mat with one leg straight. Bring the other leg inward, pressing it against the inner side of the straight leg. Try to touch your toes with your hands. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg.

3. Calf and Heel Tendon Stretch: Stand with both hands against the wall, with one foot at the back. Keep the back leg straight and the heel on the ground, lean towards the wall. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg.

4. Quadriceps Stretch: Hold onto the wall or table for balance with the left hand, then extend the right hand backward, grabbing the right ankle and slowly pulling it towards the buttocks until you feel tension in the front of the thigh. Hold for 10-15 seconds, then relax. Repeat 3 times for each leg.

5. Adductor (Inner Thigh Muscles) Stretch: Feet facing each other, knees outward. Squat down, grabbing both feet and pulling towards the groin. Hold for 10-15 seconds, then relax. Repeat 3 times.

The display shows the countdown (“3”, “2”, “1”) when starting. During operation, it automatically switches every 5 seconds to different display sections in the sequence: “SPEED”, “TIME”, “DIST”, and “CAL”.

Display Metrics Ranges:

Setting Parameters	Initial Value	Display Range
Time (min:sec)	0:00	0:00-99:59
Speed (mph)	0.6	0.6-7.6
Distance (miles)	0.00	0.00-99.99
Calories (kcal)	0.0	0.0-9999

When the safety lock is in the detached state, press and hold the Start/Stop (“I▶”) button on the remote control. When you hear continuous beeping sounds from the treadmill buzzer, it indicates successful pairing. You can then start using the remote control to operate the treadmill. Once paired, subsequent usage does not require re-pairing.

1. Start/Stop: In standby mode, press the “Start/Stop” button (I▶). The treadmill will start a 3-second countdown and operate at 0.6mph. During exercise, you can press the “Start/Stop” button at any time to stop the motor.

2. Speed Increase (+): While running, a short press on the “+” button increases speed gradually. A long press increases speed rapidly. Speed increases continuously with an increment of 0.2mph.

3. Speed Decrease (-): While running, a short press on the “-” button decreases speed gradually. A long press decreases speed rapidly. Speed decreases continuously with a decrement of 0.2mph.

The console has the following buttons: “Speed-“, “3”, “Start/Pause”, “Stop”, “6”, “Speed+”.

A. “Start/Pause” Button (I▶): In standby mode, press to start the treadmill. In running mode, press to pause. (Note: After pausing, display shows “PAU”; resume starts countdown 3333, 2222, 1111, returning to minimum speed.)

B. “SPEED-“: Short press for slow deceleration, long press for rapid deceleration. Speed decreases continuously (decrement 0.2mph).

C. “SPEED+”: Short press for slow acceleration, long press for rapid acceleration. Speed increases continuously (increment 0.2mph).

D. 3: Speed shortcut key “3” (sets speed to 3 mph).

E. 6: Speed shortcut key “6” (sets speed to 6 mph).

F. Stop Button: In running or paused state, press to end treadmill operation.

Removing the safety lock in any state will show error code “E07” on the display. If the treadmill is running, removing the safety lock will cause an emergency stop. No operations can be performed with the safety lock removed from the treadmill. Always clip one end of the safety lock to your clothing during use.

The machine has walking and running modes:

Walking Mode: In the folded position (column parallel to the treadmill), the speed range is 0.6-3.8mph.

Running Mode: In the unfolded position (column upright), the speed range is 0.6-7.6mph.

1. On your Wear OS smartwatch, open the Play Store.

2. Search for and install the “Mobvoi Treadmill” app.

3. Search for and install the “Mobvoi Account” app.

4. Open the Mobvoi Treadmill app on the watch and sign in to your Mobvoi account (using watch or phone). If you don’t have an account, register following the tips.

5. Ensure the treadmill is powered on (in Bluetooth mode) and your smartwatch’s Bluetooth is activated.

6. Open the Mobvoi Treadmill app on your smartwatch, select “Connect Devices.”

7. The watch should automatically pair with the treadmill. Confirm the successful connection.

Once connected, you can:

1. View real-time exercise data (heart rate, duration, speed, distance, calories, pace) on your smartwatch.

2. Monitor your data during the workout. Maintain a low-speed setting on the treadmill for personal safety while interacting with the watch.

3. At the end of your session, the smartwatch will record and generate a comprehensive sports record.

1. Search for the “Mobvoi Health” app in your phone’s app store, download, and install it.

2. Log in to your Mobvoi account (the same one used on the watch).

3. Your smartwatch data will sync to the Mobvoi Health app.

4. Navigate to the “Sports Card” on the home page to review your exercise history from the Mobvoi Treadmill app.

5. In the Mobvoi Health app, access detailed data records and share your exercise history with others.

Issues	Possible Causes	Troubleshooting Steps
Treadmill cannot operate	Power not connected.	Plug the power cord into the socket.
	Power not turned on.	Turn the power switch to the ON position.
	Circuit signal system malfunction.	Check the controller input and signal lines.
Running belt does not run smoothly	Insufficient lubrication.	Apply methyl silicone oil lubricant.
	Running belt too tight.	Adjust the tightness of the running belt.
Treadmill belt slipping	Running belt slips.	Adjust the tightness of the running belt.
	Loose belt.	Adjust the tightness of the running belt.

Fault Codes	Possible Causes	Troubleshooting Steps
E01	Communication abnormality between lower control and electronic board.	Check if the communication cable between the lower control and the electronic board is loose or disconnected.
E02	1. Motor wires are loose or disconnected. 2. Carbon brushes are worn out or not in contact with the rotor. 3. Lower control is damaged.	Inspect the motor wires for looseness or disconnection. If not disconnected, check if the motor brushes are worn out or not in contact with the rotor. If the motor is normal, the lower control may be damaged.
E05	Overload protection activated.	If there is an overload, exceeding the rated current, turn off the power and restart.
E07	Safety lock not engaged.	Check if the safety lock is not engaged or if the safety lock wire is loose.
E08	Communication abnormality between upper and lower tables.	Check if the communication line connecting the upper table to the lower table is loose or disconnected.
Display Abnormalities	External interference.	Turn off the power switch, wait for 1 minute, and then power on and restart.

Lubricate with the dedicated methyl silicone oil based on usage:

★ Weekly usage less than 3 hours: Lubricate once every 5 months

★ Weekly usage between 4-7 hours: Lubricate once every 2 months

★ Weekly usage more than 7 hours: Lubricate once every 1 month

Remember: Excessive lubrication is not better. Proper lubrication is crucial.

Lift the treadmill belt and touch the center of the belt’s back with your hand. If your hand has a slight moist feeling from silicone oil, no lubrication is needed. If the running board is dry and your hand doesn’t get any silicone oil, lubrication is required.

★ Stop the walking treadmill running.

★ Lift a small portion of the running belt and spray methyl silicone oil on the inner side of the belt, close to the center.

★ Run the walking pad at 0.6mph to evenly spread the oil across the running board. Lightly step on the belt from left to right. This process takes a few minutes to ensure complete absorption.

All treadmills should be adjusted before leaving the factory and after setup. However, the belt may loosen with use. If you experience slipping, the belt needs adjustment. Turn the belt adjustment bolts (at the rear of the treadmill) clockwise, in half-turn increments, synchronously on both sides using the provided hex wrench. If the belt is too loose, slipping may occur. However, being too tight can increase the load on the motor and damage components. Adjust only enough to prevent slipping.

Belt deviation can occur due to unstable placement, uneven foot pressure, or uneven force applied. Running without load for a few minutes might restore normal operation.

If automatic recovery isn’t possible, use the provided 6# hex wrench to adjust gradually in half-turn increments:

• If the belt deviates to the left: Adjust the left bolt clockwise OR the right bolt counterclockwise.

• If the belt deviates to the right: Adjust the right bolt clockwise OR the left bolt counterclockwise.

Note: Running belt deviation is not covered by the warranty. Perform maintenance according to the manual. Prompt detection and correction are necessary to prevent serious damage.

We provide statutory warranty service in the country where you purchased the product. For the electric treadmill (Model T4089), under normal use within one year, we will provide users with free replacement parts for non-human-induced damages. After the warranty period, spare parts will be provided at favorable prices.

This product is intended for home use only. We are not responsible for issues arising from commercial use. For post-sales issues, contact your local dealer’s after-sales service or Mobvoi customer service: support@mobvoi.com.

Regulatory compliance and full-text Supplier DoC are available on the official website: http://www.mobvoi.com/products.

This device has been tested. This device should be installed and operated with a minimum distance of 15cm between the antenna and all persons.

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the device and receiver.

– Connect the device into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.