MIO CYCLO 100 N411 (01) PDF Document

The MIO CYCLO 100 N411 has four primary buttons with different functions depending on the context:

1. POWER / LIGHT / BACK

• Press and hold for 2 seconds to turn your device on or off.

• When the device is on and in the DASHBOARD menu, press to switch the backlight on or off.

• While navigating menus (except DASHBOARD), press to return to the previous screen.

2. MENU / ENTER

• In the DASHBOARD menu, press to switch between the different screens. Press and hold for 2 seconds to return to the Main menu.

• While in a menu screen or option list, press to select the desired function or option.

3. UP / START|STOP

• Press to scroll up in a menu screen or option list.

• In the DASHBOARD menu, press to select CONTINUE, PAUSE, or STOP the timer during training.

4. DOWN / LAP

• Press to scroll down in a menu screen or in the option list.

• In the DASHBOARD menu, press to create a lap while the timer is counting during training.

Your MIO CYCLO 100 N411 has an internal battery that you should charge for at least 3.5 hours before first use. You can charge it in two ways:

Using a mains power socket:

Plug the home charger cable into the Mini-USB connector on the back of your device and plug the mains power charger into a power socket.

Via a computer:

Connect your device to a computer using the provided USB cable. The mini-USB end connects to your device, and the other end connects to a USB port on your computer.

For optimal performance and longevity of the lithium battery, follow these guidelines:

• Do not charge the battery where the temperature is high (e.g., in direct sunlight). The battery stops charging if the ambient temperature is below -10°C (14°F) or above 60°C (140°F).

• Recharge the battery when it is nearly discharged. Always ensure the battery is fully charged when recharging to extend its life.

• If you will not use the product for over a month, fully discharge the battery before recharging it. It is also advised to fully discharge and recharge the battery once every 1 to 2 months of non-use.

• Failure to follow these instructions could cause damage to your device and battery and may void the warranty.

1. Mount the device and any accessories onto your bike.

2. Press and hold the POWER button for 2 seconds to turn the device on.

3. Follow the on-screen prompts to personalize your device. This includes:

• Selecting your preferred language.

• Selecting the coordinate format (degree or degree/minute/second).

• Selecting the units format (imperial or metric).

• Setting up the date and time format, including time zone and daylight saving.

• Setting up your user profile, including gender, birthday, weight, height, and workout level.

• Selecting your bike type (race, city, or mountain) and completing the bike’s data (weight and wheel size, for selected models).

4. Once turned on, the device will automatically search for satellite signals. When GPS is fixed, the GPS signal icon will appear on the screen.

5. Depending on your model, you may need to pair sensors like a heart rate monitor or cadence/speed sensor. Enable the device to scan for them from Main menu > SETTINGS > ACCESSORIES > SENSORS.

1. Turn on your computer.

2. Turn on your MIO CYCLO 100 N411.

3. Connect the mini-USB end of the USB cable to the back of your device and the other end to a USB port on your computer.

4. When the “CONNECT TO PC?” message appears on your device screen, select your desired connection type:

• YES: Your device will connect to the computer, allowing you to transfer training data and upgrade your device via Mio Share (when an update is available).

• NO: You will be able to continue using your device while the battery charges via the computer.

1. Select the rubber pad from the bike mount kit that best fits the handlebars on your bike.

2. Attach the rubber pad and bike mount to the handlebars using the two provided plastic straps.

3. Align the latch on the back of the MIO CYCLO 100 N411 with the slot on the bike mount.

4. Rotate the device clockwise to lock it into place on the mount.

5. To remove the device, rotate it anticlockwise.

1. Attach the main sensor unit to the chainstay of your bike using the provided ties.

2. Attach the speed magnet to a spoke on the rear wheel, ensuring it aligns with the speed sensor arm.

3. Attach the cadence magnet to the inner side of the crank arm, ensuring it aligns with the main body of the sensor.

4. Ensure the distance between the magnets and the corresponding sensor areas is between 3 to 5 mm.

5. After installation, you must pair the sensor with your device. Go to Main menu > SETTINGS > ACCESSORIES > SENSORS and select SPEED, CADENCE, or SPEED/CADENCE and then SCAN to pair.

1. Before use, wet the contacts on the back of the chest strap with water. You can also use an electrolyte gel for better contact.

2. Adjust the elastic strap so it is snug around your lower chest, but not so tight that it restricts breathing.

3. Wrap the strap around your back and secure it on the other side with the buckle.

4. Once you are wearing the monitor, you must pair it with your device. Go to Main menu > SETTINGS > ACCESSORIES > SENSORS, select HEART RATE, and then select SCAN to pair.

Both the cadence/speed sensor and the heart rate monitor use a replaceable CR2032 battery. The replacement process is similar for both:

1. Locate the battery cover on the back of the sensor or monitor.

2. Use a coin to twist the cover anticlockwise to remove it.

3. Remove the old battery and insert the new CR2032 battery into the battery chamber.

4. Replace the cover and use a coin to twist it clockwise to close and secure it.

The Main menu provides access to the primary functions of your device:

• DASHBOARD: Displays various screens including date and time, compass (on selected models), and workout data screens.

• WORKOUT: Lets you set up and start workouts based on conditions like distance, time, or speed.

• HISTORY: Allows you to review past training data such as date/time, distance, speed, and altitude.

• SETTINGS: Provides options to customize system settings, user profiles, sensor settings, and more.

• TO PC: Allows you to transfer your training data from the device to a computer.

The DASHBOARD provides multiple screens with training data. The layout of these screens can be customized.

• To access the DASHBOARD screens, select DASHBOARD from the Main menu.

• To cycle through the different DASHBOARD screens (e.g., Custom 1, Custom 2, Time, Compass), press the ENTER button continuously.

• To return to the Main menu from any DASHBOARD screen, press and hold the ENTER button for 2 seconds.

To learn how to customize the DASHBOARD screens, see the “PAGE SETTINGS” section in the device settings.

To start a workout, select WORKOUT from the Main menu. You can set workouts based on different conditions:

• DIST/TIME: Enter the DTG (distance to go) and TTG (time to go) settings and then select START.

• DIST/SPEED: Enter the DTG (distance to go) and SPEED settings and then select START.

• SPEED/TIME: Enter the TTG (time to go) and SPEED settings and then select START.

• MY RECORDS: This lists previous workouts. You can select a past workout and press ENTER to select START to compete against that record.

Once a workout starts, the device will analyze and report your status on the DASHBOARD screens.

To view your saved trainings and workouts, select HISTORY from the Main menu.

Select LIST ALL to see all recorded activities. Select a specific activity from the list to view its details, including date, time, total distance, calories burned, total time, and average/fastest records.

Once you select an activity, you have several options:

• TRACK: View the route of the training/workout on a map. Press ENTER again to view diagrams of speed, heart rate, or cadence (for selected models).

• REPEAT: Track back to the start point (BACKWARD) or to the end point (FORWARD) of the route.

• LAPS: View the lap details on the map screen.

• DELETE: Delete the selected history data.

You can also select DELETE ALL from the initial HISTORY screen to erase all saved data.

To access the customization options, select SETTINGS from the Main menu.

• Use the UP/DOWN button to scroll through the menu items (e.g., ACCESSORIES, ALERTS, AUTO LAP, etc.). The selected item will be highlighted.

• Press ENTER to access the settings for the highlighted item.

• Within a setting, use the UP/DOWN button to select the desired option and press ENTER to confirm.

• Press the BACK button to return to the previous page.

In the SETTINGS menu, select ALERTS. You can configure the following:

• TIME/DIST: Set an alarm to sound when a specified time or distance is reached. You can set it to sound ONCE or REPEAT. Select OFF to disable.

• SPEED: Set an alarm to sound when your speed goes above a maximum value or below a minimum value. Select OFF to disable.

• HEART RATE: Set an alarm to sound when your heart rate is above or below your custom or HR ZONE setting. Select OFF to disable.

• CADENCE: Set an alarm to sound when your cadence is above or below a setting value. Select OFF to disable.

• SETTINGS: Choose the alert method as MESSAGE/BEEPER or SYMBOL/BEEPER.

The AUTO PAUSE function automatically pauses the training timer when you stop moving or your speed falls below a certain value. This ensures that the average speed and calorie calculations are more accurate. You can configure this in SETTINGS > AUTO PAUSE.

• WHEN STOPPED: The timer pauses automatically when you stop moving.

• CUSTOM SPEED: Set a specific speed below which the timer will pause.

• OFF: Disables the Auto Pause function.

Compass Calibration (SETTINGS > COMPASS):

1. Select CALIBRATION.

2. Follow the on-screen instruction to rotate the device 360 degrees to complete the calibration.

3. Keep the device away from objects that generate magnetic fields during calibration.

Barometer Calibration (SETTINGS > BAROMETER):

To get an accurate altitude reading, you should calibrate the barometer before a training session.

• AUTO: (Default) The system calibrates the sensor using the GPS signal when it is reliable.

• MANUAL: Manually input the current Sea Level Pressure (S.L. PRESSURE) from an official weather source. The device will then display the current altitude based on this value.

To restore your device to its factory default status, go to SETTINGS > FACTORY RESET. Select YES to confirm.

Warning: Performing a factory reset will erase all training data and your user profile.

You can set the time interval for recording data points by going to SETTINGS > RECORDED DATA. In the TO RECORD AT field, you have two options:

• EVERY SECOND: The system is set to record one data point every second. This creates the most accurate record for your training.

• CUSTOM TIME: You can manually set the time interval. The recommended values are:

– walking and running: 1 sec

– cycling: 2 sec

Go to SETTINGS > SYSTEM to customize various system-level options.

• BEEPER: Enable the beeper for MESSAGE ONLY or both KEY AND MESSAGE. Select OFF to disable.

• DISPLAY:

– BACKLIGHT: Set the backlight to stay on (STAYS ON) or turn off automatically after 15 SECONDS, 30 SECONDS, 1 MINUTE, or 2 MINUTES.

– LANGUAGE: Select the preferred language for menus.

– ORIENTATION: Set the screen orientation to PORTRAIT or LANDSCAPE.

– UNITS: Set measurement units to IMPERIAL (ft, mph) or METRIC (m, kph). You can also set the COORDINATE FORMAT.

• TIME:

– TIME FORMAT: Set the display to 12 HOUR or 24 HOUR.

– TIME ZONE: Select your local time zone.

– DAYLIGHT SAVING: Select if daylight saving is active.

• ALARM: Set the alarm clock frequency (e.g., DAILY, WEEKDAY) and the alarm time.

Taking good care of your MIO CYCLO 100 N411 will ensure trouble-free operation:

• Keep the device away from excessive moisture and extreme temperatures.

• Avoid exposing it to direct sunlight or strong ultraviolet light for extended periods.

• Do not place anything on top of your device, drop it, or subject it to severe shock.

• Avoid sudden temperature changes, which can cause internal moisture condensation. If this occurs, allow the device to dry out completely before use.

• The screen surface can be scratched. Avoid touching it with sharp objects.

• Never clean your device when it is turned on. Use a soft, lint-free cloth to wipe the screen and exterior. Do not use paper towels.

• Never attempt to disassemble, repair, or modify the device.

• Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as your device.

The remaining battery power may be too low to run your MIO CYCLO 100 N411. Charge the battery for at least 3.5 hours.

If the screen responds slowly, make sure that your device is not running out of battery power. If the problem still persists, reset your MIO CYCLO 100 N411.

If the screen freezes completely, restart your device.

Make sure that the backlight of the display is set to a high-enough brightness. You can adjust this in SETTINGS > SYSTEM > DISPLAY > BACKLIGHT.

If you are having trouble connecting to a computer, try the following steps:

• Make sure that both your MIO CYCLO 100 N411 and your computer are turned on before trying to connect.

• Make sure the USB cable is securely plugged into the USB port on your computer and into your device.

• Connect the USB cable directly to your computer’s USB port; do not use a USB hub.

• Reset your MIO CYCLO 100 N411 before connecting the cable. Always disconnect your device before you restart your computer.