MILWAUKEE TICK ONET (01) PDF DOCUMENT

Always read and understand all instructions before using the MILWAUKEE TICK ONET. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

1. SAVE THESE INSTRUCTIONS-THIS OPERATOR’S MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS.

2. THIS DEVICE IS DESIGNED TO BE POWERED BY (1) CR2032 BATTERY PROPERLY INSERTED. Do not attempt to use with any other voltage or power supply.

3. CHEMICAL BURN HAZARD. KEEP BATTERIES AWAY FROM CHILDREN.

4. THIS DEVICE CONTAINS A LITHIUM BUTTON/COIN CELL BATTERY. A NEW OR USED BATTERY CAN CAUSE SEVERE INTERNAL BURNS AND LEAD TO DEATH IN AS LITTLE AS 2 HOURS IF SWALLOWED OR ENTERS THE BODY. Always secure the battery cover. If it does not close securely, stop using the device, remove the batteries, and keep it away from children. If you think batteries may have been swallowed or entered the body, seek immediate medical attention.

5. INSTALL BATTERY ACCORDING TO POLARITY (+/-) DIAGRAMS.

6. PROPERLY DISPOSE OF USED BATTERIES IMMEDIATELY.

7. DO NO INCINERATE OR DISMANTLE BATTERIES.

8. UNDER ABUSIVE CONDITIONS, LIQUID MAY BE EJECTED FROM THE BATTERY, AVOID CONTACT. IF CONTACT ACCIDENTALLY OCCURS, FLUSH WITH WATER. IF LIQUID CONTACTS EYES, ADDITIONALLY SEEK MEDICAL HELP. Liquid ejected from the battery may cause irritation or burns.

9. DO NOT DISPOSE OF DEVICE OR BATTERIES TOGETHER WITH HOUSEHOLD WASTE MATERIAL! Appliance and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.

Before first use, remove the plastic tab from between the battery and contacts. Discard the plastic tab and replace the cap. Remove the clear protective backing from the back of the MILWAUKEE TICK ONET.

To activate the MILWAUKEE TICK ONET, follow these steps:

1. Download ONE-KEY app and log in.

2. Remove protective cover from battery and back of TICK.

3. Add or select item from app inventory.

4. Tap ASSOCIATE TICK button in app and follow steps to activate TICK.

5. Attach TICK to item and start tracking.

1. To download the ONE-KEY app, visit the App Store or Google Play from your smart device.

2. Create a Username and Password and log in to a ONE-KEY account.

3. Bluetooth and Location Services must be enabled on the mobile device.

4. Location Services must be enabled in the Settings section of the App.

1. Select or add a new item in “Inventory” to be tracked using the MILWAUKEE TICK ONET.

2. Select the red “Associate Tick” button on the Inventory Item Detail screen.

3. Follow the instructions on the screen.

4. Select “Start Scan”. The App will scan for TICKs in range. If there are too many in range, move the others at least 90cm away.

5. Once the App has paired a MILWAUKEE TICK ONET with the Inventory Item, tracking can begin.

NOTE: If the device receives a sharp blow or impact, it may need to be paired again.

If the MILWAUKEE TICK ONET will not be used for a long time, remove the battery as a protection against corrosion.

1. Open the MILWAUKEE TICK ONET Tracking Device by rotating the cover.

2. Remove the CR2032 coincell battery.

3. Remove the clear protective film (first time only).

4. Replace the CR2032 coincell battery, positive (+) side up.

5. Replace cover and rotate to lock.

6. Remove the clear protective backing on the bottom of the Tick (first time only).

The MILWAUKEE TICK ONET is designed to track tools and equipment using the ONE-KEY App. It will not prevent theft from happening. The MILWAUKEE TICK ONET can be installed in a variety of orientations. Consider installing it to prevent tampering. Be sure the battery door can be removed once installed.

The MILWAUKEE TICK ONET can be installed using the following attachment options:

• #8 Pan Head Self Tapping Screw

• 5/32 Diameter Rivet

• Cable or Zip Tie

• Glue or Epoxy

• Adhesive Backing

• Keyring

WARNING! Do not secure in such a way as to impede the safe use of the product.

Before using screws or rivets, ensure the space behind the placement is clear.

Do not attach the MILWAUKEE TICK ONET on or near the following:

• vents

• safety notifications

• hand holds

• areas exposed to sparks or heat

• moving parts

• guards

• switches or controls

• Clean the MILWAUKEE TICK ONET with a damp, soft cloth.

• Never use aggressive cleaning agents or solvents.