MILWAUKEE M12 AXIS AHJBLK (01) PDF Document

NOTE: The MILWAUKEE® heated jacket is compatible with other designated 12 V MILWAUKEE® heated gear controllers and power supplies.

The main components of the heated jacket are:

1. Chest and back temp control panel with LEDs

2. Shoulders temp control panel with LEDs

3. Power buttons

4. Power cable

5. Battery controller pocket

Inserting the Battery:

1. To insert the battery, slide the pack into the body of the battery holder. Make sure it latches securely into place.

2. Insert the power cable (from inside the pocket) into the power cable port on the battery holder.

3. Push the power cable completely into the battery holder pocket and zip all pockets closed.

Removing the Battery:

To remove the battery, push in the release buttons and pull the battery pack away from the holder.

Always remove the battery pack any time the jacket is not in use.

The heated jacket has two heating zones: the primary zone (chest and back area) and the secondary zone (shoulders area).

To Turn On:

Press and hold (about 2 seconds) the power button on the corresponding side of the control panel for the zone you wish to heat. The LEDs on that side will turn on, and the zone will be set to maximum heat.

To Cycle Through Heat Levels:

Press the corresponding power button for the desired zone. Each press will cycle through medium, low, and back to maximum heat.

To Turn Off:

Press and hold (about 2 seconds) the power button on the corresponding side of the control panel. The LEDs for that zone will turn off.

The applicable heat setting is indicated by the number of LEDs illuminated:

1 LED = Low Heat

2 LEDs = Medium Heat

3 LEDs = High Heat

WARNING: To reduce the risk of personal injury and damage, disconnect and remove the battery pack and battery holder from the battery holder pocket before washing. Never immerse your battery holder, battery pack, or charger in liquid or allow a liquid to flow inside them.

To clean the heated jacket:

1. Remove the battery pack and holder.

2. Push the power cord completely into the battery holder pocket and fasten it closed. Zip the centre front zipper closed before washing.

3. Hand wash, very mild process at a max 30°C. Do not use bleach. Do not dry clean. Do not wring or twist.

4. Tumble Dry on Low Heat. Do not iron.

General Care:

• Before storing, disconnect and remove the battery pack and battery holder from the pocket.

• Follow Care Instructions on the jacket tags.

• Maintain the heated gear. Check for breakage of parts and any other condition that may affect its operation. If damaged, have the heated gear repaired before use.

• When storing the appliance, allow it to cool down before folding.

If the heated jacket turns off unexpectedly, check connections and charge the battery pack. The battery holder is located inside of the pocket.

If the heated jacket does not start or operate properly with a fully charged battery pack, clean the contacts on the battery pack. If the heated jacket still does not work properly, return the heated jacket, charger, and battery pack to a MILWAUKEE® service facility for repairs.

If improper operation of the heated jacket is observed, discontinue its use immediately and contact a MILWAUKEE® service facility for repair.

Read instructions carefully.

Use:

• Do not use this heated jacket with an infant, child, a helpless person, or anyone insensitive to heat, such as a person with poor blood circulation.

• If you have a medical condition making you sensitive to overheating, or you use any personal medical devices, consult the device manufacturer and/or your physician to determine if use of this product is appropriate.

• Never use if the inner liner is wet.

• Heating elements are not recommended to touch bare skin.

• Shut off power immediately if discomfort occurs.

• Do not allow the cords to be pinched.

• For continuous use, set the temperature settings on the low mode.

• Examine the appliance frequently for signs of wear or damage. If there are such signs, or the appliance has been misused or does not work, return it to the supplier before switching it on again.

• Do not insert pins. They may damage the electric wiring.

CAUTION: Risk of fire or explosion if the battery is replaced by an incorrect type.

• Recharge only with the charger specified by the manufacturer.

• Use the heated gear only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

• When the battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

• Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

• Do not charge non-rechargeable batteries.

• To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

• Do not dispose of a battery into fire or a hot oven, or mechanically crush or cut a battery, as that can result in an explosion.