MAGIC CHEF HMDR1000SE (01) PDF Document

Before using your new MAGIC CHEF HMDR1000SE, please follow these initial steps:

1. Remove all exterior and interior packing materials.

2. Before connecting the refrigerator to a power source, allow it to stand upright for approximately 4 hours. This helps reduce the possibility of a malfunction in the cooling system that could occur from improper handling during transportation.

3. Clean the interior surface of the refrigerator with lukewarm water using a soft cloth.

For proper installation of your MAGIC CHEF HMDR1000SE, follow these guidelines:

• This appliance is designed to be free-standing only and should not be recessed or built-in.

• Place the refrigerator on a floor strong enough to support it when fully loaded.

• Allow 5 inches of space between the back and sides of the refrigerator to ensure proper air ventilation. Adjust the leveling feet to keep the refrigerator level.

• Position the refrigerator away from direct sunlight and sources of heat such as stoves, heaters, or radiators. Direct sunlight can affect the acrylic coating, and heat sources can increase electrical consumption.

• Ambient temperatures below 50°F (10°C) or above 85°F (29.4°C) will hinder the performance of this appliance. This unit is not designed for use in a garage or any other outside installation.

• Avoid placing the refrigerator in moist areas.

• Plug the refrigerator into a dedicated, properly installed-grounded wall outlet. This unit is not designed to be installed in an RV or used with an inverter.

• After plugging the appliance in, turn it on and allow it to cool down for 2 to 3 hours before placing food in the refrigerator or freezer compartment.

Improper use of the grounded plug can result in the risk of electrical shock. Your MAGIC CHEF HMDR1000SE has the following electrical requirements:

• The refrigerator should be properly grounded for your safety. The power cord is equipped with a three-prong plug that mates with standard three-prong wall outlets to minimize the possibility of electrical shock.

• Do not, under any circumstances, cut or remove the third (ground) prong from the supplied power cord.

• This refrigerator requires a standard 115 Volt A.C. ~/60Hz electrical outlet with a three-prong ground.

• This appliance is not designed to be used with an inverter.

• The power cord should be secured behind the refrigerator and not left exposed or dangling to prevent accidental injury.

• Never unplug the refrigerator by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle.

• Do not use an extension cord with this appliance. If the power cord is too short, have a qualified electrician or service technician install an outlet near the appliance.

Your MAGIC CHEF HMDR1000SE has two temperature controls:

1. Refrigerator Temperature Control: Located on the top of the refrigerator compartment, this panel controls the actual cooling cycle. It has settings for OFF, COLD, COLDER, and COLDEST, with a RECOMMENDED setting indicated. You can press and hold the “SET” button for 3 seconds to turn off all cooling functions without cutting power to the unit.

2. Freezer Control: This is a control knob inside the freezer compartment that adjusts the distribution of cold air between the freezer and refrigerator. It has settings for COLD, COLDER, and COLDEST, with a RECOMMENDED position marked.

When you first turn the unit on, adjust the temperature control knob in the freezer compartment to “COLDEST” and the temperature control in the refrigerator compartment to “COLDEST”. Let the appliance run for at least 4 hours before placing food inside. Afterward, return the freezer selector to the “Recommended” or “COLDER” position and the refrigerator selector to the “Recommended” or “COLDER” position. The setting of “Recommended” in the refrigerator and “COLDER” in the freezer is appropriate for most home or office use as it distributes cold air equally.

You can adjust the balance of cold air using the control knob in the freezer:

• To direct more cold air to the freezer (e.g., after adding a large amount of food), move the freezer controller to the “COLDEST” position. Once the desired temperature is reached, return the controller to the “Recommended” position.

• To direct more cold air to the refrigerator section (e.g., to cool down fresh food quickly), move the freezer controller to the “COLD” position. Once the desired temperature is reached, return the controller to the “Recommended” position.

To ensure the quality of frozen foods, follow these guidelines:

• The freezer compartment is designed for the long-term storage of frozen food.

• Place commercially pre-packed frozen food into the freezer as quickly as possible after purchase, following the manufacturer’s storage time instructions.

• Select food of adequate quality that is suitable for freezing.

• Use correct packaging and wrap it tightly. The packaging should be airtight and not leak to prevent vitamin loss and dehydration.

• Foils and bags should be soft enough to wrap tightly around the foods.

• When preparing foods to be frozen, consider sanitary precautions.

• Mark packages with the kind and amount of food and the date of loading.

• It is extremely important that food is frozen as quickly as possible. If the amount of food being frozen is too large, the quality of freezing is reduced, which affects the quality of the food.

To reverse the doors, you will need a Philips screwdriver, a flat-bladed screwdriver, and a hexagonal spanner. It is recommended that two people handle the unit during this process. All parts removed must be saved for reinstallation.

1. Ensure the unit is unplugged and empty. To take the door off, it is necessary to tilt the unit backward. Rest the unit on something solid so it will not slip.

2. Unscrew the top hinge cover, then unscrew the top hinge. Lift the upper door off and place it on a soft pad to avoid scratches.

3. Remove the hinge pin with a screwdriver and flip the hinge bracket over. Then refit the pin to the hinge bracket.

4. Remove the top left screw cover from the refrigerator cabinet.

5. Unscrew and remove the middle hinge.

6. On the top of the lower door, move the shaft sleeve and pin hole plug from the left side to the right side.

7. On the refrigerator cabinet, move the middle hinge hole covers from the left side to the right side.

8. Unscrew the bottom hinge and remove the adjustable feet from both sides.

9. On the refrigerator cabinet, move the bottom hinge hole covers from the left side to the right side.

10. Disassemble the original right-side bottom hinge. Find the new bottom hinge (for the left side) from the spare parts bag and install it.

11. Refit the bracket with the bottom hinge pin. Replace both adjustable feet. Transfer the lower door to its new position on the left-side hinge.

12. Reverse the middle hinge’s direction by 180 degrees and transfer it to the left side position. Insert the middle hinge pin into the upper hole of the lower door, then tighten the bolts.

13. Place the upper door back on. Ensure the door is aligned horizontally and vertically so the seals are closed on all sides before finally tightening the top hinge. Insert the top hinge and screw it to the top of the unit, then attach the hinge cover (from the accessory bag) with its screw.

14. Take the screw cover removed in step 4 and place it on the now-empty right side and fix it with a screw.

• First, turn off the refrigerator and unplug it from the wall outlet.

• Remove all food content.

• Wash the inside with a damp warm cloth soaked in a solution of lukewarm water and baking soda (about 2 tablespoons of baking soda to a quart of water).

• Ensure the door gasket (seal) is kept clean to maintain the unit’s efficiency.

• Clean the outside of the refrigerator with a mild detergent and warm water.

• Dry the interior and exterior with a soft cloth.

• For short vacations (less than three weeks): You can leave the refrigerator operating as usual.

• For long vacations (several months): Remove all food and unplug the power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it if necessary, or have the door removed.

• Turn off the refrigerator and unplug it from the wall outlet.

• Remove all food.

• Securely tape down all loose items inside the refrigerator, such as shelves.

• Tape the doors shut.

• Be sure the refrigerator remains in an upright position during transportation.

Yes, here are some tips to save energy:

• Locate the refrigerator in the coolest area of the room, away from heat-producing appliances or heating ducts, and out of direct sunlight.

• Let hot foods cool to room temperature before placing them in the refrigerator. Overloading the refrigerator forces the compressor to run longer.

• Be sure to wrap foods properly and wipe containers dry before placing them inside. This cuts down on frost build-up.

• Organize and label food to reduce door openings and extended searches. Remove as many items as needed at one time and close the door as soon as possible.

Check if the refrigerator is plugged in. Also, check if the circuit breaker has tripped or if a fuse has been blown.

This can be caused by several factors:

• The room temperature is hotter than normal.

• A large amount of food has been recently added.

• The door is being opened too often.

• The door is not closed completely.

• The temperature control is not set correctly.

• The door gasket is not sealing properly.

• The refrigerator does not have the correct clearances for ventilation.

• The unit was recently disconnected and needs up to 4 hours to cool down completely.

If the inside temperature is too warm, check the following:

• The temperature control may be set too warm. Turn it to a cooler setting and allow several hours for it to stabilize.

• The door is being kept open too long or opened too frequently. Try to open the door less often.

• The door is not closed completely or the gasket is not sealing properly.

• A large amount of warm or hot food may have been stored recently. Wait for the refrigerator to reach its selected temperature.

• The refrigerator may have been recently disconnected. It requires 4 hours to cool down completely.

The temperature control is likely set too cold. Turn the control to a warmer setting and allow several hours for the temperature to stabilize.

It is normal for the exterior refrigerator walls to feel warm, sometimes as much as 30°F warmer than the room temperature. This happens while the compressor works to transfer heat from inside the refrigerator cabinet to the outside.

Yes, this is normal. Metal parts undergo expansion and contraction, similar to hot water pipes. The sound should level off or disappear as the refrigerator continues to run.

This sound is normal. It is the refrigerant circulating throughout the cooling system.

Vibrations can be caused by the following:

• The refrigerator is not on a level surface. Check to ensure it is level.

• The floor is uneven or weak, causing the refrigerator to rock when moved slightly. Be sure the floor can adequately support the unit. You can level the refrigerator by putting wood or metal shims under part of it.

• The refrigerator is touching a wall. Re-level the refrigerator and move it away from the wall.

Moisture inside the refrigerator can be due to:

• Hot and humid weather, which increases the internal rate of frost build-up. This is normal.

• The door is slightly open or has been kept open too long or too frequently.

• The door is not sealed properly.

This typically happens when the door is slightly open, which allows the cold air from inside the refrigerator to meet warm, moist air from outside.

If the door is not closing properly, check if the refrigerator is on a level surface. Also, check if the gasket is dirty, as this can prevent a proper seal.