Free English LEDJ REPID QB1 LEDJ350A (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD LEDJ REPID QB1 LEDJ350A (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the technical specifications of the LEDJ REPID QB1 LEDJ350A?
The specifications for the LEDJ REPID QB1 LEDJ350A are as follows:
Power consumption: 45W
Power supply: 100~240V, 50/60Hz
Fuse: F3.15A 250V
Battery: 14.8V 5200mAh
Battery fuse: F5A 250V
Dimensions: 204 x 138 x 144mm
Weight: 3kg
What are the LEDJ REPID QB1 LEDJ350A battery life characteristics?
The LEDJ REPID QB1 LEDJ350A has a maximum run time of up to 18 hours in single colour mode, up to 8 hours for colour change or fade, and 4 hours when running full on. Please note that battery life is subject to usage and the temperature where the fixture is situated.
How do I charge the battery of the LEDJ REPID QB1 LEDJ350A?
The charging time for the LEDJ REPID QB1 LEDJ350A is 5 hours when the unit is powered off, and 9 hours when the unit is powered on. Battery fuse must be fitted before use.
What do the battery charge indicator colours mean on the LEDJ REPID QB1 LEDJ350A?
The indicator status is as follows: When illuminated red, the fixture is recharging. When illuminated yellow, the fixture has less than 30% charge. When illuminated green, the battery is charged.
How do I set the DMX address on the LEDJ REPID QB1 LEDJ350A?
To access the DMX address mode on the LEDJ REPID QB1 LEDJ350A, press the MENU button and use the UP and DOWN buttons to show d001 on the LED display. Press the ENTER button and use the UP and DOWN buttons to set the required DMX address. Press the ENTER button to confirm the setting.
How do I set the DMX channel mode on the LEDJ REPID QB1 LEDJ350A?
To access the DMX channel mode on the LEDJ REPID QB1 LEDJ350A, press the MENU button and use the UP and DOWN buttons to show CHAn on the LED display. Press the ENTER button and use the UP and DOWN buttons to choose one of the 4, 6, or 11 DMX channel modes. Press the ENTER button to confirm the setting.
How do I use the Wireless DMX operation on the LEDJ REPID QB1 LEDJ350A?
To operate the LEDJ REPID QB1 LEDJ350A in wireless DMX, connect the fixture to a W-DMX compatible wireless DMX transmitter. First, clear the fixture’s wireless DMX memory. To pair, ensure the wireless DMX indicator is off and the fixture is set to slave. Press the pair button on the transmitter. The wireless DMX indicator will start flashing fast. Once the pair is successful, the indicator will turn solid yellow.
How do I clear the wireless DMX memory on the LEDJ REPID QB1 LEDJ350A?
To clear the wireless DMX memory on the LEDJ REPID QB1 LEDJ350A, press the MENU button and use the UP and DOWN buttons to show N-5 on the LED display. Press the ENTER button and use the UP and DOWN buttons to choose SLAV. Press the ENTER button and the unit will show CLEA. Press and hold the DOWN button for 5 seconds to erase the memory.
What is the procedure for using the Colour mix mode on the LEDJ REPID QB1 LEDJ350A?
To access the colour mix mode on the LEDJ REPID QB1 LEDJ350A, press the MENU button to show NAnU on the display. Press ENTER and use the UP and DOWN buttons to choose rEd. Press ENTER and use UP and DOWN to select the brightness between 000 and 255. Press ENTER and repeat for GrEE (Green), bLUE (Blue), and ANbE (Amber).
How do I enable and configure the Eco mode on the LEDJ REPID QB1 LEDJ350A?
To set the LEDJ REPID QB1 LEDJ350A into eco mode, press the MENU button to show batt on the LED display. Press ENTER and use the UP and DOWN buttons to select ECon. Press ENTER and use the UP and DOWN buttons to choose between on or ofF. Press ENTER to confirm. Eco mode allows the fixture to run longer from a single charge when used in a 3 or more colour program with a slight reduction in intensity.
How do I use the master/slave mode on the LEDJ REPID QB1 LEDJ350A?
To set the master unit, press the MENU button to show N-5 on the display, press ENTER, choose NASt, and press ENTER. Then select your desired program. To set other units in slave mode, press the MENU button to show N-5, press ENTER, and use the UP and DOWN buttons to choose SLAV. Press ENTER to confirm. Ensure all slave units are set to the same DMX channel mode as the master unit.
What are the 11 channel mode DMX values for the LEDJ REPID QB1 LEDJ350A?
The 11 channel mode values are:
Channel 1: 000-255 Red dimmer (0-100%)
Channel 2: 000-255 Green dimmer (0-100%)
Channel 3: 000-255 Blue dimmer (0-100%)
Channel 4: 000-255 Amber dimmer (0-100%)
Channel 5: 000-255 Master dimmer (0-100%)
Channel 6: 000-010 No function, 011-255 Strobe (slow-fast)
Channel 7: 000-010 No function, 011-200 Colour macros, 200-255 White macros
Channel 8: 000-005 No function, 006-255 White colour temperature macros
Channel 9: 000-010 No function, 011-040 3 colour fade (RGB), 041-070 3 colour fade (CMY), 071-100 4 colour fade (RGBA), 101-130 7 colour fade (RGBACMY), 131-160 3 colour change (RGB), 161-190 3 colour change (CMY), 191-220 4 colour change (RGBA), 221-255 7 colour change (RGBACMY)
Channel 10: 000-255 Program speed (slow-fast)
Channel 11: 000-255 Sound active
CLICK HERE TO DOWNLOAD LEDJ REPID QB1 LEDJ350A (01) PDF DOCUMENT