LEDJ RAPID QB1 LEDJ353A (01) PDF MANUAL

To access the DMX address mode, press the “MENU” button to show “Address” on the OLED display. Now use the “UP” and “DOWN” buttons to set the required DMX address. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To access the DMX channel mode, press the “MENU” button to show “Channel” on the OLED display. Now use the “UP” and “DOWN” buttons to choose one of the 4/6 or 10 DMX channel modes. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

4 channel mode:

Channel	Value	Function
1	000-255	Red dimmer (0-100%)
2	000-255	Green dimmer (0-100%)
3	000-255	Blue dimmer (0-100%)
4	000-255	Amber dimmer (0-100%)

6 channel mode:

Channel	Value	Function
1	000-255	Red dimmer (0-100%)
2	000-255	Green dimmer (0-100%)
3	000-255	Blue dimmer (0-100%)
4	000-255	Amber dimmer (0-100%)
5	000-255	Master dimmer (0-100%)
6	000-010	No function
	011-255	Strobe (slow-fast)

10 channel mode:

Channel	Value	Function
1	000-255	Red dimmer (0-100%)
2	000-255	Green dimmer (0-100%)
3	000-255	Blue dimmer (0-100%)
4	000-255	Amber dimmer (0-100%)
5	000-255	Master dimmer (0-100%)
6	000-010	No function
	011-255	Strobe (slow-fast)
7	000-010	No function
	011-200	Colour macros
	201-255	White macros
8	000-005	No function
	006-255	White colour temperature macros
9	000-010	No function
	011-040	3 colour fade (RGB)
	041-070	3 colour fade (CMY)
	071-100	4 colour fade (RGBA)
	101-130	7 colour fade (RGBACMY)
	131-160	3 colour change (RGB)
	161-190	3 colour change (CMY)
	191-220	4 colour change (RGBA)
	221-255	7 colour change (RGBACMY)
10	000-255	Program speed (slow-fast)

To operate the fixture in wireless DMX you will need to connect the fixture to a W-DMX compatible wireless DMX Transmitter. Firstly clear the fixtures wireless DMX memory. To pair the fixture and transmitter make sure the wireless DMX indicator is off. To turn wireless DMX on, press the “MENU” button to show “Wireless DMX” on the OLED display. Now use the “UP” and “DOWN” buttons to select “On”. To put the unit into Wireless DMX receive mode, press the “ENTER” button again and use the “UP” and “DOWN” buttons to select “Receive”. Press the “ENTER” button to confirm the setting. Press the pair button on the WDMX G3/G4/G4S compatible transmitter. The wireless DMX indicator will start flashing fast. Once the pair is successful the indicator will turn solid yellow. To turn wireless DMX off, press the “MENU” button to show “Wireless DMX” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Off”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To clear the wireless DMX memory, press the “MENU” button to show “Wireless DMX” on the OLED display. Now use the “UP” and “DOWN” buttons to select “ClearAll” (Transmit mode) or “Clear” (Receive mode). Press the “ENTER” button to erase the wireless DMX memory. The Wireless DMX indicator will go off. To exit out of any of the above options, press the “MENU” button. Please note: When the fixture is in Wireless DMX transmit mode the wireless DMX memory of the Transmitter unit and all receiving units will be cleared (ClearAll). When in Wireless DMX receive mode the wireless DMX memory of that one receiving unit will be cleared (Clear).

When the Wireless DMX indicator LED is illuminated, the fixture is paired. When the Wireless DMX indicator LED is flashing fast, the fixtures settings from the last pair are saved but the fixture isn’t paired with the transmitter. When the Wireless DMX indicator LED is flashing slow, the fixtures is paired with the transmitter but isn’t receiving signal. When the Wireless DMX indicator LED is off, the fixtures doesn’t have any remembered wireless DMX settings and isn’t paired with a transmitter.

To access the DMX signal fail setting, press the “MENU” button to show “DMX Fail” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “Hold”, “Blackout” or “Auto”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To access the LED refresh rate setting, press the “MENU” button to show “Frequency” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “600Hz”, “1200Hz”, “2000Hz”, “4000Hz” or “25kHz”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To access the colour mix mode, press the “MENU” button to show “Colour Mix” on the OLED display. Now use the “UP” and “DOWN” buttons to choose “Red”. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select the brightness of Red between “000-255”. Value: 000 – 255 (000 = low, 255 = high). Now press the “ENTER” button and repeat for “Green”, “Blue” and “Amber”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To access the built-in programs, press the “MENU” button to show “Program” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “Static”, “Fade” or “Auto”.

Static:

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Colour: 1 – Colour: 25”. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Strobe: 0 – Strobe: 10”.Press the “ENTER” button to confirm the setting.

• Colour 1 – Red
• Colour 2 – Green
• Colour 3 – Blue
• Colour 4 – Amber
• Colour 5 – Cyan
• Colour 6 – Magenta
• Colour 7 – Yellow
• Colour 8 – White
• Colour 9 – Orange
• Colour 10 – Lime Green
• Colour 11 – Lavender
• Colour 12 – Yellow/Orange
• Colour 13 – Pink
• Colour 14 – Light Blue
• Colour 15 – Colour 25 – White colour temperature macros

Fade:

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Fade: 1 – Fade: 5”. Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Speed: 1 – Speed: 9”. Press the “ENTER” button to confirm the setting. (1 = slow speed, 9 = fast speed).

Auto:

Press the “ENTER” button and use the “UP” and “DOWN” buttons to select between “Speed: 1 – Speed: 9”. Press the “ENTER” button to confirm the setting. (1 = slow speed, 9 = fast speed).

To set the master unit, press the “MENU” button to show “Wireless DMX” on the OLED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select “Transmit”. Press the “ENTER” button to confirm the setting. Then select your desired program. To set the other units in slave mode, press the “MENU” button to show “Wireless DMX” on the OLED display. Now press the “ENTER” button and use the “UP” and “DOWN” buttons to select “Receive”. Press the “ENTER” button to confirm the setting. The unit will now run in sequence with the master unit. To exit out of any of the above options, press the “MENU” button. Please ensure that all slave units are set to the same DMX channel mode as the master unit.

Firstly clear the fixtures wireless DMX memory. To set the units into master/slave follow the instructions for Master/Slave operation. To pair the master unit with the slave(s), press the “MENU” button to show “Wireless DMX” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Pair”. Press the “ENTER” button to pair. The wireless DMX indicator will start flashing fast. Once the pair is successful the indicator will turn solid yellow.

To display the software version, press the “MENU” button to show “Information” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Version”. Press the “ENTER” button and the software version will be displayed. To exit out of any of the above options, press the “MENU” button.

To display the current fixture run time, press the “MENU” button to show “Information” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Current Time”. Press the “ENTER” button and the current fixture run time will be displayed. To exit out of any of the above options, press the “MENU” button.

To display the total fixture run time, press the “MENU” button to show “Information” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Total Time”. Press the “ENTER” button and the total fixture run time will be displayed. To exit out of any of the above options, press the “MENU” button.

To display the fixture temperature, press the “MENU” button to show “Information” on the OLED display. Now use the “UP” and “DOWN” buttons to select “Temperature”. Press the “ENTER” button and the software version will be displayed. To exit out of any of the above options, press the “MENU” button.

To access the eco mode setting, press the “MENU” button to show “Eco Mode” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “On” or “Off”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button. Please note: Eco mode allows the fixture to run longer from a single charge when used in a 3 or more colour program with a slight reduction in intensity.

To access the IR remote setting,, press the “MENU” button to show “IR” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “On” or “Off”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button. Please note: The fixture must be set to Master for the IR function to work.

The OLED display for this fixture has a menu locking function where after 5 seconds of inactivity it will lock. To unlock the menu hold the “MENU” and “DOWN” buttons for 3 seconds. To access the menu lock setting, press the “MENU” button to show “Menu Lock” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “On” or “Off”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

To access the factory reset setting, press the “MENU” button to show “Factory Reset” on the OLED display. Now use the “UP” and “DOWN” buttons to choose between “Yes” or “No”. Press the “ENTER” button to confirm the setting. To exit out of any of the above options, press the “MENU” button.

IR Remote Functions:

• 01 – Sets the unit into blackout off/on (LED on/off)
• 02 – Sets the static colour (see chart key for colours) A – Red, B – Green, C – Blue, D – Amber, E – Orange, F – Cyan, G – Pink
• 03 – Runs the auto mode, use the ‘Speed’ button followed by the ” and ” buttons to adjust the auto speed
• 04 – Runs the sound program, use the ‘ and buttons to adjust the sound sensitivity
• 05 – Runs the strobe program, use the ‘and buttons to adjust the strobe speed
• 06 – Sets the auto/fade speed. Press this button followed by the ” and buttons to adjust the program speed
• 07 – Sets the unit in either master or slave mode
• 08 – Runs the fade mode, use the ‘Speed’ button followed by the ” and buttons to adjust the fade speed
• 09 – Sets the DMX address. Press this button followed by the ” and buttons to adjust the DMX address. Press this button again followed by the ” and ” buttons to adjust the DMX channel
• 10 – Sets the unit in full on. Press this button followed by the ” and ” buttons to adjust brightness (000-255)
• 11 – Sets the unit in Eco mode. Press this button followed by the ‘A’ and ‘▼’ buttons to turn eco mode on/off
• 12 – Adjusts the auto, fade and strobe speed, sound sensitivity, DMX address/channel, full on brightness and turns the eco mode on/off.