Free English LASERLINER AC-TRACER (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD LASERLINER AC-TRACER (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the function of the LASERLINER AC-TRACER?
The LASERLINER AC-TRACER is a cable tracer set consisting of a transmitter and a receiver. Its primary functions include fast tracing of coherent electrical circuits, locating lines in coherent live electrical circuits, and detecting fuse circuits in live installations.
How is the LASERLINER AC-TRACER powered?
The transmitter (Sender TX) of the LASERLINER AC-TRACER is powered directly from the power cable being tested, which allows for measurements under operating conditions. The receiver (Receiver RECV) is powered by one 9V 6LR61 (9-volt block) battery.
How do I set up the transmitter (Sender TX) for the LASERLINER AC-TRACER?
The transmitter does not require a battery as it is powered by the mains supply. Before use, connect the desired lead (Euro connector, E27 lamp adapter, or UK plug), ensuring correct polarity. The device is operational when the ON indicator lamp is lit.
How do I insert the battery into the LASERLINER AC-TRACER receiver?
Open the battery compartment on the back of the receiver and insert one 9V 6LR61 battery, ensuring that the polarities are correct as indicated by the installation symbols.
How do I locate cables, sockets, or circuits using the LASERLINER AC-TRACER?
First, connect the transmitter to the line to be measured. Then, switch on the receiver and start tracing. The receiver provides a signal tone when the measured object belongs to the same electrical circuit. The receiver can detect cables up to a maximum depth of 5 cm.
Are there tips for better results when using the LASERLINER AC-TRACER?
Yes, consider the following tips for the LASERLINER AC-TRACER:
Tip 1: Set the receiver to maximum sensitivity and hold the sensor head as close as possible to the cable connection when tracing.
Tip 2: Decrease the receiver sensitivity in steps when locating a fuse to narrow down the area.
Tip 3: Rotate the receiver around its longitudinal axis by 90 degrees or change its horizontal and vertical position to adjust to different automatic circuit breakers with magnetic coils in various positions.
What are the technical specifications for the transmitter of the LASERLINER AC-TRACER?
The technical data for the Sender TX is as follows:
Nominal voltage: 200 to 240V
Maximum input voltage: 300V AC
Pollution degree: 2
Power supply: 200-240V AC, 50-60 Hz
Operating conditions: 0 degrees Celsius to 40 degrees Celsius, max. humidity 80 percent rH, no condensation, max. working altitude 2000 m above sea level
Storage conditions: -20 degrees Celsius to 60 degrees Celsius, max. humidity 80 percent rH
Weight: 54 g
Dimensions: 50 x 80 x 32 mm
What are the technical specifications for the receiver of the LASERLINER AC-TRACER?
The technical data for the Receiver RECV is as follows:
Measuring range: 0 to 5 cm measuring depth
Power supply: 1 x 9V 6LR61 (9-volt block)
Operating conditions: 0 degrees Celsius to 40 degrees Celsius, max. humidity 80 percent rH, no condensation, max. working altitude 2000 m above sea level
Storage conditions: -20 degrees Celsius to 60 degrees Celsius, max. humidity 80 percent rH
Weight: 155 g (incl. battery)
Dimensions: 68 x 165 x 36 mm
CLICK HERE TO DOWNLOAD LASERLINER AC-TRACER (01) PDF DOCUMENT