Free English LASERLINER THERMOSPOT POCKET (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD LASERLINER THERMOSPOT POCKET (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the primary function of the LASERLINER THERMOSPOT POCKET?
The LASERLINER THERMOSPOT POCKET is a non-contact infrared temperature measuring device featuring an integrated laser. By measuring and evaluating the amount of electromagnetic energy in the infrared wavelength range, it enables the non-contact measurement of surface temperatures.
What safety precautions must be followed regarding the laser on the LASERLINER THERMOSPOT POCKET?
The device uses a Class 2 laser. The following safety instructions must be observed:
• Attention: Do not look into the direct or reflected beam.
• Do not point the laser beam towards persons.
• If a person’s eyes are exposed to class 2 laser radiation, they should shut their eyes immediately and move their head away from the beam.
• Under no circumstances should optical instruments (such as a magnifying glass, microscope, or binoculars) be used to look at the laser beam or reflections.
• Do not use the laser at eye level (1.40 … 1.90 m).
• Manipulations or modifications to the laser device are prohibited.
How do I insert or change the battery in the LASERLINER THERMOSPOT POCKET?
To insert the battery, open the battery compartment and insert the battery according to the installation symbols. Ensure the correct polarity is observed during insertion.
How do I turn the LASERLINER THERMOSPOT POCKET on and off?
The device turns on when you press the button. It switches off automatically after 30 seconds of inactivity. To switch the device back on, press the button again.
How do I perform a continuous measurement with the LASERLINER THERMOSPOT POCKET?
To carry out a continuous measurement, activate the laser and keep the button pressed. Release the button as soon as the target laser pinpoints the desired measurement location. The measured value will be held on the display (Hold function).
What is the purpose of the laser circle on the LASERLINER THERMOSPOT POCKET?
The laser circle serves as a targeting aid to visualize the location of the infrared measurement. Temperature measurement takes place only on the surface. You should adjust the optimal measuring distance for the measurement spot (12:1) so that the spot lies completely within the measurement object.
How do I toggle between Minimum and Maximum values on the LASERLINER THERMOSPOT POCKET?
During a continuous measurement, the MIN or MAX value can be shown on the display. By pressing the MIN/MAX button, you can switch between these two values.
What material surfaces is the LASERLINER THERMOSPOT POCKET suitable for?
The device is permanently set to an emission coefficient of 0.95, which is applicable for most organic materials, as well as plastics, ceramics, wood, rubber, and stone. Ensure that the measurement area between the instrument and the surface is free of disturbances such as steam, gas, dirt, or glass.
How should I clean and maintain the LASERLINER THERMOSPOT POCKET?
Clean all components with a slightly damp cloth and avoid using cleaning agents, scouring agents, or solvents. Remove the battery (or batteries) before storing the device for a longer period. Store the device in a clean and dry place.
How often should the LASERLINER THERMOSPOT POCKET be calibrated?
The measuring instrument should be calibrated and tested regularly to ensure the accuracy of the measurement results. A calibration interval of one year is recommended.
What are the technical specifications of the LASERLINER THERMOSPOT POCKET?
| Measured variable | Infrared temperature |
| Functions | Min / Max / Hold |
| Infrared temperature measuring range | -40°C … 400°C |
| Infrared temperature accuracy | ± 2°C + 0.1°C / degree (-40°C … 0°C) ± 2°C or ± 2% (0°C … 400°C), whichever is greater |
| Laser wavelength | 650 nm |
| Laser class | 2 / < 1 mW (EN 60825-1:2014/AC:2017) |
| Emission coefficient | Fixed, 0.95 |
| Optics | 12:1 (12 m measuring distance : 1 m measuring spot) |
| Auto power off | After 30 seconds |
| Operating conditions | 0°C … 40°C, max. humidity 80% rH, non-condensing, working altitude max. 2000 m above sea level |
| Storage conditions | -10°C … 60°C, max. humidity 80% rH, non-condensing |
| Power supply | 1 x 9V 6LR61 (9-V block) |
| Operating time | Approx. 35 hours |
| Dimensions (W x H x D) | 95 x 132 x 37 mm |
| Weight | 144 g (including battery) |
What are the specific display indicators on the LASERLINER THERMOSPOT POCKET screen?
The display indicators are defined as follows:
a: Hold Function
b: Battery status
c: Measured value display
d: MIN or MAX value during measurement
e: Laser beam on
f: Unit of measure °C
g: Switching between MIN/MAX
h: Laser exit
i: ON / Measure
CLICK HERE TO DOWNLOAD LASERLINER THERMOSPOT POCKET (01) PDF DOCUMENT