KOBE CH3830SQBD-1 (01) PDF Document

Free English KOBE CH3830SQBD-1 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD KOBE CH3830SQBD-1 (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What should I do in the event of a range top grease fire with the KOBE CH3830SQBD-1?

To handle a range top grease fire when using the KOBE CH3830SQBD-1, you should:

1. Smother flames with a tight fitting lid, cookie sheet, or metal tray, and then turn off the burner. Keep flammable or combustible material away from flames. If the flames do not go out immediately, evacuate the area and call the fire department or 911.

2. Never pick up a burning pan as you may get burned.

3. Do not use water, including wet dishcloths or towels, as a steam blast will result.

4. Use an extinguisher only if you have a Class A, B, or C extinguisher and know how to operate it, the fire is small and contained in the area where it started, the fire department has been called, and you can fight the fire with your back to an exit.

What are the steps if I smell gas while operating the KOBE CH3830SQBD-1?

If you smell gas, take the following actions immediately:

1. Extinguish any open flame.

2. Do not try to turn on the lights or any type of appliance, including the KOBE CH3830SQBD-1.

3. Open all doors and windows to disperse the gas. If you still smell gas, call the Gas Company and Fire Department right away.

How do I operate the fan on the KOBE CH3830SQBD-1?

To operate the fan function on your KOBE CH3830SQBD-1, follow these steps:

1. Press the Power Control button to turn on the range hood.

2. The fan will start on Speed #3. Press the button to decrease the speed level or press the button to increase the speed level.

3. To activate the 3-minute delay shutoff, press and hold the power button. Once activated, the LED Display will flash and the fan speed will change to Speed #3. You can adjust the speed level by pressing the increase or decrease buttons during the 3-minute countdown.

4. To turn the fan off immediately, press the power button a second time.

How do I operate the light function on the KOBE CH3830SQBD-1?

Press the light button to turn the LED lights on. Each press of the button will cycle the light intensity through Bright, Medium Bright, Dim, and OFF. Lights are controlled independently from the Power Control and delay shutoff features.

How does the ECO Mode feature work on the KOBE CH3830SQBD-1?

ECO Mode is designed to turn the fan on the QuietMode setting for 10 minutes every hour to remove excess moisture, microscopic particles, and odors for better kitchen air quality. This mode is independent from the Power Control and delay shutoff.

To activate ECO Mode, press and hold the ECO button until the E icon appears in the LED Display. While the fan is running in this mode, you can still change the speed, use delay shutoff, or turn off the fan without disabling ECO Mode.

When the fan is off and ECO Mode is active, the E icon will appear in the display and will flash while ECO Mode is operating on QuietMode. To deactivate, press and hold the ECO control button until the E icon no longer appears.

Note: You must open a door or window to create sufficient make-up air when ECO Mode has been activated.

How do I maintain and clean the KOBE CH3830SQBD-1 surface?

To clean the surface of the KOBE CH3830SQBD-1:

1. Use only mild soap or detergent solutions and dry surfaces using a soft cloth.

2. If the stainless steel hood looks splotchy, use a stainless steel cleaner. Avoid getting cleaning solution onto or into the control panel. Do not leave the cleaner on too long, as it may cause damage to the hood finish. Use a soft towel to wipe off the cleaning solution and gently rub off any stubborn spots, then dry with a clean soft towel.

3. Do not allow deposits to accumulate or remain on the hood.

4. Do not use ordinary steel wool or steel brushes, as small bits of steel may adhere to the surface and cause rusting.

5. Do not allow salt solutions, disinfectants, bleaches, or cleaning compounds to remain in contact with stainless steel for extended periods, as they may be harmful.

Caution: Never use abrasive cleaners, pads, or cloths.

How do I clean the baffle filters on the KOBE CH3830SQBD-1?

To clean the baffle filters on your KOBE CH3830SQBD-1, remove all the baffle filters, spacers, and the oil tunnel if present. Wash them with warm soapy water using a sponge and dry them completely before returning them into place. Baffle filters are top rack dishwasher safe.

Caution: Always drain oil from baffle filters, spacers, and the oil tunnel regularly to prevent overflow. Be mindful of sharp edges during the cleaning process.

What are common troubleshooting solutions for the KOBE CH3830SQBD-1?

The following table lists common issues and their solutions for the KOBE CH3830SQBD-1:

Issue	Possible Cause	Solution
After installation, both motors and lights are not working.	The power is not on.	Make sure the circuit breaker and the unit’s power is ON. Use a voltage meter to check the power supply.
After installation, both motors and lights are not working.	The wire connection is not secure.	Check and tighten wire connection.
After installation, both motors and lights are not working.	The control panel and processor board wiring are disconnected.	Check wire continuity from control panel to processor board.
After installation, both motors and lights are not working.	The control panel and processor board is defective.	Replace the control panel or processor board.
Lights are working, but motor(s) is not.	The motor(s) is defective.	Replace the motor.
Lights are working, but motor(s) is not.	The capacitor(s) is defective.	Replace capacitor(s).
Lights are working, but motor(s) is not.	The control panel or processor board is defective.	Replace the control panel or processing board.
The range hood is vibrating.	The blower system is not secure.	Tighten the turbine impeller/squirrel cage and air chamber.
The range hood is vibrating.	The turbine impeller/squirrel cage is not balanced.	Replace the turbine impeller/squirrel cage.
The range hood is vibrating.	Hood is not secured in place.	Check the installation of hood, tighten the mounting bracket.
The motor is working, but the lights are not working.	LED light fixture(s) is defective.	Replace LED light fixture(s).
The motor is working, but the lights are not working.	The light wiring(s) is loose.	Check wire continuity from processor board to light transformer to LED light fixture(s).
The motor is working, but the lights are not working.	The control panel or processor board is defective.	Replace the control panel or processing board.
The range hood is not venting out correctly.	The range hood is installed outside of the manufacture recommended clearance.	Adjust the clearance between the range hoods and cook top to 26″ to 30″.
The range hood is not venting out correctly.	There is no make-up air inside the house.	Open the window to enhance the performance of the range hood by creating a sufficient make-up air.
The range hood is not venting out correctly.	Obstacle blocking the pipe work.	Remove all obstacles from the duct work.
The range hood is not venting out correctly.	The pipe size is smaller than the suggested pipe size.	Change the ducting according to the manufacture suggestion.
Cold air is coming into the home.	The pipe connection is not properly sealed.	Check the pipe installation.
Cold air is coming into the home.	The damper is not properly installed or is missing from the installation.	Check the damper installation.
Cold air is coming into the home.	The damper is not installed.	Installing the damper will help eliminate air backflow.