JOHN DEERE LPBS36JD (04) PDF Document

Always operate the JOHN DEERE LPBS36JD Broadcast Spreader with the speed limit for which it was designed – 3 mph. The recommended operating speed is slightly faster than that of a brisk walk, 3 mph. 3 mph is equal to the vehicle traveling 40 ft in nine seconds.

Park machine safely. See “Parking Safely” in Safety section. Then, remove the small closed-style spring locking pin (ii) and hitch pin (Z) from hitch clevis (L) of the spreader.

Step 1. Park machine safely. See “Parking Safely” in Safety section.

Step 2. Remove small closed-style spring locking pin (ii) and hitch pin (Z) from hitch clevis (L) of spreader.

Step 3. Pull spreader forward and position hitch clevis to straddle machine rear hitch plate or drawbar (not shown). Align all hitch pin holes, then install hitch pin down through hitch clevis and machine hitch, securing with small closed-style spring locking pin.

Step 1. Park machine safely. See “Parking Safely” in the Safety section.

Step 2. Remove all materials from the hopper before removing spreader from machine.

Step 3. Remove small closed-style spring locking pin from hitch pin.

Step 4. Hold spreader tow tube to remove pressure from hitch pin, then remove the hitch pin from hitch clevis and rear hitch plate or drawbar on machine.

Step 5. Pull or push spreader backward to disengage hitch clevis from machine hitch, install hitch pin in hitch clevis for storage and secure with small closed-style spring locking pin.

Step 1. Stop vehicle on a level surface, not on a slope.

Step 2. Lock park brake.

Step 3. Stop engine.

Step 4. Before you leave the operator’s seat, wait for engine and all moving parts to stop.

The JOHN DEERE LPBS36JD Broadcast Spreader can be tipped upright and stored against a wall using less space:

Step 1. Remove any loose material from hopper and fan using a brush and garden hose. The spreader should be clean and dry before storing.

Step 2. Roll spreader to desired storage area, lift hitch clevis to pivot spreader to vertical position.

Check for loose or missing hardware.

Make sure all connections are tight.

Make sure attachment responds properly to controls.

Check for debris build-up that could obstruct proper motion of the spreader control components.

Check to make sure tires on composite (plastic) rims are inflated to 30 psi (2.1 bar) (207 kPa), or tires on metal rims are inflated to 20 psi (1.3 bar) (138 kPa) maximum.

Always operate the JOHN DEERE LPBS36JD Broadcast Spreader with the speed limit for which it was designed – 3 mph.

When backing, carefully back straight to avoid jack knifing, which could result in damage to equipment.

Only tow the JOHN DEERE LPBS36JD Broadcast Spreader behind vehicles for which it was designed – riders, and lawn and garden tractors.

Do not load the hopper with more than the maximum weight capacity of 79 kg (175 lb).

Break up any lumps as you fill the hopper.

Do not use on windy days, especially when spreading fine grass seed or herbicides.

Optimum hitch height is 18 – 23 cm (7-9 in.).

The flow control handle should have resistance to movement. Increase or decrease spring tension as required to get desired flow control handle resistance.

The Fan Speed and Spread Width of the JOHN DEERE LPBS36JD Broadcast Spreader are controlled by the speed of the vehicle. The recommended operating speed is slightly faster than that of a brisk walk, 3 mph. 3 mph is equal to the vehicle traveling 40 ft in nine seconds.

The Flow Control Assembly on the JOHN DEERE LPBS36JD Broadcast Spreader operates the flow control plate. The flow control assembly is marked 0 (closest) to 10 (fully open). The position selected determines the amount of material to be broadcast. The higher the number, the heavier the application of material.

For many of the common fertilizers, insecticides, and grass seeds, flow control settings are provided in the alphabetized table listing flow control settings. If the product is not listed in the flow control settings table, use the calibration guide to set the flow control.

The Agitator Spring on the JOHN DEERE LPBS36JD Broadcast Spreader is located inside the hopper. It provides consistent material flow of pelletized materials and seed. It is not designed to break up lumps of material or seed. Break up any lumps as you fill the hopper.

After determining the correct setting number for your material, loosen knob and move stop bracket to that position. Tighten knob. Move flow control handle to the lock position to open the flow control plate.

Adjustment can be made by moving the direction control plate (#) to the right or left. The directional decal located below the directional control plate will aid you in adjusting the spread pattern. For most applications the plate should be placed close to the center position (2) described by the label above. If the material is coming out right or left during operation, adjustment of this plate should be made to center the material distribution pattern behind the vehicle. The JOHN DEERE LPBS36JD Broadcast Spreader has a patented feature to allow you to adjust for centering.

The directional control plate can be used for adjusting the material spread pattern when spreading near sidewalks (#), planting beds (4), etc. With the plate adjusted to the left side (1), the directional control plate only operates with 90% shut-off of material to the right side (3) of the vehicle as shown in the illustration.

The key to years of trouble-free service is to keep the JOHN DEERE LPBS36JD Broadcast Spreader clean and dry.

Never allow material to remain in hopper for extended periods of time.

Should rust develop, sand lightly and then paint area with enamel.

Periodically check all fasteners for tightness.

Rinse / dry inside and outside of spreader after each use. Move flow control as you rinse, to avoid build up of material.

Step 1. Remove snap ring (mm), 5/8 in. flat washer (N), wheel (C), two 5/8 in. flat washers (O) (if installed), spacer (M), 5/8 in. flat washer (O), and axle bearing (II). Remove open-style spring locking pin (gg).

Step 2. Remove large closed-style spring locking pin (hh), and slide axle (I) out from support frame (A). Remove axle bearing, two 5/8 in. flat washers (if installed), spacer, 5/8 in. flat washer, and axle bearing on opposite side of axle.

Step 3. Clean parts.

Step 1. Remove snap ring (mm), 5/8 in. flat washer (O), wheel (C), washers (O) (if installed), and axle bearing (II). Remove open-style spring locking pin (gg).

Step 2. Remove large closed-style spring locking pin (hh), and slide axle (I) out from support frame (A). Remove axle bearing (II) and washers (O) (if installed) on axle.

Step 3. Clean parts.

Step 1. Remove two 5/16 x 2-3/4 in. bolts (W), four 5/16 in. flat washers (nn), four pivot bushings (cc), and two 5/16 in. nylon locknuts (S). Remove assembled gage plate (E) from tow tube (F).

Rotate assembled gage plate (E) approximately 90° clockwise, and remove formed end of the link rod (G) from hole (#) on the hopper control plate, as shown.

Remove the transmission bracket (H) from tow tube (F) by removing the two 5/16 in. nylon locknuts (S) and two 5/16 in. flat washers (nn).

Step 4. Remove 1/8 x 1 in. cotter pin (ee), 3/8 in. ID O-ring (V), and agitator (ff) from transmission shaft (H).

Step 5. Remove transmission (H) assembly.

Step 6. Clean fan (J).

Step 7. Remove the four bolts (1), washers (2), nuts (3) and straps (4) that hold the gate (5) and directional control plate (6).

Step 8. Separate parts as shown.

Step 9. Clean thoroughly using soap and water. NOTE: Be sure to calibrate the gage plate before using spreader (see “Calibrate Gage Plate” in the Assembly section).

Step 10. Assemble parts reverse order of removal.

Calibrate the gage plate.

Check if flow control handle hardware is too tight: Loosen 5/16 x 2-3/4 in. bolt on flow control handle assembly. Take gate and directional control plates apart; clean plates out with soap and water.

Turn off engine, set parking brake, fully open gate, shake hopper until material flows, close gate.

Find or replace missing open-style spring locking pin on right wheel rim.

Find or replace missing large closed-style spring locking pin in transmission.

Check position of fan and fan driver.

Check for transmission malfunction: With the broadcast spreader attached to your machine, lift the drive wheel and rotate. At the same time apply gentle pressure to the fan shaft. It should turn with each rotation of the wheel.

DIMENSIONS

Size (maximum weight) . . . . . . . . . 79 kg (175 lb)

Capacity . . . . . . . . . . . . . . . 0.10 cu m (3.5 cu ft)

Empty Mass . . . . . . . . . . . . . . 18.1 kg (40 lbs)

Maximum Tongue Weight . . . . . . . . 17.2 kg (38 lbs)

WHEELS AND TIRES

Tire Size . . . . . . . . . . . . . . . 33.0 x 10.2 cm (13 x 5 in) Turf tread

TIRE INFLATION

Composite (Plastic) Rim Tire Inflation . . . . . . . . 207 kPa (2.1 bar) (30 PSI)

(Metal) Rim Tire Inflation . . . . . . . . 138 kPa (1.3 bar) (20 PSI)

If the product you are using is not listed in the flow control setting table (pages 25-27), use this calibration guide to set the flow control. NOTE: Calibration guide information is also provided on the hopper decal of the spreader.

Step 1. Using application information on product package, find the calibration setting in the following guide and set calibration control lever.

Step 2. Adjust spread pattern.

Step 3. Calibration settings have been determined using a 3 MPH pace or 40 ft. of travel in 9 seconds.

Calibration Guide for Flow Control Settings table: