Free English JOHN DEERE JD310 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD JOHN DEERE JD310 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the recommended specifications for a preliminary engine test on the JOHN DEERE JD310?
The preliminary engine testing specifications for the JOHN DEERE JD310 are:
| Operation | Specification | Section-Group Reference |
|---|---|---|
| Dynamometer Test (at 2500 engine rpm) | Compare with previous recorded output; compare with output after tune-up | FOS 30 |
| Compression Test (Diesel) | 300 psi (min)* | FOS 30 ENGINES |
| Compression Test (Gasoline) | 120 psi (min)* | 20-30 |
| Manifold Depression Test (gasoline) (fast idle) | 15 to 20 inches of mercury | FOS 30 ENGINES, 20-30 |
| Engine Coolant Check Test | No air bubbles or oil film in radiator | FOS 30 ENGINES |
* The difference between cylinders should be no more than 30 psi on gasoline engines and 50 psi on diesel engines.
What are the recommended specifications for the engine tune-up procedures on the JOHN DEERE JD310?
The engine tune-up specifications for the JOHN DEERE JD310 are:
| System | Service | Specification | Section-Group Reference |
|---|---|---|---|
| Air Intake System | Check restriction indicator operation (Diesel) | 22 to 27 inches at 2500 rpm (full load) | FOS 30 ENGINES |
| Air Intake System | Check restriction indicator operation (Gasoline) | 18 to 21 inches at 2500 rpm (full load) | FOS 30 ENGINES, 30-15 |
| Exhaust System | Check muffler and exhaust pipe for restrictions. | FOS 30 ENGINES | |
| Crankcase Ventilating System | Check system for restrictions. | FOS 30 ENGINES | |
| Cooling System | Clean grille screen, radiator core, and oil cooler core. | 20-25 | |
| Cooling System | Clean and flush system; check thermostat. | Starts to Open: 177°F.-184°F. (Gasoline), 201°F.-207°F. (Diesel) | 20-25 |
| Cooling System | Clean and flush system; check thermostat. | Fully Open: 202°F. (Gasoline), 213°F. (Diesel) | |
| Cooling System | Check pressure cap. | 6.25 to 7.50 psi | 20-30 |
Also, for the Air Intake System, service air cleaner and check system for leaks (Reference: FOS 30 ENGINES).
What is the procedure for Predelivery Service for the JOHN DEERE JD310?
For Temporary Tractor Storage during Predelivery Service for the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check radiator for coolant loss and antifreeze protection. | Midway between core and filler neck. | Operator’s manual. |
| Drain fuel system (gasoline). | Operator’s manual. | |
| Remove and store battery. | Store at room temperature. | |
| Reduce shipping pressure of tires. | ||
| Cover tractor and tires for protection and cleanliness. |
For PREDELIVERY INSPECTION:
| Service | Specifications | Reference |
|---|---|---|
| Cooling System: Inspect radiator for coolant loss. Check antifreeze protection. | Midway between core and filler neck. | Operator’s manual. |
| Electrical System: Check battery terminals to be sure they are tight. | Operator’s manual. | |
| Electrical System: Punch date code on battery tag. | ||
| Electrical System: Wet charged batteries: Inspect electrolyte and charge batteries if required. Check alternator belt tension. | To bottom of filler neck in each cell. 3/4-inch deflection with 20 lb. force. | FOS 20-ELECTRICAL SYSTEMS Operator’s manual. |
| Tires and Wheels: Adjust pressure of tires. Check front and rear wheel retainers for tightness. | Operator’s manual. Operator’s manual. |
For Lubrication during PREDELIVERY INSPECTION:
| Service | Specifications | Reference |
|---|---|---|
| Check crankcase oil level. | To upper marks on dipstick. | Operator’s manual. |
| Check transmission-hydraulic system oil level. | Operator’s manual. | |
| Lubricate grease fittings. | Operator’s manual. | |
| Check distributor lubrication. | Operator’s manual. |
For Engine during PREDELIVERY INSPECTION:
| Service | Specifications | Reference |
|---|---|---|
| Check air cleaner. | Operator’s manual. | |
| Fill fuel tank and start engine. | Capacity 19-1/2 U.S. Gallons. | Operator’s manual. |
| Check operation of lights, gauges, and indicator lights. | Operator’s manual. | |
| Check speed control and governor linkage for free operation. | Section 20, Group 20. | |
| Check engine idle speeds. | Section 20, Group 20. | |
| Drain sediment from fuel filter. | Operator’s manual. |
For Operation during PREDELIVERY INSPECTION:
| Service | Specifications | Reference |
|---|---|---|
| Clutch pedal wear adjustment. | Section 50, Group 10. | |
| Shift transmission through all gears. | Operator’s manual. | |
| Check differential lock operation. | Operator’s manual. | |
| Check hydraulic system operation. | Section 70, Group 5. | |
| Check brake operation. | Section 60, Group 5. | |
| Check steering operation. | Section 60, Group 10. | |
| Check seat operation. | Operator’s manual. |
For General items during PREDELIVERY INSPECTION:
| Service | Specifications | Reference |
|---|---|---|
| Tighten accessible nuts and cap screws. | ||
| Clean machine and touch up paint. |
What are the items to cover during the Delivery Service for the JOHN DEERE JD310?
Before completing the delivery acknowledgments portion of the Delivery Receipt for the JOHN DEERE JD310, the serviceman and owner should thoroughly review the following points using the operator’s manual as a guide:
- Controls and instruments.
- How to start and stop the engine.
- The importance of the break-in period.
- How to use cast-iron ballast.
- All functions of the hydraulic system.
- The importance of safety.
- The importance of lubrication and periodic services.
After explaining and demonstrating these features, the owner should sign the Delivery Receipt and be given the operator’s manual.
What checks are performed during the After-Sales Inspection for the Cooling System on the JOHN DEERE JD310?
For the Cooling System during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check radiator coolant level. | Midway between core and filler neck. | |
| Clean external surface of radiator core. | ||
| Check hoses and connections for leaks. |
What checks are performed during the After-Sales Inspection for the Fuel System on the JOHN DEERE JD310?
For the Fuel System during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Remove water and foreign matter from fuel pump and filter sediment bowls. | Operator’s manual. | |
| Check fuel line connections. | Operator’s manual. |
What checks are performed during the After-Sales Inspection for the Electrical System on the JOHN DEERE JD310?
For the Electrical System during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check specific gravity of battery. | Full charge at 80°F. is 1.260. | Operator’s manual. |
| Check level of battery electrolyte. | To bottom of filler neck in each cell. | Operator’s manual. |
| Check alternator belt tension. | 3/4-inch deflection with a 20-pound force. | Operator’s manual. |
| Start engine and check action of starter, lights, indicator lamps, and gauges. | Operator’s manual. |
What checks are performed during the After-Sales Inspection for Lubrication on the JOHN DEERE JD310?
For Lubrication during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check crankcase oil level. | To upper marks on dipstick. | Operator’s manual. |
| Check air cleaner dust cup, unloading valve, and element. | Operator’s manual. | |
| Check transmission-hydraulic system oil level. | Operator’s manual. | |
| Check distributor lubrication. | Operator’s manual. |
What checks are performed during the After-Sales Inspection for the Engine on the JOHN DEERE JD310?
For the Engine during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check valve tappet adjustment. | Section 10, Group 15. | |
| Check engine speed under load. | Section 50, Group 10. | |
| Check horsepower. |
What checks are performed during the After-Sales Inspection under the General category for the JOHN DEERE JD310?
For General items during the After-Sales Inspection of the JOHN DEERE JD310:
| Service | Specifications | Reference |
|---|---|---|
| Check clutch wear adjustment. | Section 50, Group 10. | |
| Check differential lock operation. | Operator’s manual. | |
| Check hydraulic system operation. | Section 70, Group 5. | |
| Check steering. | Section 60, Group 10. | |
| Check brakes. | Section 60, Group 5. | |
| Tighten accessible nuts and cap screws. | ||
| Tighten accessible hydraulic oil lines. | ||
| Visual inspection. |
What are the General Machine Specifications for the Engine on the JOHN DEERE JD310?
The General Machine Specifications for the Engine on the JOHN DEERE JD310 are as follows:
| Gasoline | Diesel | |
|---|---|---|
| Flywheel Horsepower (net) (observed at 2500 rpm) | 50 | 50 |
| Number of Cylinders | 3 | 3 |
| Bore and Stroke | 4.02 x 4.33 | 4.02 x 4.33 |
| Displacement | 164 | 164 |
| Compression Ratio | 7.5 to 1* | 16.2 to 1 |
| Firing Order | 1-2-3 | 1-2-3 |
| Engine Speeds: Slow Idle | 600 rpm | 800 rpm |
| Engine Speeds: Fast Idle | 2650 rpm | 2650 rpm |
| Engine Speeds: Governed Speed Range (rpm) | 600-2650 rpm | 800-2650 rpm |
| Valve Clearance: Intake | 0.014 in. | 0.014 in. |
| Valve Clearance: Exhaust | 0.022 in. | 0.018 in. |
* 8.6:1 High-Altitude Pistons
What are the General Machine Specifications for Capacities, Clutch, Transmission, and Differentials and Final Drives on the JOHN DEERE JD310?
The General Machine Specifications for the JOHN DEERE JD310 are:
| Component | Specification |
|---|---|
| Fuel Tank Capacity | 19-1/2 gals. |
| Cooling System Capacity | 12 qts. |
| Engine Crankcase Capacity (with filter) (early units) | 7 qts. |
| Engine Crankcase Capacity (with filter) (later units) | 9 qts. |
| Transmission-Hydraulic Reservoir Capacity | 20-1/2 gals. |
| Clutch | Single-stage, spring-loaded, dry-disk, foot-operated. |
| Transmission | Collar-shift with hydraulic reverser containing hydraulic wet clutches provide 8 speeds forward and 4 rearward. |
| Differentials and Final Drives | Planetary-reduction final drives with spiral bevel gear drive differential. |
| Differential lock | Foot-operated mechanical lock, spring-loaded out of engagement. |
What are the Electrical System Specifications for the JOHN DEERE JD310?
The Electrical System Specifications for the JOHN DEERE JD310 are:
| Specification | Value |
|---|---|
| Voltage | 12 |
| Battery Ground | Negative |
| Battery Specific Gravity | 1.260 |
What are the Front Tire Options for the JOHN DEERE JD310?
The Front Tire Options for the JOHN DEERE JD310 are:
| Size | Type | Ply Rating |
|---|---|---|
| 7.50-16 (Early Units) | I-1A | 6 |
| 7.50-16 (Early Units) | I-1A | 10 |
| 11L-15 | I-1 | 6 |
| 7.50-16 | I-1A | 8 |
| 11L-15 (Early Units) | I-1A | 8 |
What are the Rear Tire Options for the JOHN DEERE JD310?
The Rear Tire Options for the JOHN DEERE JD310 are:
| Size | Type | Ply Rating |
|---|---|---|
| 16.9-24 (Early Units) | R-1 | 8 |
| 16.9-24 | R-4 | 8 |
| 16.9-24 (Early Units) | R-3 | 8 |
| 18.4-24* | R-4 | 8 |
| 19.5-24 (Early Units) | R-4 | 8 |
* Use with 9500 Backhoe
What are the Operating Weights for the JOHN DEERE JD310 with the 9405 Backhoe?
The Operating Weights for the JOHN DEERE JD310 with the 9405 Backhoe are:
| Configuration | Gasoline | Diesel |
|---|---|---|
| Without canopy or cab | 12,700 lbs. | 12,750 lbs. |
| With canopy | 13,103 lbs. | 13,241 lbs. |
What are the Operating Weights for the JOHN DEERE JD310 with the 9500 Backhoe?
The Operating Weights for the JOHN DEERE JD310 with the 9500 Backhoe are:
| Configuration | Gasoline | Diesel |
|---|---|---|
| Without canopy or cab | 13,549 lbs. | 13,649 lbs. |
| With canopy | 14,291 lbs. | 14,391 lbs. |
What are the Operating Specifications for the Backhoe on the JOHN DEERE JD310?
The Operating Specifications for the Backhoe on the JOHN DEERE JD310 are:
| Measurement | (9405) | (9500) |
|---|---|---|
| Digging Depth (IEMC) | 14 ft. 1 in. | 13 ft. 9 in. |
| Backhoe Reach | 17 ft. 1 in. | 17 ft. 2 in. |
| Truck Loading Height | 10 ft. 4 in. | 10 ft. 9 in. |
Additional Backhoe Operating Specifications for the JOHN DEERE JD310:
| Measurement | Value |
|---|---|
| Over-all Height (top of canopy) | 8 ft. 8 in. |
| Turning Radius (with brakes) | 9 ft. 2 in. |
| Turning Clearance Circle (Loader hinge pin 3 ft. above ground level, bucket rolled back; brakes applied) | 30 ft. |
| Breakout Force | 6,000 lbs. |
| Stabilizer Width (transport position) (9405) | 7 ft. 3 in. |
| Stabilizer Width (transport position) (9500) | 6 ft. |
| Transport Width (9500) | 8 ft. 1 in. |
What are the Operating Specifications related to Dimensions for the JOHN DEERE JD310 Backhoe Loader?
The dimension-related Operating Specifications for the JOHN DEERE JD310 Backhoe Loader are:
| Measurement | (9405) | (9500) |
|---|---|---|
| Ground Clearance | 13 in. | 7 in. |
| Over-all Length (Transport position) | 23 ft. 9 in. | 18 ft. 6-1/2 in. |
Other Dimension Specifications for the JOHN DEERE JD310:
| Measurement | Value |
|---|---|
| Transport Height | 11 ft. 3 in. |
| Width (without bucket) | 6 ft. 11 in. |
What hydraulic and steering systems are specified for the JOHN DEERE JD310?
The Hydraulic System for the JOHN DEERE JD310 is specified as:
Closed-center, constant-pressure, variable displacement pump driven from front of engine. Provides hydraulic power for steering and loader-backhoe operation.
The Steering System for the JOHN DEERE JD310 is specified as:
Hydraulic power steering with provision for emergency manual steering.
How is the Brake System specified for the JOHN DEERE JD310?
The Brake System for the JOHN DEERE JD310 is specified as: Fully hydraulic, foot-operated, individually or simultaneously actuated, wet disk type.
CLICK HERE TO DOWNLOAD JOHN DEERE JD310 (01) PDF DOCUMENT