JOHN DEERE LPBS36JD (03) PDF Document

When towing loads with the JOHN DEERE LPBS36JD, keep the following safety points in mind:

Stopping distance increases with the speed and weight of the towed load, so travel slowly and allow extra time to stop.

The total towed weight must not exceed the limits specified in your towing vehicle operator manual.

Excessive load can cause loss of traction and control on slopes; reduce the weight when operating on slopes.

Never allow children or others in or on the towed equipment.

Use only approved hitches and attach equipment only at the approved hitch point.

Follow manufacturer recommendations for weight limits and use wheel weights or counterweights as required.

Avoid sharp turns and use caution when operating on adverse surfaces or when reversing.

Do not shift into neutral and coast downhill.

To operate the JOHN DEERE LPBS36JD safely, observe these guidelines:

The unit is intended for lawn care and home applications. Do not tow on highways or in high speed applications. Stay within the maximum recommended towing speed.

Towing speed should be slow enough to maintain control, especially over rough ground.

Do not allow children or untrained persons to operate the machine.

Keep riders off the JOHN DEERE LPBS36JD. Riders are subject to injury from foreign objects, being thrown off, or obstructing the operator view.

Check machine brake action before operation and service them as necessary.

Keep all nuts and bolts tight and ensure all parts are in good condition.

Do not modify the machine or safety devices, as this may impair function and safety.

Securely anchor all loads and distribute the load evenly for safe travel.

Do not obstruct the operator view during use.

Before disconnecting the JOHN DEERE LPBS36JD from the machine hitch plate, perform the following steps:

Unload the attachment.

Stop the attachment on level ground.

Stop the machine engine.

Lock the machine park brake.

Block the attachment wheels.

Ensure that your hands, feet, or other body parts are not under the towtube.

When operating the JOHN DEERE LPBS36JD, you should always wear substantial footwear and long trousers. Do not operate the equipment barefoot or while wearing open sandals. Always wear eye protection and consider using protective devices like earplugs if necessary. Use close fitting clothing and safety equipment appropriate for the job.

To install the JOHN DEERE LPBS36JD, first park the machine safely. Remove the small closed-style spring locking pin and the hitch pin from the hitch clevis of the spreader. Pull the spreader forward and position the hitch clevis to straddle the machine rear hitch plate or drawbar. Align all hitch pin holes, then install the hitch pin down through the hitch clevis and machine hitch, securing it with the small closed-style spring locking pin.

To remove the JOHN DEERE LPBS36JD, ensure the machine is parked safely and remove all materials from the hopper. Remove the small closed-style spring locking pin from the hitch pin. Hold the spreader tow tube to remove pressure from the hitch pin, then remove the hitch pin from the hitch clevis and the rear hitch plate or drawbar. Pull or push the spreader backward to disengage the hitch clevis from the machine, and install the hitch pin into the hitch clevis for storage, securing it with the small closed-style spring locking pin.

To store the JOHN DEERE LPBS36JD, first remove any loose material from the hopper and fan using a brush and garden hose; ensure the spreader is clean and dry. Roll the spreader to the desired storage area, and lift the hitch clevis to pivot the spreader to a vertical position so it can be stored against a wall.

Before using the JOHN DEERE LPBS36JD, perform the following daily checklist:

Check for loose or missing hardware.

Make sure all connections are tight.

Verify the attachment responds properly to controls.

Check for debris build-up that could obstruct proper motion of the spreader control components.

Ensure that tires on composite (plastic) rims are inflated to 30 psi (2.1 bar) (207 kPa), or tires on metal rims are inflated to 20 psi (1.3 bar) (138 kPa) maximum.

When using the JOHN DEERE LPBS36JD, follow these tips:

Always operate at the designed speed limit of 3 mph.

When backing, move straight to avoid jack knifing which could damage the equipment.

Only tow with designed vehicles, such as riders and lawn and garden tractors.

Do not exceed the maximum weight capacity of 79 kg (175 lb).

Break up any lumps as you fill the hopper.

Avoid using on windy days, especially when spreading fine grass seed or herbicides.

The optimum hitch height is 18 to 23 cm (7 to 9 in.).

The flow control handle should have resistance; increase or decrease spring tension as required to achieve the desired handle resistance.

For normal uniform spreading with the JOHN DEERE LPBS36JD, the directional control plate should be placed close to the center position. If material is coming out too far to the left or right, adjust the plate by moving it to the right or left as needed to center the distribution pattern. For one side only spreading, such as near sidewalks or planting beds, you can adjust the plate to the left side, which provides a 90% shut-off of material to the right side of the vehicle.

To ensure years of service from the JOHN DEERE LPBS36JD, follow these maintenance tips:

Keep the spreader clean and dry.

Do not allow material to remain in the hopper for extended periods.

If rust develops, sand it lightly and paint the area with enamel.

Periodically check all fasteners for tightness.

Rinse and dry the inside and outside of the spreader after each use, moving the flow control as you rinse to avoid material build-up.

If the JOHN DEERE LPBS36JD is dispensing too much or too little, you should calibrate the gage plate.

If the flow control handle on the JOHN DEERE LPBS36JD is stiff or non-functional, the hardware may be too tight. Try loosening the 5/16 x 2-3/4 in. bolt on the flow control handle assembly. Additionally, take the gate and directional control plates apart and clean them thoroughly with soap and water.

If material is clogged in the JOHN DEERE LPBS36JD, turn off the engine, set the parking brake, fully open the gate, and shake the hopper until the material flows, then close the gate.

If the fan on the JOHN DEERE LPBS36JD does not turn, check the following:

Find or replace any missing open-style spring locking pin on the right wheel rim.

Find or replace any missing large closed-style spring locking pin in the transmission.

Check the position of the fan and fan driver.

Check for transmission malfunction: With the spreader attached to your machine, lift the drive wheel and rotate it. Apply gentle pressure to the fan shaft; it should turn with each rotation of the wheel.

If the product you are using is not listed in the provided flow control setting tables, use this calibration guide to set the flow control on your JOHN DEERE LPBS36JD based on the application rate from the product package: