IDEAL 2265 (02) PDF Document

This IDEAL 2265 document shredder is intended for shredding paper. Other materials may damage the shredder.

The hardened solid steel blade shafts are insensitive to small amounts of paper clips and staples. This does not apply to models with 0.8 x 12 mm and smaller particle cut. In this case, the paper to be shred must not contain any paper clips or staples.

Depending on the device model, small amounts of CDs, credit and customer cards as well as discs can also be shred.

Please strictly follow the safety instructions mentioned in the operating manual. This manual must be available at any time.

• Take care of long hair!

• Do not grasp into the cutting mechanism!

• Take care of ties and other loose pieces of clothing!

• Warning, moving parts!

• No operation by children! This device is not suited for use at locations where children might be present!

• Do not destroy accumulators/batteries!

• Do not use any spray cans with flammable content near to the document shredder!

• Do not use any flammable cleaning agents!

• Caution: parts with sharp corners and edges!

• Remove the plug before cleaning the machine!

• Do not perform any repairs on the document shredder!

• Ensure free access to mains.

• Do not operate the machine without the safety flap.

The IDEAL 2265 features an automatic standby that switches off after 15 minutes of inactivity. The machine can be switched off at any time by pressing the power button. When in standby, the green LED control light is off, and there will be no power consumption. Within these 15 minutes before shutting down, the paper shredder uses 0.650 Wh of energy.

1. Place the machine onto the shred bin.

2. Plug the machine into the wall socket.

1. Press the rocker switch quickly: the green light will turn on, and the machine is now ready for operation. The shredder starts automatically when paper is inserted.

2. Press and keep the switch pressed: The machine starts and shreds any remaining paper in the inlet shaft. Afterward, it will resume automatic start when new paper is inserted.

The machine stops automatically when no further paper is inserted. It enters an automatic standby mode that switches off completely after 15 minutes. The machine can be switched off at any time by pressing the switch (this is not possible when the machine is in reverse motion). When the green LED control light is off, there is no power consumption.

The IDEAL 2265 stops automatically if too much paper is inserted. It will automatically reverse if the paper jams, and the “ON/OFF” button will light up red.

1. Remove the jammed paper.

2. Re-feed the paper in smaller quantities.

To interrupt the shredding procedure and manually reverse:

1. Press the green button. The machine will stop, and the button will change to red.

2. Press the red button for any length of time. The machine will run in reverse, and the button will flash green.

3. Remove the paper. The machine is now ready for operation.

Empty the shred bin when it is full. For the IDEAL 2265 model, the fill level can be seen in the window on the front of the cabinet.

Oiling the Shredding Mechanism:

If the sheet capacity reduces or after the shred bin is emptied, you should oil the shredding mechanism. For a straight cut model, use the oiler. For a particle cut model, use the oiler or oil sheets.

Cleaning the Cutting Head:

From time to time, clean the output area of the cutting head.

• Disconnect the machine from the mains.

• Remove paper debris with a brush.

Be aware of the danger of injury from sharp parts.

If the IDEAL 2265 will not start, check the following:

• Is the machine plugged in?

• Is the machine head placed correctly on the shred bin/cabinet?

• For the IDEAL 2265, is the shred bin pushed in completely?

• Is the “ON/OFF” button pressed? The green LED lamp should light up.

• Have you tried feeding paper into the center of the feed opening to activate the photo cell?

If the machine will not stop, the photo cell may be obstructed. Remove the plug from the wall socket and clean the photo cell in the feed opening with a small brush.

The machine switched off due to its protection against overload. Please let the machine cool down before resuming operation.

To ensure trouble-free operation, empty the shred bins in a sufficient amount of time, at least daily, so that no interference is caused to the cutting heads. If a paper jam occurs that cannot be corrected by reversing the motor, it may be because of an overfilled shred bin. The shred bin must be emptied to correct the issue.

For IDEAL 2265 (straight cut):

• Environmentally friendly oil (10 x 0.2 litre). Order No. 9000 611

For IDEAL 2265 CC (particle cut):

• Oil sheets (18 Sheets). Order No. 9000 631

Please remember to respect local regulations. Hand in non-working electrical equipment to an appropriate waste disposal center. The packaging material is recyclable; dispose of the packaging in an environmentally friendly manner and make it available for the recyclable material collection service.

Please think of the environment and dispose of shredded CDs, cards, and other data media separately from shredded paper.