FREE ENGLISH HYGGER HZ012 (01) PDF DOCUMENT.
FREE ENGLISH HYGGER HZ012 (01) PDF USER GUIDE.
FREE ENGLISH HYGGER HZ012 (01) PDF USER MANUAL.
FREE ENGLISH HYGGER HZ012 (01) PDF OWNER GUIDE.
FREE ENGLISH HYGGER HZ012 (01) PDF OWNER MANUAL.
FREE ENGLISH HYGGER HZ012 (01) PDF REFERENCE GUIDE.
FREE ENGLISH HYGGER HZ012 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH HYGGER HZ012 (01) PDF REFERENCE MANUAL.
FREE ENGLISH HYGGER HZ012 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH HYGGER HZ012 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD HYGGER HZ012 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the product specifications for the HYGGER HZ012 Reptile Light Fixture?
Input voltage: AC120V 60Hz
Power: 10W
Light source: LED
Working temperature: -20°C to 80°C
Service life: 12000 hours
Spectrum: UVB+ UVA+ Visible light
Color temperature: White 5000K
12 Inches of UVB radiation: 85µW/cm²
Suitable for pets: Bearded dragons, chameleons, turtles, snakes, frogs, salamanders, etc.
What are the main features of the HYGGER HZ012 light fixture?
1) Highly efficient and energy-saving: With efficient and energy-saving LED bulbs as illuminants, their luminous efficiency is 2-3 times of traditional compact fluorescent lamps.
2) Longer service life: LED bulbs have a longer service life. In addition, the heat dissipation design of the aluminum cover significantly reduces the working temperature of the light board and prolongs the light decay speed of LED bulbs, ensuring a longer service life.
3) Scientific LED bulb configuration: The content of UVA and UVB in the bulbs is similar to the ratio of natural sunlight. The warm white 5000K color temperature used in Full spectrum lamp beads is softer and more comfortable than the 6500K color temperature of fluorescent lamps.
4) Maximum electrical safety: The LED bulbs operate at low voltage and consume less power. The circuit board is not easily damaged, ensuring maximum stability and safety during operation.
How do I prepare and install the HYGGER HZ012 light fixture on top of my reptile terrarium?
Notes before use:
1) Ensure the lamp and its holder are operated in a power-off state.
2) Check whether the lamp and tube are in good condition.
Installation procedures:
1) Connect the “Kettle plug” of the power cord to the “Kettle cord” at either end of the lamp.
2) Before switching on the power supply, ensure that the switch is in the “off state”, meaning the end of the switch with a raised bar is tilted up.
3) Place the lamp holder on the top of the reptile terrarium, which is recommended to be about 12-18 inches (30-45cm) from the bottom.
How do I install the HYGGER HZ012 light fixture under the mesh cover of a terrarium?
1) Insert the long screw upwards into the buckle and embed the buckle at both ends into the top cover of the lamp.
2) Place the lamp in an appropriate position on the mesh cover of the reptile terrarium, and install the gasket, butterfly nut, and nut cover on the bolt in turn.
What are the usage and replacement guidelines for the HYGGER HZ012?
Duration of use: 8-12 hours per day is recommended, and the time can be adjusted as needed.
Regular replacement: Check the fluorescent light regularly for damage or spectral degradation to ensure your pets receive adequate UVB exposure. The UVB radiation level of this product decreases by about 18% after one year of use (3600 hours of operation). Therefore, check when you need to replace the additional light source according to the additional light requirements of the reptile you keep.
What are the important safety warnings and attention points for the HYGGER HZ012?
1) Avoid moisture: This product is not waterproof, do not use it in humid environments, and avoid the lamp contact with water.
2) As with the COB light source in the market, this bulb may dissipate heat during operation. It is normal for the temperature of the aluminum cover to reach about 122°F / 50°C.
3) Keep away from children: Please install the lamp where children can not reach.
CLICK HERE TO DOWNLOAD HYGGER HZ012 (01) PDF DOCUMENT
