HISENSE AP-14DR1SFJS2 (01) PDF MANUAL

HISENSE AP-14DR1SFJS2 (01) PDF SUMMARY:

For questions about features, operation/performance, parts or service, who should I call?

Call 1-877-465-3566.

---

What are the tools needed for installation?

• Phillips screwdriver
• Scissors
• Pencil

---

What parts are supplied for installation?

• Foam seal
• Dummy coupling
• Flexible exhaust hose
• Window exhaust adapter
• 112" screws (2)
• Wood screws(4)
• Window-lock bracket(2)
• Outer slider section panel A
• Inner slider section panel B
• Outer slider section panel D
• Inner slider section panel C
• 3.-fi"screws (2)
• Foam seal (2)
• Foam seal(2)
• Drain hose (1) (Heating Mode)
• Drain hose clip (1) (Heating mode)

---

What are the location requirements for the air conditioner?

• The flexible exhaust hose allows placement of the air conditioner between 23¾" and 64½" (60 cm and 163 cm) from window or door.
• Confirm the correct size air conditioner is being used for the space to be cooled.
• To ensure proper ventilation, keep the required distance from the return air outlet to the wall or other obstacles at least 23¾" (60 cm).
• Do not block the air outlet.
• Provide easy access to the grounded 3 prong outlet.

---

What are the electrical requirements for the air conditioner?

• The portable air conditioner should be dedicated to a 115V, 60 Hz, 15-amp fuse grounded 3 prong outlet.
• The use of a time-delay fuse or time-delay circuit breaker is required.
• All wiring must comply with local and the national electrical codes and be installed by a qualified electrician.

---

How do I test the power supply cord?

1. Plug power supply cord into a grounded 3 prong outlet.
2. Press RESET (on some devices, a green light will turn on).
3. Press TEST (listen for click; Reset button will trip, and on some devices, a green light will turn off).
4. Press and release RESET (listen for click; Reset button will latch, and on some devices, a green light will turn on). The power supply cord is ready for operation.

---

What are the notes about the power supply cord?

• The Reset button must be pushed in for proper operation.
• The power supply cord must be replaced if it fails to trip when the test button is pressed or fails to reset.
• Do not use the power supply cord as an off/on switch. The power supply cord is designed as a protective device.
• A damaged power supply cord must be replaced with a new power supply cord obtained from the product manufacturer and must not be repaired.
• The power supply cord contains no user serviceable parts. Opening the tamper-resistant case voids all warranty and performance claims.

---

What should I do when I unpack the air conditioner?

• Remove and recycle packaging materials.
• Remove tape and glue residue from surfaces before turning on the air conditioner.
• Keep unit upright at least 2 hours prior to use.
• Handle the air conditioner gently.

---

What should I avoid when removing tape or glue?

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue because these products can damage the surface of the air conditioner.

---

What size windows can the window vent panel and extensions fit?

The window installation kit allows you to install the air conditioner in most vertical-sliding windows 18" to 50" wide, or casement-style windows from 18" to 50" high.

---

How do I install the exhaust hose and adapter?

1. Roll the air conditioner to selected location.
2. Stretch the end of the hose. Attach the dummy coupling to the flexible exhaust hose. Turn counter-clockwise until securely locked into place.
3. Attach the window exhaust adapter to the flexible exhaust hose. Turn counter-clockwise until securely locked into place.
4. Insert the dummy coupling into the slot on the back of the air conditioner.
5. Slide down to lock the hose into place.

---

What is the correct way to install in Vertical Sliding Windows?

1. Cut the foam seal M(adhesive type) & N (adhesive type-shorter)to the proper length, and attach it to the window sash and frame.
2. Insert the vent panel assembly, including extension panels, if needed, into the window opening. Extend the extension panels, if used.
3. Cut the foam seal A(Non-adhesive type) to the window width. Stuff the foam seal A between the glass and the window to prevent air and insects from getting into the room.
4. Install the Window-lock bracket with a E or F screw as shown if you need. E screw is suitable for wood window, F screw is suitable for metal window.

---

What is the correct way to install in Horizontal Sliding Windows?

1. Cut the foam seal M(adhesive type) & N (adhesive type-shorter)to the proper length, and attach it to the window sash and frame.
2. Insert the vent panel assembly, including extension panels, if needed, into the window opening. Extend the extension panels, if used.
3. Cut the foam seal A(Non-adhesive type) to the window width. Stuff the foam seal A between the glass and the window to prevent air and insects from getting into the room.
4. Install the Window-lock bracket with a E or F screw as shown if you need. E screw is suitable for wood window, F screw is suitable for metal window.

---

How do I drain the air conditioner (for Heating models only)?

1. Uncover the primary drain port.
2. Attach the drain hose to the primary drain hose.
3. Place the other end of drain hose into an outfall.
4. Check to see that the hose lies flat and is in the drain.
5. Make sure the hose end that goes to the drain is on a lower level than the hose end that connects to the unit.
6. The hose should not be kinked or pinched.

---

What are some important things to remember when operating the portable air conditioner?

• The air conditioner display shows the current room temperature.
• When changing modes while the air conditioner is in operation, the compressor will stop for 3 to 5 minutes before restarting.
• In Cooling or Dry mode, the compressor and condenser fan will stop when the room temperature reaches the set temperature.
• In the event of a power failure, the air conditioner will operate at the previous settings when the power is restored.

---

How do I start my portable air conditioner?

1. Select the mode.
2. Select the fan speed.
3. Set the temperature.
4. Press POWER button to start the air conditioner.

---

How do I select the mode?

1. Press and release MODE until you see the symbol flashes for the operating modes.

2. Choose Cooling, Dry, Fan Only, or Heating.

   • Cooling-Cools the room. Press FAN to select High, Mid, or Low. Press the Plus or Minus button to adjust the temperature.
   • Dry-Dries the room. The air conditioner automatically selects the temperature. The fan runs on Low speed only.
     • NOTE: Dry mode should not be used to cool the room.
   • Fan Only mode. Press FAN to select High, Mid, or Low.
   • Heating-heats the room. Press FAN to select High, Mid, or Low. Press the PLUS or MINUS button to adjust the temperature.
     • NOTE: Heating is NOT available for cooling. To cool, that mode must be selected.

---

How do I select the fan speed?

1. Press and release FAN to choose the desired fan speed.

2. Choose High, Mid, or Low.

   • Auto-automatically controls the fan speed depending on the current room temperature and temperature control setting.
   • High-for maximum fan speed.
   • Mid-for normal fan speed.
   • Low-for minimum fan speed.

---

How do I set the temperature?

• Press the PLUS button to raise the temperature. Press the PLUS button once to increase the set temperature by 1 °F (1 °C).
• Press the MINUS button to lower the temperature. Press the MINUS button once to decrease the set temperature by 1 °F (1 °C).

---

What are the notes about temperature?

• In the Cooling mode, the temperature can be set between 61°F and 86°F (16°C and 30°C).
• In Fan Only mode, the temperature cannot be set.

---

How do I insert the batteries into the remote control?

1. Remove the battery cover along the arrowed direction.
2. Insert new batteries making sure that the(+) and(-) of battery are matched correctly.
3. Re-attach the cover by sliding it back into position.

---

What are the notes about inserting batteries in the remote control?

• Use the included 2 standard AM(1.5volt) batteries. Do not use rechargeable batteries. Replace batteries with new ones of the same type when the display becomes dim, or after 6 months.
• If you reload batteries after removing the old ones, previous settings will be lost.
• Do not recharge non-rechargeable batteries.
• Do not mix different types of batteries such as alkaline, carbon-zinc, or rechargeable batteries.
• Do not mix old and new batteries.
• Batteries are to be inserted with the correct polarity.
• Exhausted batteries are to be removed from the product.

---

How do I use the remote control?

To operate the room air conditioner, aim the remote controller to the signal receptor. The remote control will operate the air conditioner at a distance of up to 23’ (7m) when pointing at signal receptor of the air conditioner.

---

How do I turn the power on or off using the remote control?

Press ON/OFF button to turn on or off the unit.

---

What should I do if the unit does not respond at once when changing modes during operation?

Wait 3 minutes before restarting the appliance.

---

How do I select the mode on the remote control?

1. Press MODE repeatedly until you see the symbol flash for the desired setting.

2. Choose Cooling, Dry, Fan Only, and Heating.

   • Cooling-Cools the room. Press FAN to select AUTO, HIGH, MID or LOW. Press the UP or DOWN button to adjust the temperature.
   • Dry-sets to dry the room. The air conditioner automatically selects the temperature. The fan runs on Low speed only. A decrease or rise of up to 4 °F (2°C) can be set with the remote controller if you still feel uncomfortable.
   • Fan Only-Only the fan runs. Press FAN button to adjust fan speed.
     • NOTE: Auto fan speed cannot be selected in Fan Only mode.
   • Heating-Heats the room. Press FAN to select the fan speed. Press the up or down TEMP button to adjust the temperature.

---

How do I use SMART Mode?

Press the SMART button, regardless If the unit is on or off, to set temperature and fan speed automatically based on the actual room temperature.

---

How do I use the SUPER button?

SUPER button is used to start or stop fast cooling or heating.

1. Press SUPER button. The air conditioner automatically sets the fan speed to High and the temperature to 61 °F (16°C). Fast heating operates at auto fan speed, changing the set temperature automatically to 86°F (30°C).
2. To turn off Super control, press any button on the remote control or control panel except Timer On, Timer Off, Clock, Dimmer, Ifeel and Swing.

---

How do I set the fan speed?

1. Press FAN button, Choose desired fan speed.

   • Auto . High. Medium____. Low
   • Auto-Automatically controls fan speed depending on current room temperature and temperature control setting.
   • NOTE: Auto fan speed cannot be selected in Fan Only mode.
   • High for maximum fan speed
   • Mid for normal fan speed
   • Low for minimum fan speed

---

How do I adjust the temperature?

• Press the UP button to raise the temperature. Press the UP button once to increase the set temperature by 1 °F (1 °C).
• Press the DOWN button to lower the temperature. Press the DOWN button once to decrease the set temperature by 1 °F(1 °C).

---

What are the notes about the temperature?

• In the Cooling and Heating mode, the temperature can be set between 61°F and 86°F(16°C and 30°C).
• In Fan Only mode, the temperature cannot be set.

---

How do I use sleep mode?

SLEEP mode can be set in Cooling, Heating or Dry operation mode. This function gives you a more comfortable environment for sleep.

1. Press MODE to select Cooling, Heating or Dry.
   • NOTE: Sleep control cannot be selected when Fan Only or SMART is selected.
2. Press the UP or DOWN button to set the temperature.
3. Press SLEEP. After 5 seconds, the lights on the control panel display will dim.
   • NOTE: The temperature and airflow direction may be adjusted during Sleep control. The fan speed is automatically set to Low speed. After 5 seconds, the lights on the control panel display will dim again.
4. To turn off Sleep control, press SLEEP, MODE, ON/OFF,FAN, SUPER or wait 8 hours for Sleep control to turn off automatically.

---

What are the notes about sleep mode?

• The appliance will stop operation automatically after operating for 8 hours.
• Fan speed is automatically set at low speed.
• In the Cooling mode, if the current room temperature is below79°F (26°C), the temperature will automatically increase 1 °F(1 °C) during the first hour after Sleep control is activated, then remain the same. If room temperature is79°F(26°C) or above, set temperature will not change.
• In Heating mode, the set temperature will decrease by 6°F (3°C) at most, during 3 hours, then keeps steady.
• The air conditioner will return to previous settings after Sleep control is turned off.

---

How do I use I FEEL?

The temperature sensor built into the remote controller is activated. It can sense its surrounding temperature and transmit the signal back to the unit, when the remote control is pointed towards the air conditioner. The unit can adjust the temperature so as to provide maximum comfort.

---

What are the notes about I FEEL?

• The I FEEL function is active, as a default setting from the factory.
• To de-activate the I FEEL function, press the I FEEL button for about 5 seconds, and the transmit signal in the display will disappear, the I FEEL function will be de-activated.
• Pressing the I FEEL button once will activate I FEEL function again.

---

How do I use the dimmer?

Press the DIMMER button to turn off the light and the control panel display.

---

What are the notes about the dimmer?

When in DIMMER mode, new control inputs will return lighting and display to normal.

---

How do I use the clock function?

1. You can set or adjust the real time by pressing CLOCK button.
2. Use the Up and Down buttons to set the correct time.
3. Press CLOCK button again once the real time is set.

---

How do I use the TIMER?

The TIMER ON button can be used to turn on the unit automatically at the time you set.

1. Press TIMER ON, Then “On 12:00” flashes on the LCD.

2. Press the UP or DOWN button to get your desired time of day to turn on the appliance.

   • Press the UP or DOWN button once to increase or decrease the time setting by 1 minute.
   • Press and hold the UP or DOWN button for 2 seconds to increase or decrease the time setting by 10 minutes.
   • Press and hold the UP or DOWN button for a longer time to increase or decrease the time setting by 1 hour.

3. When the desired time is displayed on the LCD, press the TIMER ON button to confirm it.

---

How do I cancel Timer On?

Press TIMER ON button again, when a “beep” can be heard and the indicator disappears, the TIMER ON mode has been canceled.

---

How do I use SWING?

Press SWING once to change vertical airflow direction. Press again to hold the airflow louver at desired direction.

---

What are the notes about SWING?

• Airflow is automatically adjusted to a certain angle in accordance with the operation mode after turning on the unit.
• The direction of airflow can be also adjusted to your own requirement by pressing the SWING button.
• Do not turn the vertical adjustment louvers manually, to prevent damage.
• Turn off the unit first and cut off the power supply, then restore power again to reset the louver.

---

What are the normal sounds I may hear when my air conditioner is operating?

• Air movement from the fan.
• Clicks from the thermostat cycling.
• Vibrations or noise due to poor wall or window construction.
• A high-pitched hum or pulsating noise caused by the high-efficiency compressor cycling on and off.

---

How do I drain the air conditioner?

1. Unplug the air conditioner or disconnect power.
2. Move the air conditioner to a drain location or outside.
3. Remove the primary drain cover and plug.
4. Drain water completely through the drain hole.
5. Reinstall the drain plug to the primary drain hole.
6. Reinstall the primary drain cover to the drain hole.
7. Reposition the air conditioner.
8. Plug in the air conditioner or reconnect power.

---

How do I clean the outside of the air conditioner?

1. Press ON/OFF to turn off the air conditioner.
2. Unplug the air conditioner or disconnect power.
3. Remove the air filter and clean separately.
4. Wipe the outside of the air conditioner with a soft, damp cloth.
5. Plug in the air conditioner or reconnect power.
6. Press ON/OFF to start the air conditioner.

---

How do I clean the air filter?

1. Press ON/OFF to turn off the air conditioner.
2. Open the filter panel door on the back of the air conditioner and remove.
3. Remove the air filter from the filter panel door.
4. Remove the tapping screw from the condenser air intake filter panel door and remove.
5. Remove the air filter from the filter panel door.
6. Use a vacuum cleaner to clean the filter.
7. If the filter is very dirty, wash the filter in warm water with a mild detergent.
   • Do not wash the filter in the dishwasher or use any chemical cleaners.
8. Air dry the filter completely before replacing to ensure maximum efficiency.
9. Reattach the air filter to the filter panel door.
10. Reinstall the filter panel door and tapping screw.
11. Press ON/OFF to start the air conditioner.

---

How do I store the air conditioner after use?

1. Drain the water completely.
2. Run the air conditioner set to Fan Only for approximately 12 hours to dry the air conditioner.
3. Unplug the air conditioner.
4. Remove the flexible exhaust hose and store with the air conditioner in a clean, dry area.
5. Remove the window kit and store with the air conditioner in a clean, dry area.
6. Remove the filter and clean.
7. Clean the outside of the air conditioner.
8. Reinstall the filter.
9. Remove the batteries and store the remote control with the air conditioner in a clean, dry area.

---

What should I do if the air conditioner will not operate?

• The power supply cord is unplugged. Plug into a grounded 3 prong outlet.
• Time-delay fuse or circuit breaker of the wrong capacity is being used. Replace with a time-delay fuse or circuit breaker of the correct capacity.
• The power supply cord has tripped (Reset button has popped out).
  • Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.
• A household fuse has blown, or a circuit breaker has tripped.
  • Replace the fuse, or reset the circuit breaker.
• The On/Off button has not been pressed. Press ON/OFF.
• The local power has failed. Wait for power to be restored.

---

What should I do if the air conditioner blows fuses or trips circuit breakers?

• Too many appliances are being used on the same circuit. Unplug or relocate appliances that share the same circuit.
• You are trying to restart the air conditioner too soon after turning off air conditioner.
  • Wait at least 3 minutes after turning off air conditioner before trying to restart the air conditioner.
• You have changed modes.
  • Wait at least 3 minutes after turning off air conditioner before trying to restart the air conditioner.

---

What should I do if the air conditioner power supply cord trips (Reset button pops out)?

• Disturbances in your electrical current can trip (Reset button will pop out) the power supply cord.
  • Press and release RESET (listen for click; Reset button will latch and remain in) to resume operation.
• Electrical overloading, overheating, cord pinching or aging can trip (Reset button will pop out) the power supply cord.
  • After correcting the problem, press and release RESET (listen for click; Reset button will latch and remain in) to to resume operation. If the power cord fails to reset, contact a service technician.

---

What should I do if the air conditioner seems to run too much?

• Is there a door or window open? Keep doors and windows closed.
• The current air conditioner replaced an older model.
• The air conditioner is in a heavily occupied room, or heat­ producing appliances are in use in the room.

---

What should I do if the air conditioner runs for a short time only, but the room is not cool?

Set temperature is close to room temperature. Lower set temperature.

---

What should I do if the display shows error code E5?

If the unit display error code E5, it is water full in the unit, you should drain the water. After draining, you can operate the unit again.

---

What should I do if the display shows error code E1/E2/E3/E4/EA?

If the unit display error code E1/E2/E3/E4/EA, please contact customer service.

---

What should I do if the air conditioner runs, but does not cool?

• The filter is dirty or obstructed by debris. Clean the filter.
• Air outlet is blocked. Clear air outlet.
• Set temperature is too high. Lower set temperature.

---

What should I do if the air conditioner cycles on and off too much?

• The air conditioner is not properly sized for your room.
• The filter is dirty or obstructed by debris. Clean the filter.
• There is excessive heat or moisture open container cooking, showers, etc. ) in the room.
• The louvers are blocked.

---

What should I do before calling for assistance or service?

Please check the troubleshooting section of your user manual. It may save you the cost of a service call.