HISENSE 65M7000UWG (01) PDF MANUAL

Be sure to disconnect the A/C power cord before installing a stand or Wall-Mount brackets.

The LED display is very fragile, and must be protected at all times when installing the base stand. Be sure that no hard or sharp object, or anything that could scratch or damage the LED display, comes into contact with it. DO NOT exert pressure on the front of the TV at any time because the screen could crack.

Follow the illustrations and instructions below to complete the installation steps:

1. Carefully place your TV face-down on a soft, flat surface to prevent damage to the TV or scratching to the screen.

2. Secure the 2 Column bases to the Base stand with the 4 screws in accessary tightly.

3. Align the Base support with the screw holes on the bottom of TV BACK, secure the Base support to the TV with the 6 screws (50″/55″) / 7 screws (65″/70″) in accessary tightly.

Connect the antenna or cable to the TV JACK labeled ANT.

Insert the CI+ module into the TV JACK labeled COMMON INTERFACE.

Before you insert/remove the CI+ module, ensure that the TV is switched off. Then insert the Cl card into the CI+ module in accordance with the Service Provider’s instructions.

Do not repeatedly insert or remove the Common Access Module as this may damage the interface and cause a malfunction.

You must obtain a CI+ module and card from the service provider of the channels you want to watch.

Insert the CI+ module with the SmartCard in the direction marked on the module and SmartCard.

CI+ is not supported in some countries and regions; check with your authorized dealer.

Connect a HDMI / Comp / AV cable from an external A/V equipment. No sound connection is needed for HDMI to HDMI connection. If the signal resolution does not match the specification table, you need to change the setting of device according to the table. Please consult your device user manual for instruction.

To select the HDMI / Component / AV, press [Input] button, when the list of input Source appears, press [< / >] to select the source [HDMI] / [COMPONENT] / [AV], then press [OK] to connect.

Connect an HDMI cable from an external digital audio system to the TV JACK labeled HDMI 2(ARC).

ARC enables the TV to directly output the digital sound through an HDMI cable. Please note that it works only when the TV is connected to the audio receiver that supports the ARC (Audio Return Channel) function.

When this jack is used as the ARC function, it can’t be used as signal input at the same time.

Connect an MHL cable (not provided) from your MHL-enabled device, such as a cell phone to the TV JACK labeled HDMI 1(MHL).

MHL is only available through HDMI 1(MHL) and only when the TV is connected to compatible MHL devices. Please note that not all MHL devices are supported.

Connect Headphone for audio out of the TV to the TV JACK labeled HEADPHONE.

The built-in speakers will be disabled once the headphone is connected.

Please make sure that the headphone you plug in is without microphone function, or it may not be supported.

Connect an digital audio cable from an external digital audio system to the TV JACK labeled DIGITAL AUDIO OUT.

Optical SPDIF is a type of digital audio interconnect cable used in consumer audio equipment to output audio over reasonably short distances. The signal is transmitted over a digital audio cable.

Before connecting a digital audio system to the DIGITAL AUDIO OUT jack, you should decrease the volume of both the TV and the system to avoid that the volume suddenly become bigger.

Connect the USB1.1, USB2.0 and USB3.0 devices such as hard drives, USB sticks and digital cameras for browsing photos, listening music and watching recorded movies to the TV JACKS labeled USB 2, USB 1, USB 3.

You can record live TV program (refer to PVR in User Manual). At the same time update is also an easy thing and will be done just by plugging the USB with the updating files into the USB interface.

When connecting a hard disk or a USB hub, always connect the mains adapter of the connected device to the power supply.

If a USB 1.1 or USB2.0 device requires more than 500mA or 5V, the USB device may not be supported. Max supported current for USB 3.0 device is 1A. Exceeding the max supported current may result in damage or data loss.

If you want to store the video streaming of a DTV program, the transfer rate of the USB storage device must not be less than 5MB/s. Approximately 20GB of storage is required to record 2.5 hours of HD video.

Connect your TV to your network by connecting the LAN port on the back of your TV to an external modem or router using a LAN (Ethernet/Cat 5) cable.

We recommend to use a modem or router that supports Dynamic Host Configuration Protocol (DHCP). Modems and routers that support DHCP automatically provide the IP address, subnet mask, gateway, and DNS, so you don’t have to enter them manually. Most home networks already have DHCP.

Connect your TV to your wireless network, you need a wireless router or modem.

The TV’s built-in Wireless LAN Adapter supports the IEEE 802.11 ac/b/g/n communication protocols. We recommend using IEEE 802.11ac router. Low transfer rates for b/g/n may have the influence on the quality of streamed videos and other media.

You must use the built-in Wireless LAN Adapter to use a wireless network because the set doesn’t support external USB network adapter.

If the wireless router supports DHCP, your TV can connect more easily to the wireless network.

If you apply a security system other than the systems listed below, it will not work with the TV.

Security system: WPA, WEP, WPA2.

In order to guarantee smooth network, the distance between router and TV is less than 10 meters.

1. Slide the back cover to open the battery compartment of the remote control.

2. Insert two AAA size batteries. Make sure to match the ( + ) and ( – ) ends of the batteries with the (+) and ( – ) ends indicated in the battery compartment.

3. Close the battery compartment cover.

The remote control can work at a distance of up to 8 meters in front of the TV set.

The remote control angle: taking the remote sensor as an apex, 6 meters away, its controlled horizontal angle is within ±30°, while the vertical angle is within ±15°.

The operating distance may vary depending on the brightness of the room.

1. Connect the mains cable to the mains socket after you have completed all the connections.

2. The first time you turn the TV on, it will go straight into the Installation Guide. It will assist you to specify the Language, Location and Network.

3. Press the [ ^ / v / < / >] to navigate the menu and change the settings. Press the [OK] button to confirm.