FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF DOCUMENT.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF USER GUIDE.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF USER MANUAL.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF OWNER GUIDE.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF OWNER MANUAL.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF REFERENCE GUIDE.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF REFERENCE MANUAL.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH HANNA INSTRUMENTS HI7640-1805 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD HANNA INSTRUMENTS HI7640-1805 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I wire the probe to the controller?
1. Disconnect the controller from power. Run the probe cable through the conduit opening.
2. Connect the probe leads to the removable terminal connector marked PROBE. Follow lead markings (-/+) to ensure correct wiring position for output leads.
3. Carefully put the wired terminal connector into place on the board.
4. Position excess cable through the cable gland before tightening the nut.
5. Remove the ground screw and hardware located below the PROBE connector. Attach the ground lead.
What is the probe cabling color code?
| Marking | Attached Cable | Patch Cable | Functionality |
|---|---|---|---|
| – | GREEN | BLACK | 0 V |
| B | WHITE | WHITE | RS485 D- |
| A | YELLOW | BLUE | RS485 D+ |
| + | BROWN | RED | 5 V |
| Ground Symbol | GREEN-YELLOW | GREEN-YELLOW | PROTECTIVE GROUND |
How do I connect the probe?
Align the pins and key then push the plug into the socket. Rotate the collar to lock in place.
What are the HI510 Controller supported probe series and configurations?
HI110 X X | Y 8 Z Z – pH & Temperature
| XX Junction Type | Y Glass Sensor | Matching Pin | pH range | Temperature range |
|---|---|---|---|---|
| 06 PTFE junction | 1 Low temperature | Titanium | 0.00 to 12.00 pH | -5.0 to 80.0 °C (23.0 to 176.0 °F) |
| 16 Ceramic junction | 3 High temperature | 0.00 to 14.00 pH | 0.0 to 100.0 °C (32.0 to 212.0 °F) | |
| 4 Fluoride resistant | 0.00 to 10.00 pH | -5.0 to 60.0 °C (23.0 to 140.0 °F) |
HI20 X X | Y 8 Z Z – ORP & Temperature
| XX Junction Type | Y Sensor Type | mV range | Temperature range |
|---|---|---|---|
| 04 PTFE junction | 1 Platinum | ± 2000 mV | –5.0 to 100.0 °C (23.0 to 212.0 °F) |
| 14 Ceramic junction | 2 Gold |
HI7630 – | Y 8 Z Z – Conductivity & Temperature
| Y | Cell Type | Measurement | Range |
|---|---|---|---|
| 2 | Two-electrode cell conductivity, AISI 316 stainless steel cell constant k ≈ 0.1/cm | EC | 0.000 µS/cm to 30.00 mS/cm |
| TDS | 0.000 mg/L to 15.00 g/L (TDS factor 0.5) | ||
| RES | 34 Ω•cm to 99.99 MΩ•cm | ||
| Temperature | 0.0 to 50.0 °C (32.0 to 122.0 °F) | ||
| 4 | Four-ring conductivity, platinum on glass, cell constant k ≈ 1.0/cm | EC | 0.0 µS/cm to 999.9 mS/cm |
| TDS | 0.0 mg/L to 400.0 g/L (TDS factor 0.5) | ||
| RES | 1.00 Ω•cm to 9.99 MΩ•cm | ||
| Seawater Salinity | 400.0 %NaCl, 42 psu, 80 ppt | ||
| Temperature | 0.0 to 100.0 °C (32.0 to 212.0 °F) |
HI7640 – 1 8 Z Z – Galvanic Dissolved Oxygen & Temperature
Galvanic sensor
| Concentration | 0.00 to 50.00 mg/L (ppm) |
| Saturation | 0.0 to 500.0 % |
| Temperature | –5.0 to 50.0 °C (23.0 to 122.0 °F) |
HI7640 – 5 8 Z Z – Optical Dissolved Oxygen & Temperature
Optical sensor
| Concentration | 0.00 to 50.00 mg/L (ppm) |
| Saturation | 0.0 to 500.0 % |
| Temperature | –5.0 to 50.0 °C (23.0 to 122.0 °F) |
ZZ Codes
| 8 | Smart probe, with RS485 connection |
| ZZ |
00 supplied with DIN connector (without cable) 05, 10, 15, 25, 50 fixed cable length (in meters) |
CLICK HERE TO DOWNLOAD HANNA INSTRUMENTS HI7640-1805 (01) PDF DOCUMENT