GENKINNO P2 (01) PDF MANUAL

1 x Genkinno P2

1 x Water Filter Tank (Filter Included)

1 x Charger

1 x User Manual

1 x Floating Cable

1 x Handle

1. Drain

2. Charge Input

3. Power Button

4. Battery Level LED

5. Function LED

6. Floating cable

7. Handle

8. Release Button

9. Anti-collision Rubber

10. Wheel

Before using it for the first time, connect the cleaner and the included charger to charge the battery.

– Before charging, check the charging port and keep it dry.

– When the red indicator light of the adapter is on, the battery is currently charging.

– When the green indicator light of the adapter is on, charging has been completed.

Press the start button once to power on the cleaner. When the white light flashes, the cleaner is in preheating mode. After about 30 seconds, the cleaner’s indicator light turns constant blue, indicating that the cleaner is ready to start working.

The battery level is indicated by a light:

Green: The cleaner can work normally.

Red: The battery level is low, and the battery requires recharging.

To power on the cleaner, open the app and tap Add New Device. Then select Genkinno P2 to enter the search page. Once the list displays the relevant product name, tap to complete the initial binding process.

In the app, tap Firmware Upgrade to update the firmware to the latest version. This process takes approximately 2 minutes.

Release it slowly and let it sink steadily to the floor of the pool. Once turned on, the cleaner enters Auto Mode by default, where the cleaner begins to operate approximately 0.5 to 1 minutes after being placed inside the pool.

– The default power of the cleaner is 40W.

– The cleaner’s maximum suction power of 100W will be activated automatically when the cleaner encounters large leaves and other debris.

When the battery is low, the cleaner will park itself so that you can easily take it out.

Locate and grab the floating cable, you can then pull the cable to take the cleaner out from the swimming pool.

Control Stick

Mode Switch Button

Power Switch Button

Function LED

Battery Buckles

(The Power Switch button is changed to the Start/Stop button.)

Please insert three AA batteries into the remote controller as shown in the diagram, and then pair the remote controller with the robotic pool cleaner.

1. Simultaneously press and hold the mode switch button and the power button until the remote controller turns on.

2. Then press the mode switch button twice and wait for the green and blue lights to flash alternately.

3. Turn on the cleaner, wait to hear a “beep,” and see the remote controller LED light turn constant blue, indicating successful pairing.

Turn on the remote controller, press the Mode button. The LED indicator turns green, indicating that the cleaner is switched to manual mode.

Press the Start/Stop button to control the cleaner’s start and stop. When the indicator light is green/blue constant, the cleaner is turned on. When the indicator light is flashing, the cleaner has stopped working.

Use the control stick to move the cleaner Forward, Backward, Turn Left, and Turn Right.

It is highly recommended to clean the filter after each cleaning cycle.

1. Press the release button.

2. Pull out of the water filter tank.

3. Open the water filter tank.

4. Clean the water filter tank.

– After each use, please promptly charge the cleaner to ensure its readiness for the next use.

– Once fully charged, remember to promptly attach the charging plug.

The Genkinno P2 supports connecting to the app for managing the Cleaner. You can access the following services:

– Manage the Cleaner and perform firmware upgrades.

– Obtain pool and Cleaner maintenance knowledge for better pool management.

– Contact the official support team to receive timely technical assistance.

– Please ensure that the cleaner is turned off.

– Ensure that no water is left inside the cleaner and keep it dry.

– Thoroughly clean the filter net and cleaner.

– Store the cleaner indoor away from direct sunlight or weather elements such as rain or frost.

– If the cleaner needs to be stored for a long period of time, it should be charged every three months to maintain battery life between 40%-60%.

– During winter, please store the cleaner indoors to prevent any damage to the cleaner.

PC102

Cleaning Module

Battery

Remote

1. The cleaner cannot power on while being connected to the charger. Please unplug the charger and try to power it on again.

2. If the issue persists, it might be due to the cleaner’s battery being depleted. Connect the charger to charge the cleaner. Once the charger indicator light changes from red to green, unplug the charger and attempt to power it on again.

1. Check if the charger is in good condition. First, plug the charger directly into a power source and observe if the indicator light on the charger is illuminated. If the charger’s indicator light doesn’t turn on, the charger is faulty.

2. If the power indicator light is functioning properly and the cleaner’s power indicator light turns green when connected to the power source, there might be an issue with the cleaner. Please contact us for assistance.

1. If the cleaner’s battery indicator light is red, the cleaner is running out of battery. Please charge the cleaner.

2. If the cleaner’s battery indicator light is green, please check the filter net in the filter water tank to ensure it is not blocked.

When the cleaner’s power is turned on and the white light is flashing, the cleaner is in the startup process. Wait for about 1 minute, and once the cleaner’s light turns constant blue, the cleaner is ready to perform the cleaning tasks.

The remote controller and the cleaner may not be paired. Please follow the user manual to pair the cleaner and remote controller and then try again.

– Only use the accessories recommended or sold by the manufacturer.

– Do not allow children to ride on the cleaner or play with it.

– Use the original and authorized power adapter only.

– The charging adapter must be connected to a leakage-protected socket when charging.

– Do not operate the cleaner when people or animals are in the pool.

– While charging, the cleaner should be uncovered and kept in a cool place in order to prevent damage of internal electrical components caused by overheating.

– Only certified professionals can disassemble the sealed driving kit of the cleaner.

– Do not operate the cleaner while the pool filter is running.

– Oil sealant for the servo contains grease, which can cause water pollution if exposed.

– If the cleaner needs to be stored for a long period of time, it should be charged every three months to maintain battery life between 40%-60%.

– Please use the original and authorized power adapter only. If the cleaner is not charged for a long time, the battery voltage will be lower than the over-discharge protection voltage due to the self-discharge of the battery, which may cause fatal damage.

– Do not use or store the cleaner near any heat source.

– Do not pierce the shell of the cleaner with nails or other sharp objects.

– Do not hammer, impact, or throw the cleaner.

– Make sure the charging socket is dried before charging.

– Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

– This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

– This radio is designed for and classified as “General population/uncontrolled Use”, the guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.

– Check the wheels to make sure they turn properly.

– Always clean and wash the filter tray after using.

– Turn off the cleaner when maintaining, cleaning, or when it is not in use.

– The cleaner should be stored in a cool and ventilated place, away from direct sunshine.

– Due to the limitations of the battery capacity, the cleaner is only suitable for swimming pools with sizes up to 1076 sq. ft (100m²); otherwise, the cleaning effect will be impacted or reduced.

– This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.

– Children shall not play with the appliance.

– Cleaning and user maintenance shall not be made by children without supervision.