GRINDMASTER-CECILWARE 890 (01) PDF Document

The specifications for the GRINDMASTER-CECILWARE 890 models are as follows:

The dimensions in inches for the GRINDMASTER-CECILWARE 890 models are as follows:

For your safety and the safety of others, read all warnings and the operator’s manual before installing or using the product. The following warnings must be observed:

• Product must be attached to a three wire 120V 15 AMP receptacle (export units – 230V 16 AMP).

• Do not deform plug or cord.

• Follow national and local electrical codes.

• Do not use near combustibles.

• Use only on a circuit load that is properly protected and capable of the rated load.

• Always unplug unit from power supply before servicing or cleaning.

FAILURE TO COMPLY RISKS PERSONAL INJURY, SHOCK HAZARD, FIRE, OR DAMAGE TO EQUIPMENT.

To prevent personal injury, please observe the following cautions:

• Personal injury hazard. Keep fingers, hands, and foreign objects out of hopper or chute opening.

• Model 890T must be bolted to the counter to prevent possible bodily injury from overturning.

• Risk of bodily injury due to tipping. Use care when installing Model 890T.

Please take note of the following before installation and operation:

• Never connect to an overloaded circuit or to an extension cord, otherwise serious damage to the motor may result.

• It is essential that full voltage and amperage always be available as it takes full power to grind coffee.

Please read the manual before operating the grinder. Follow these installation steps:

1. Carefully remove grinder from carton.

2. Place grinder in position on shelf, counter or other flat surface.

3. (Model 890T only). Using (4) provided 5/16″-18 x 1 1/2″ bolts, washers, and nuts, attach grinder securely to counter.

4. Plug grinder into the specified power source. (Check rating plate on back of unit for voltage and amperage requirements.) Do not use an extension cord.

5. Fill hopper with whole bean coffee.

6. Grind a small amount of whole bean coffee following operating instructions.

7. If there is any problem, consult the Troubleshooting Guide.

To operate your GRINDMASTER-CECILWARE 890, follow these steps:

1. Turn the selector knob to the desired grind setting.

2. Fill the hopper with the desired type and amount of whole bean coffee. Close the lid.

3. Place the bag underneath the spout.

4. Press the start button.

5. The grinder will automatically stop when the bag is removed. The stop button may be pressed after the grinder has completed grinding.

6. Remove bag from coffee spout once coffee is ground.

Tools required: Phillips screwdriver, Large blade screwdriver, Pliers.

1. Remove all coffee from the hopper.

2. Set selector knob to the finest setting (Espresso or Turkish) depending on the model.

3. Loosen both knob retainer screws in selector knob one turn only.

4. While pressing the bag switch, located behind the spout, press the start button so that the grinder will run during adjustment.

5. With the grinder still running, turn the adjusting screw in the center of the selector knob slowly to the right until a slight chirping noise is heard. Immediately turn the adjusting screw to the left until chirping noise stops. This is the finest grind obtainable.

6. Tighten both of the knob retainer screws. Once the finest grind has been set, the other grind settings will automatically set correctly.

7. Press the stop or off button.

NOTICE: Always be sure the grinding burrs are not touching while the machine is running on the ESPRESSO/TURKISH setting. Otherwise serious damage to the motor may result.

This grinder is equipped with a circuit breaker to protect the motor from overloading. When the circuit breaker trips, the reset button will pop out approximately 1/4″ which stops the power to the grinder. The reset button is located on the front panel.

To reset the circuit breaker, wait two minutes then push in the reset button. You will hear a click as it resets. If the grinder does not operate after resetting the circuit breaker, there may be an obstruction in the grinding mechanism that is stalling the motor. Turn the grind selector knob all the way to the left. Try restarting the grinder. If the circuit breaker “trips” again, the obstruction was not able to pass. In this case, the Grinder Head should be cleaned out as described in the Shear Disc Replacement section.

Follow these cleaning instructions:

NOTICE: The person cleaning the parts should do so with clean hands.

• The outside of the machine can be cleaned with warm soapy water and a damp cloth.

• Grinding parts should be cleaned with a stiff brush or dry cloth. DO NOT USE WATER. See the Shear Pin Replacement section for instructions on assembling and disassembling grinder parts. Before reassembling, wipe motor shaft with dry cloth.

• All other parts that are in contact with food must be washed with warm soapy water, rinsed, and air-dried.

None required.

If the motor should run and no coffee is dispensed, the Shear Pin may have sheared. Should this occur, perform the following operations. Tools required: Slotted Screwdriver, Pliers.

WARNING: Unplug grinder to prevent electrical shock.

1. Remove all of the coffee beans from the hopper.

2. Remove the Grinder Cap by taking out the 2 Cap Screws.

3. Turn Feedworm Assembly such that the slot in the assembly is vertical then push inward to release the Shear Pin.

4. Pull out the Rotary Burr and Feedworm Assembly. Clean out the Grinder Head, removing all coffee particles from inside of the Grinder Head and the Grinder Cap so that it can be reset properly.

5. Check that no obstruction has been caught on the surface of the teeth of either burr. Remove the Shear Cover and broken pieces of the Shear Pin. You are now ready to reassemble the grinder mechanism.

6. Slide the Rotary Burr and Feedworm Assembly onto the Drive Shaft.

7. Align slot in Feedworm Assembly with the hole in the motor shaft. Install new Shear Pin.

8. Reassemble the Shear Cover and Grinder Cap. Make certain the Grinder Cap is screwed on tight and is sealed properly against the head and not tilted or misaligned. Otherwise, a proper grind cannot be obtained.

9. Your grinder is now ready to grind.

If the grinder will not start, check for the following possible causes and solutions:

If the grinder runs or hums but dispenses no coffee, check for the following possible causes and solutions:

If you are experiencing an excessive amount of coffee chaff flying about, check for the following possible causes and solutions:

If the circuit breaker continuously trips, check for the following possible causes and solutions: