GRINDMASTER-CECILWARE 810 (01) PDF Document

The specifications for the GRINDMASTER-CECILWARE 810 model are as follows:

The dimensions for the GRINDMASTER-CECILWARE 810 model are provided in the table below (in inches):

For your safety and the safety of others, please adhere to the following warnings when using the GRINDMASTER-CECILWARE 810:

WARNING:

• Product must be attached to a three wire 120V 15 AMP receptacle (export units – 230V 16 AMP).

• Do not deform plug or cord.

• Follow national and local electrical codes.

• Do not use near combustibles.

• Use only on a circuit load that is properly protected and capable of the rated load.

• Always unplug unit from power supply before servicing or cleaning.

FAILURE TO COMPLY RISKS PERSONAL INJURY, SHOCK HAZARD, FIRE, OR DAMAGE TO EQUIPMENT.

CAUTION:

Personal injury hazard. Keep fingers, hands, and foreign objects out of hopper or chute opening.

NOTICE:

Never connect to an overloaded circuit or to an extension cord, otherwise serious damage to the motor may result.

Please follow these steps to install your GRINDMASTER-CECILWARE 810:

1. Carefully remove the grinder from the carton.

2. Place the grinder in position on a shelf, counter, or other flat surface.

3. Plug the grinder into the specified power source. (Check the rating plate on the back of the unit for voltage and amperage requirements.) Do not use an extension cord.

4. Fill the hopper with whole bean coffee.

5. Grind a small amount of whole bean coffee following the operating instructions as described in this manual.

6. If there is any problem, consult the Troubleshooting Guide in this manual.

NOTICE: It is essential that full voltage and amperage always be available as it takes full power to grind coffee.

To operate your GRINDMASTER-CECILWARE 810 coffee grinder, follow these steps:

1. Turn the selector knob to the desired grind setting.

2. Fill the hopper with the desired type and amount of whole bean coffee. Close the lid.

3. Place the bag underneath the spout.

4. Press the grinder switch to the ON position.

5. The grinder will automatically stop when the bag is removed. Once coffee is ground, press the grinder switch to the OFF position or the grinder will continuously run.

6. Remove the bag from the coffee spout once the coffee is ground.

To adjust the grind setting on your GRINDMASTER-CECILWARE 810, you will need a Phillips screwdriver, a large blade screwdriver, and pliers. Follow these steps:

1. Remove all coffee from the hopper.

2. Set the selector knob to the finest setting (Espresso or Turkish), depending on the model.

3. Loosen both knob retainer screws in the selector knob one turn only.

4. While pressing the bag switch (located behind the spout), press the ON or START button so that the grinder will run during adjustment.

5. With the grinder still running, turn the adjusting screw in the center of the selector knob slowly to the right until a slight chirping noise is heard. Immediately turn the adjusting screw to the left until the chirping noise stops. This is the finest grind obtainable.

6. Tighten both of the knob retainer screws. Once the finest grind has been set, the other grind settings will automatically set correctly.

7. Press the STOP or OFF button.

NOTICE: Always be sure the grinding burrs are not touching while the machine is running on the ESPRESSO/TURKISH setting. Otherwise, serious damage to the motor may result.

The GRINDMASTER-CECILWARE 810 is equipped with a circuit breaker to protect the motor from overloading. When the circuit breaker trips, the reset button will pop out approximately 1/4″, stopping power to the grinder. The reset button is located on the front panel of the Model 810, 835, and 875.

To reset the circuit breaker, wait two minutes, then push in the reset button. You will hear a click as it resets. If the grinder does not operate after resetting the circuit breaker, there may be an obstruction stalling the motor. Turn the grind selector knob all the way to the left and try restarting the grinder. If the circuit breaker “trips” again, the obstruction was not able to pass. In this case, the Grinder Head should be cleaned out as described in the Shear Disc Replacement section of the manual.

Cleaning Instructions

NOTICE: The person cleaning the parts should do so with clean hands.

The outside of the machine can be cleaned with warm soapy water and a damp cloth.

Grinding parts should be cleaned with a stiff brush or dry cloth. DO NOT USE WATER. See the Shear Disc Replacement section for instructions on assembling and disassembling grinder parts. Before reassembling, wipe the motor shaft with a dry cloth.

All other parts that are in contact with food must be washed with warm soapy water, rinsed, and air-dried.

Lubrication

None required.

If the motor runs but no coffee is dispensed, the shear disc may have sheared. You will need a slotted screwdriver and pliers. Follow these steps:

WARNING: Unplug the grinder to prevent electrical shock.

1. Remove all of the coffee beans from the hopper.

2. Remove the Grinder Cap by taking out the 2 Cap Screws.

3. Pull out the Rotary Burr and Feedworm Assembly. Clean out the Grinder Head, removing all coffee particles from inside of the Grinder Head and the Grinder Cap so that it can be reset properly.

4. Check that no obstruction has been caught on the surface of the teeth of either burr. Remove the Shear Cover and broken pieces of the Shear Disc.

5. Slide the Rotary Burr and Feedworm Assembly onto the Drive Shaft. For Models 810, 835, 875, insert the shear drive so that the Motor Shaft tongue engages into the shear drive notch.

6. For Models 810, 835, 875, insert a new Shear Disc by aligning the slot in the Shear Drive with the slot in the hub of the Feedworm.

7. Reassemble the Shear Cover and Grinder Cap. Make certain the Grinder Cap is screwed on tight and is sealed properly against the head and not tilted or misaligned. Otherwise, a proper grind cannot be obtained.

8. Your grinder is now ready to grind.

If your GRINDMASTER-CECILWARE 810 grinder will not start, check the following possible causes and solutions:

If your GRINDMASTER-CECILWARE 810 runs or hums but dispenses no coffee, check the following possible causes and solutions:

If there is an excessive amount of coffee chaff flying about from your GRINDMASTER-CECILWARE 810, review these potential causes and their solutions:

If the circuit breaker on your GRINDMASTER-CECILWARE 810 continuously trips, please check these possible causes and solutions: