GRINDMASTER-CECILWARE 875 (01) PDF Document

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

For your safety and the safety of others, read all warnings and the operator’s manual before installing or using the product.

DANGER: This term warns the user of imminent hazard that will result in serious injury or death.

WARNING: This term refers to a potential hazard or unsafe practice, which could result in serious injury or death.

CAUTION: This term refers to a potential hazard or unsafe practice, which could result in minor or moderate injury.

NOTICE: This term refers to information that needs special attention or must be fully understood.

WARNING

• Product must be attached to a three wire 120V 15 AMP receptacle (export units – 230V 16 AMP).

• Do not deform plug or cord.

• Follow national and local electrical codes.

• Do not use near combustibles.

• Use only on a circuit load that is properly protected and capable of the rated load.

• Always unplug unit from power supply before servicing or cleaning.

FAILURE TO COMPLY RISKS PERSONAL INJURY, SHOCK HAZARD, FIRE, OR DAMAGE TO EQUIPMENT.

CAUTION

Personal injury hazard. Keep fingers, hands, and foreign objects out of hopper or chute opening.

NOTICE

Never connect to an overloaded circuit or to an extension cord, otherwise serious damage to the motor may result.

NOTICE: It is essential that full voltage and amperage always be available as it takes full power to grind coffee.

Please read the manual before operating the grinder.

1. Carefully remove grinder from carton.

2. Place grinder in position on shelf, counter or other flat surface.

3. Plug grinder into the specified power source. (Check rating plate on back of unit for voltage and amperage requirements.) Do not use an extension cord.

4. Fill hopper with whole bean coffee.

5. Grind a small amount of whole bean coffee following operating instructions as described in the manual.

6. If there is any problem, consult the Troubleshooting Guide.

1. Turn the selector knob to the desired grind setting.

2. Fill the hopper with the desired type and amount of whole bean coffee. Close the lid.

3. Place the bag underneath the spout.

4. Press the start button.

5. The grinder will automatically stop when the bag is removed. On model 875, the stop button may be pressed after the grinder has completed grinding.

6. Remove bag from coffee spout once coffee is ground.

Tools required: Phillips screwdriver, Large blade screwdriver, Pliers

1. Remove all coffee from the hopper.

2. Set selector knob to the finest setting (Espresso or Turkish) depending on the model.

3. Loosen both knob retainer screws in selector knob one turn only.

4. While pressing the bag switch, located behind the spout, press the start button so that the grinder will run during adjustment.

5. With the grinder still running, turn the adjusting screw in the center of the selector knob slowly to the right until a slight chirping noise is heard. Immediately turn the adjusting screw to the left until chirping noise stops. This is the finest grind obtainable.

6. Tighten both of the knob retainer screws. Once the finest grind has been set, the other grind settings will automatically set correctly.

7. Press the stop button.

NOTICE: Always be sure the grinding burrs are not touching while the machine is running on the ESPRESSO/TURKISH setting. Otherwise serious damage to the motor may result.

This grinder is equipped with a circuit breaker to protect the motor from overloading. When the circuit breaker trips, the reset button will pop out approximately 1/4″ which stops the power to the grinder. The reset button is located on the front panel of the Model 875. To reset the circuit breaker, wait two minutes then push in the reset button. You will hear a click as it resets. If the grinder does not operate after resetting the circuit breaker, there may be an obstruction in the grinding mechanism that is stalling the motor. Turn the grind selector knob all the way to the left. Try restarting the grinder. If the circuit breaker “trips” again, the obstruction was not able to pass. In this case, the Grinder Head should be cleaned out as described in the Shear Disc Replacement section of the manual.

Cleaning Instructions

NOTICE: The person cleaning the parts should do so with clean hands.

The outside of the machine can be cleaned with warm soapy water and a damp cloth.

Grinding parts should be cleaned with a stiff brush or dry cloth. DO NOT USE WATER. See Shear Disc Replacement for instructions on assembling and disassembling grinder parts. Before reassembling, wipe motor shaft with dry cloth.

All other parts that are in contact with food must be washed with warm soapy water, rinsed, and air-dried.

Lubrication

None required.

If the motor should run and no coffee is dispensed, the Shear Disc may have sheared. Should this occur, perform the following operations in the sequence given.

Tools Required: Slotted Screwdriver, Pliers

WARNING: Unplug grinder to prevent electrical shock.

1. Remove all of the coffee beans from the hopper.

2. Remove the Grinder Cap by taking out the 2 Cap Screws.

3. Pull out the Rotary Burr and Feedworm Assembly. Clean out the Grinder Head, removing all coffee particles from inside of the Grinder Head and the Grinder Cap so that it can be reset properly.

4. Check that no obstruction has been caught on the surface of the teeth of either burr. Remove the Shear Cover and broken pieces of the Shear Disc. You are now ready to reassemble the grinder mechanism.

5. Slide the Rotory Burr and Feedworm Assembly onto the Drive Shaft. Insert the shear drive so that the Motor Shaft tongue engages into the shear drive notch.

6. Insert a new Shear Disc by aligning the slot in the Shear Drive with the slot in the hub of the Feedworm.

7. Reassemble the Shear Cover and Grinder Cap. Make certain the Grinder Cap is screwed on tight and is sealed properly against the head and not tilted or misaligned. Otherwise, a proper grind cannot be obtained.

8. Your grinder is now ready to grind.