GRINDMASTER-CECILWARE 835 (01) PDF Document

WARNING: FAILURE TO COMPLY RISKS PERSONAL INJURY, SHOCK HAZARD, FIRE, OR DAMAGE TO EQUIPMENT.

• Product must be attached to a three wire 120V 15 AMP receptacle (export units – 230V 16 AMP).

• Do not deform plug or cord.

• Follow national and local electrical codes.

• Do not use near combustibles.

• Use only on a circuit load that is properly protected and capable of the rated load.

• Always unplug unit from power supply before servicing or cleaning.

CAUTION: Personal injury hazard. Keep fingers, hands, and foreign objects out of hopper or chute opening.

Please read the manual before operating the grinder.

1. Carefully remove grinder from carton.

2. Place grinder in position on shelf, counter or other flat surface.

3. Plug grinder into the specified power source. (Check rating plate on back of unit for voltage and amperage requirements.) Do not use an extension cord.

4. Fill hopper with whole bean coffee.

5. Grind a small amount of whole bean coffee following operating instructions as described in the manual.

6. If there is any problem, consult the Troubleshooting Guide.

NOTICE: It is essential that full voltage and amperage always be available as it takes full power to grind coffee. Never connect to an overloaded circuit or to an extension cord, otherwise serious damage to the motor may result.

1. Turn the selector knob to the desired grind setting.

2. Fill the hopper with the desired type and amount of whole bean coffee. Close the lid.

3. Place the bag underneath the spout.

4. Press the start button.

5. The grinder will automatically stop when the bag is removed. On model 835, the stop button may be pressed after the grinder has completed grinding.

6. Remove bag from coffee spout once coffee is ground.

Tools required: Phillips screwdriver, Large blade screwdriver, Pliers

1. Remove all coffee from the hopper.

2. Set selector knob to the finest setting (Espresso or Turkish) depending on the model.

3. Loosen both knob retainer screws in selector knob one turn only.

4. While pressing the bag switch, located behind the spout, press the start button so that the grinder will run during adjustment.

5. With the grinder still running, turn the adjusting screw in the center of the selector knob slowly to the right until a slight chirping noise is heard. Immediately turn the adjusting screw to the left until chirping noise stops. This is the finest grind obtainable.

6. Tighten both of the knob retainer screws. Once the finest grind has been set, the other grind settings will automatically set correctly.

7. Press the stop or off button.

NOTICE: Always be sure the grinding burrs are not touching while the machine is running on the ESPRESSO/TURKISH setting. Otherwise serious damage to the motor may result.

This grinder is equipped with a circuit breaker to protect the motor from overloading. When the circuit breaker trips, the reset button will pop out approximately 1/4″ which stops the power to the grinder. The reset button is located on the front panel of the Model 835.

To reset the circuit breaker, wait two minutes then push in the reset button. You will hear a click as it resets. If the grinder does not operate after resetting the circuit breaker, there may be an obstruction in the grinding mechanism that is stalling the motor. Turn the grind selector knob all the way to the left. Try restarting the grinder. If the circuit breaker “trips” again, the obstruction was not able to pass. In this case, the Grinder Head should be cleaned out as described in the Shear Disc Replacement section.

NOTICE: The person cleaning the parts should do so with clean hands.

• The outside of the machine can be cleaned with warm soapy water and a damp cloth.

• Grinding parts should be cleaned with a stiff brush or dry cloth. DO NOT USE WATER. See Shear Disc Replacement for instructions on assembling and disassembling grinder parts. Before reassembling, wipe motor shaft with dry cloth.

• All other parts that are in contact with food must be washed with warm soapy water, rinsed, and air-dried.

If the motor should run and no coffee is dispensed, the Shear Disc may have sheared. Should this occur, perform the following operations in the sequence given.

Tools Required: Slotted Screwdriver, Pliers

WARNING: Unplug grinder to prevent electrical shock.

1. Remove all of the coffee beans from the hopper.

2. Remove the Grinder Cap by taking out the 2 Cap Screws.

3. Pull out the Rotary Burr and Feedworm Assembly. Clean out the Grinder Head, removing all coffee particles from inside of the Grinder Head and the Grinder Cap so that it can be reset properly.

4. Check that no obstruction has been caught on the surface of the teeth of either burr. Remove the Shear Cover and broken pieces of the Shear Disc. You are now ready to reassemble the grinder mechanism.

5. Slide the Rotory Burr and Feedworm Assembly onto the Drive Shaft. Insert the shear drive so that the Motor Shaft tongue engages into the shear drive notch.

6. Insert a new Shear Disc by aligning the slot in the Shear Drive with the slot in the hub of the Feedworm.

7. Reassemble the Shear Cover and Grinder Cap. Make certain the Grinder Cap is screwed on tight and is sealed properly against the head and not tilted or misaligned. Otherwise, a proper grind cannot be obtained.

8. Your grinder is now ready to grind.

Here are possible causes and solutions:

• Possible Cause: Bag not under spout.

• Solution: Place bag underneath spout.

• Possible Cause: Plug not in outlet properly.

• Solution: Install plug in outlet.

• Possible Cause: No power to outlet.

• Solution: Check outlet with lamp or radio to verify outlet has power.

Here are possible causes and solutions:

• Possible Cause: Circuit breaker has tripped.

• Solution: Reset circuit breaker by pushing in reset button until you hear a click.

• Possible Cause: Shear disc is broken.

• Solution: Replace shear disc. See Shear Disc Replacement instructions.

• Possible Cause: Obstruction in opening to grinding chamber.

• Solution: Unplug unit. Empty beans out of hopper and clear obstructions. See Shear Disc Replacement for disassembly and assembly instructions.

Here are possible causes and solutions:

• Possible Cause: Defective chaff mixer spring.

• Solution: If bent, broken, or missing, replace spring. If stuck open with coffee, clean out coffee to free spring.

• Possible Cause: Outlet not properly grounded.

• Solution: Check power cord end and outlet for proper ground.

• Possible Cause: Static electricity.

• Solution: Tighten all nuts, bolts, and screws and verify outlet is grounded.

Here are possible causes and solutions:

• Possible Cause: Insufficient amperage due to use of extension cord.

• Solution: Plug unit directly into outlet. Do not use an extension cord.

• Possible Cause: Insufficient amperage due to overloaded line.

• Solution: Designate single line for grinder. Do not use multi-outlet box.

• Possible Cause: Grind setting needs adjustment.

• Solution: Adjust grind to coarser setting (see Grind Adjustment).