GODOX VL150II (01) PDF MANUAL

This product is professional lighting equipment and should be used by professional lighting engineers or under their guidance.

Always follow basic safety attentions:

1. Read and understand all instructions and attentions before use.

2. Professional lighting is prohibited for children. Close supervision is necessary when children are near the equipment.

3. This is not an ordinary lighting product and cannot be used for general lighting. Avoid use if you have suffered eye damage or have sensitive eyes.

4. Use care when the lamp is on. Do not touch high-temperature parts like LED beads to avoid burns.

5. Do not look directly at the lamp beads when the lamp is on. Use strong light under the guidance of professional lighting engineers. Avoid prolonged exposure. If eye discomfort occurs, turn off the lamp, suspend use, and see a doctor.

6. If the lamp bead is damaged or heat-deformed, stop using the equipment and contact the manufacturer, service agent, or qualified personnel for replacement.

7. Use only in a -10°C to 40°C operating environment and normal humidity.

8. Do not use damaged equipment or accessories. Wait for professional repair and confirmation of normal function before use.

9. If the product casing breaks due to dropping, squeezing, or strong impact, do not use it to avoid electric shock from internal components.

10. If an extension cord is needed, use one with a current rating greater than or equal to the equipment’s rating to prevent overheating.

11. Place long power cords properly and safely. Avoid contact with hot surfaces, improper placement that could cause pulling damage, or tripping hazards. Use the certified power cord from the original manufacturer; damage from non-certified cords is not covered by warranty.

Ensure the equipment is unplugged from the power outlet before cleaning and repairing.

When not in use, do not pull the power cord to unplug. Hold both ends of the plug and pull it out of the power outlet.

This equipment must be connected to a grounded outlet.

No, this equipment is not waterproof. Keep it dry and do not immerse it in water or other liquids. Install it in a dry and ventilated place, avoiding use in rainy, humid, dusty, or overheated environments. Do not place objects on the lamp or allow liquid to flow into it. Take measures for waterproofing in rainy or damp environments. Always keep the product dry.

Do not disassemble the product without permission. If the product fails, it must be checked and repaired by authorized maintenance personnel. Should repairs become necessary, the product must be sent to an authorized maintenance center.

Before storing, make sure the equipment has cooled down completely. Unplug the power cord from the equipment. Store the equipment in the carrying case or in a ventilated dry place. Do not place equipment near flammable and volatile solvents like alcohol and gasoline.

When cleaning, do not wipe it with a damp cloth. Use a dry cloth or a soft cloth to wipe the dirt off the equipment.

Yes, please take off the protective cover (lamp cover) before using the light.

For products with built-in lithium batteries: Use specified chargers and operate within the specified voltage and temperature range according to instructions.

For battery-powered products:

Do not use batteries, power sources, or accessories not specified in the instructions.

Keep batteries and accessories out of reach of children and infants. Seek immediate medical attention if a battery or accessory is swallowed.

If a battery leaks, becomes discolored, deformed, emits smoke, or an abnormal odor, remove it immediately, being careful to avoid burns. Continued use could cause fire, electric shock, or burns.

Do not use deformed or modified batteries.

Do not disassemble or modify the product or battery.

Do not heat or solder the battery.

Keep the battery away from fire or water.

Do not insert batteries incorrectly (check positive/negative ends).

Do not mix old and new batteries or batteries of different types.

Compact structure, lightweight and portable

Support 2.4GHz wireless control and Bluetooth control

Strong power and stable light source, brightness adjustable from 0% to 100%

DC power supply or V-port lithium battery power supply, support both indoor and outdoor using

8 customed light effects and convenient operation

Separated adapter, controller and light body enable scientific heat dissipation

360° U-type bracket, standard Bowens mount and umbrella hole

Attached carry bag makes it conveniently portable.

Do not look directly at the light source.

The luminaire is intended for professional use only.

Keep out of reach of children.

Please take off the lamp cover before using.

Do not leave or store the product if the ambient temperature reads over 40°C.

Do not fire directly against human eyes as it may cause visual impairment.

Please use the original power cable; damages caused by using other cables will void the warranty.

As this product does not have waterproof function, please take measures for waterproof in rainy or damp environment.

Always keep this product dry. Do not use in rain or in damp conditions.

Do not use the product in the presence of flammable gases, chemicals and other similar materials.

The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.

Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.

The lamp shall be changed if it has become damaged or thermally deformed.

1. Accessory Locking Ring

2. Bowens Mount

3. LED Beads

4. Thermovent

5. Bracket Locking Ring

6. Bracket Sleeve Ring

7. Umbrella Input

8. Handle

9. Thermovent

10. Power Input Socket

11. U-type Bracket

12. Bracket Sleeve

1. Handle

2. LCD Panel

3. FX/Wireless Button

4. Adjust Dial

5. Power Switch

6. V-port Battery Slot

7. Battery Compartment

8. Battery Locking Ring

9. DC Input Port

10. DC Output Port

1. Handle

2. LCD Panel

3. FX/Wireless Button

4. Power Switch

5. Adjust Dial

6. Battery Locking Ring

7. V-port Battery Slot

8. Battery Compartment

9. DC Input Port

10. DC Output Port

VL150II Light Body\*1, Controller VLC150II\*1, Reflector \*1, Lamp cover \*1, Connect cord\*1, Adapter \*1, Power cord \*1, Back clip \*1, Instruction Manual\*1, Carry Bag CB62\*1

VL200II Light Body \*1, Controller VLC200II\*1, Reflector \*1, Lamp cover \*1, Connect cord\*1, Adapter \*1, Power cord \*1, Back clip \*1, Instruction Manual\*1, Carry Bag CB63\*1

VL300II Light Body\*1, Controller VLC300II\*1, Reflector \*1, Lamp cover \*1, Connect cord\*1, Adapter \*1, Power cord \*1, Back clip \*1, Instruction Manual\*1, Carry Bag CB64\*1

Connect the adapter and controller. Long press the Power Switch on the controller to power the LED light on or off.

Constant on mode: This is the default mode when the FX icon is not displayed on the left bottom of the panel. Turn the adjust dial to change brightness from 0% to 100%.

FX mode: Long press the FX/Wireless button to display the FX icon on the left bottom of the panel. When the FX icon flashes, turn the adjust dial to select one of the 8 light effects (see table below). Short press the FX/Wireless button to confirm the selection. When the FX icon stops flashing, turn the adjust dial to change the brightness of the effect from 0% to 100%. Short pressing the FX/Wireless button again when the FX icon is displayed (but not flashing) allows you to reselect the light effect.

Light Effects Table (8 types):

Display	FX1	FX2	FX3	FX4	FX5	FX6	FX7	FX8
Scenes	Flash 1	Flash 2	Flash	Storm 1	Storm 2	Storm 3	Broken bulb	TV

Short press the FX/Wireless button once. The CH icon will flash. Turn the adjust dial to choose a channel from 01 to 32. When the CH icon stops flashing, the setting is complete, and the controller automatically exits CH setting mode. Alternatively, while the CH icon is flashing, short pressing the FX/Wireless button 4 times will also automatically exit CH setting.

Short press the FX/Wireless button twice. The GR icon will flash. Turn the adjust dial to choose a group from A to F or 0 to 9. When the GR icon stops flashing, the setting is complete, and the controller automatically exits GR setting mode. Alternatively, while the GR icon is flashing, short pressing the FX/Wireless button 3 times will also automatically exit GR setting.

Short press the FX/Wireless button three times. The ID icon will flash. Turn the adjust dial to choose an ID from 01 to 99 or OF (Off). When the ID icon stops flashing, the setting is complete, and the controller automatically exits ID setting mode. Alternatively, while the ID icon is flashing, short pressing the FX/Wireless button twice will also automatically exit ID setting.

This function applies only to the VL300II and is used when a V-port battery enters protection mode due to not outputting sufficient power at high power settings.

To enter power option mode: While the light is powered off, press the power switch and the FX/Wireless button simultaneously. The power setting will be displayed (default is 300W).

To change the power setting: Turn the adjust dial to choose power from 200W, 250W, or 300W.

To exit: The mode will exit automatically after 5 seconds of inactivity.

Note: Selecting a lower power setting (e.g., 200W or 250W) reduces the light’s maximum output power but allows the battery to be loaded without triggering its protection mechanism.

Short press the FX/Wireless button four times. The Bluetooth icon and the MAC code will be displayed on the LCD panel, indicating you are in the Bluetooth setting interface.

First, enter the Bluetooth setting interface by short pressing the FX/Wireless button four times.

Then, long press the FX/Wireless button. The Bluetooth icon will flash, indicating that Bluetooth is resetting.

When the Bluetooth icon stops flashing, the reset is complete.

To exit: The mode will exit automatically after 10 seconds of inactivity, or you can short press the FX/Wireless button to exit immediately.

Note: A Bluetooth reset might be necessary when connecting a new mobile device (phone or tablet) to control the light via the app after a previous device was connected.

Scan the QR code provided in the manual to download the “Godox Light” mobile app (available for Android and Apple). Refer to the “Help” manual within the mobile app for specific operational details. The first mobile device can directly control the light body via the app. If switching control to a different mobile device, perform a Bluetooth reset on the light’s controller first.

If the light body reaches a high temperature, the CCT value display on the LCD panel will change to “HP”. The light body will continue to work normally at this stage.

If the light body becomes over-temperature, the light will turn off, and “HP” will flash on the LCD panel.

Once the light body cools down to a normal temperature state, the “HP” display will revert to the CCT value, and the light body will restore its lighting function.

VL150II (CCT 5600K)

Testing Conditions	Illuminance Unit	1m	2m	3m
bare lamp	lux	6100	1700	810
	fc	570	160	76.0
with reflector	lux	76000	16000	5400
	fc	7000	1500	500

VL200II (CCT 5600K)

Testing Conditions	Illuminance Unit	1m	2m	3m
bare lamp	lux	7400	2100	1100
	fc	700	190	100
with reflector	lux	88900	19000	8000
	fc	8300	1800	750

VL300II (CCT 5600K)

Testing Conditions	Illuminance Unit	1m	2m	3m
bare lamp	lux	11600	3500	1700
	fc	1100	300	160
with reflector	lux	90000	20900	8800
	fc	8400	1950	820

* All illuminance tests are based on 100% brightness.

Feature	VL150II	VL200II	VL300II
Adapter Input	AC100V-240V 50/60Hz 2A	AC100V-240V 50/60Hz 3.9A	AC100V-240V 50/60Hz 4.3A
Light Body Input	35V⎓4.3A	47.8V⎓4.2A	50V⎓6A
V-port battery	Standard voltage: 14.8V (optional)
Max. Power	165W	215W	320W
CCT Range	5600±200K
CH	32
GR	16 groups (A,B,C,D,E,F,0-9)
ID	99
CRI	≥96
TLCI	≥96
Brightness Adjustment Range	0% – 100%
Working Temperature Range	-10°C – 40°C
U-type Bracket Adjustable Angle	0°-360°
Dimensions (Light Body)	270mm\*175mm\*212mm		272mm\*176mm\*292mm
Dimensions (Controller)	114mm\*59mm\*258mm	60mm\*114mm\*426mm
Net Weight(≈) (Light Body)	1.72kg	1.77kg	2.78kg
Net Weight(≈) (Controller)	0.7kg	1.19kg	1.2kg

* Product design and specifications are subject to change without notice.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

VL150II:

Operating frequency: 2412.99MHz – 2464.49MHz (2.4G only receive) / 2402MHz – 2480MHz (BT)

Maximum EIRP Power: -0.81dBm

VL200II / VL300II:

Operating frequency: 2412.99MHz – 2464.49MHz (2.4G only receive) / 2402MHz – 2480MHz (BT)

Maximum EIRP Power: 6.83dBm

The warranty applies to the products listed on the Product Maintenance Information table. Other products or accessories (e.g., promotional items, giveaways, additional accessories attached, etc.) are not included in this warranty scope.

The warranty period for products and accessories is implemented according to the relevant Product Maintenance Information (see table below). The warranty period is calculated from the date the product is first purchased. The purchase date is considered the date registered on the warranty card when buying the product.

If maintenance service is needed, contact the product distributor or authorized service institutions directly. You can also contact the Godox after-sale service call. When applying for maintenance service, you must provide a valid warranty card. If a valid warranty card cannot be provided, maintenance service may be offered once it’s confirmed the product or accessory is within the maintenance scope, but this will not be considered an obligation under warranty.

The guarantee and service are not applicable in the following cases:

1. The product or accessory has expired its warranty period.

2. Breakage or damage caused by inappropriate usage, maintenance, or preservation (e.g., improper packing, improper usage, improper plugging in/out external equipment, falling off, external force, improper temperature, solvent, acid, base, flooding, damp environments).

3. Breakage or damage caused by non-authorized institutions or staff during installation, maintenance, alteration, addition, or detachment.

4. The original identifying information of the product or accessory is modified, alternated, or removed.

5. No valid warranty card is provided.

6. Breakage or damage caused by using illegally authorized, non-standard, or non-public released software.

7. Breakage or damage caused by force majeure or accident.

8. Breakage or damage that cannot be attributed to the product itself.

If these situations occur, seek solutions from the related responsible parties; Godox assumes no responsibility. Damage to parts, accessories, and software beyond the warranty period or scope is not covered. Normal discoloration, abrasion, and consumption are not considered breakage within the maintenance scope.

Product Maintenance Information:

Product Type	Name	Maintenance Period (month)	Warranty Service Type
Parts	Circuit Board	12	Customer sends the product to designated site
	Battery	3	Customer sends the product to designated site
	Electrical parts (e.g., battery charger, etc.)	12	Customer sends the product to designated site
Other Items	Flash tube, modeling lamp, lamp body, lamp cover, locking device, package, power cord, sync cable, etc.	No	Without warranty

Godox After-sale Service Call: 0755-29609320-8062