GODOX LED1000D II (01) PDF MANUAL

The LED1000 II video light offers the following features:

• 1024-LED-bulbs panel is lithium-ion or DC powered.

• Wirelessly adjust brightness or color temperature.

• Large-sized LCD panel. Settings auto saved.

Two models are available:

Please observe the following warnings:

• Always keep this product dry. Do not use in rain or in damp conditions.

• Do not disassemble. Should repairs become necessary, this product must be sent to an authorized maintenance center.

• Keep out of reach of children.

• As this product does not have waterproof function, please take measures of waterproof in rainy or damp environment.

• Do not use or store the product if the ambient temperature reads over 50 °C.

• Do not use the flash unit in the presence of flammable gases, chemicals and other similar materials. In certain circumstances, these materials may be sensitive to the strong light emitting from this flash unit and fire or electromagnetic interference may result.

Observe the following precautions when handling batteries:

• Do not put batteries into a fire or apply direct heat to them.

• Batteries are prone to leakage when fully discharged. To avoid damage to the product, be sure to remove batteries when the product is not used for a long time or when batteries run out of charge.

• Should liquid from the batteries come into contact with skin or clothing, rinse immediately with fresh water.

Two power supply modes are available:

• Using lithium battery: This light uses SONY BP-L model lithium battery (purchased separately).

• Using DC power jack: This light can be powered by DC power supply. Use a 13~16.8V adapter (included) to connect the light with the DC power jack (08).

Note: When using lithium battery, the Battery Level Indicator is displayed on the LCD panel. When the indicator blinks, the lithium battery power is low. Please recharge it immediately before usage in order to avoid forceful auto off.

Follow these steps to install the lithium battery:

1. Turn the Power Switch (04) off.

2. Target the socket of the lithium battery towards the “+” “-” contacts of the Battery Compartment (09). Push the battery in until it locks.

3. Power the light on.

4. After using the light, please power it off.

• Screw the Knob C (14) to the highest point and install the light stand onto the Bracket Mounting Hole (16).

• Tighten the Knob C (14).

Insert lithium battery or connect the light with DC power supply. Switch the power on, the Power Indicator is on and the video light giving out light.

• In initial state, power the LED light on to enter LED general mode.

• Long press the RUN/STOP button to switch between LED general mode and DMX mode.

• Light Brightness Adjustment: Turn the select dial on the body to adjust light brightness from 0% to 100%.

• Color Temperature Adjustment (for Bicolor version): Short press the SET button and the color temperature value will be blinking. Then, turn the select dial to adjust color temperature from 3300K to 5600K.

This product has remote grouping and control function. Up to 6 groups of LED light can be controlled. 16 channels are available with strong anti-interference capability. Please set the channels and groups of LED video light to the same as those of remote control before usage.

Adjusting Channel/Group of the LED Video Light:

• Press the CH/GR button and the group icon blinks. Turn the select dial to choose a group ID (A to F).

• Press the CH/GR button twice and the channel icon blinks. Turn the select dial to choose a channel ID (1 to 16).

Note: The wireless signal can be received only when the LED light is power on.

• Pressing the ON/OFF button on the remote control can turn on/off all the LED groups.

• Pressing the “SET” button on the remote control for 2 seconds can turn on/off the current LED group.

• The remote control will auto power off after four hours of idle operation.

Tips of Using Remote Control:

(1) When using the Daylight Version LED1000D II, please set the color temperature of the remote control as 5600K constantly.

(2) Please remove the battery if the light will not be used for an extended period of time.

• Pinch the edge of the color filter (02) and pull it out upwardly.

• Insert a new color filter in and push it downwardly. Then the color filter is securely in position.

1. Choose DMX Mode:

• In the initial state, hold down the RUN/STOP button and power the light on to enter DMX mode, and the brightness value and color temperature value will be displayed on the LCD panel.

• In LED general mode, long press the RUN/STOP button to enter DMX mode. In this way, the brightness value and color temperature value won’t be displayed on the LCD panel.

• Press the SET button and the DMX channel will be blinking. Turn the select dial to set DMX from 1 to 512.

• Choose DMX port according to the model to be controlled. Each light will occupy two DMX channels and the light brightness or color temperature can be adjusted.

Note: In DMX mode, the color temperature and light brightness can only be controlled by the console.

设计和规格如有变更,恕不另行通知。 (Product design and specifications are subject to change without notice.)

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.