GIRAFFE TOOLS TA15B (01) PDF Document

The specifications for the GIRAFFE TOOLS TA15B are as follows:

The box for the GIRAFFE TOOLS TA15B contains the following items:

1 x Retractable Hose Reel

4 x Expansion Bolt: Φ12*70

1 x Owner’s Manual

1. Check whether the parts listed in the manual are complete and in the box.

2. Check for (white) scratches on the product.

Tip: If the received package has a strange scent, know that this is caused by the sealed environment during shipment overseas.

You will need the following tools to install the GIRAFFE TOOLS TA15B:

• Electric drill (9/16″)

• Hammer

• Socket set or a Phillips screwdriver

First, choose a place for installation. Due to the weight of the filled reel and the pulling force during use, the reel must be installed on a solid surface that can withstand 20kg of force. As a matter of convenience, please install the hose reel close to your compressor outlet.

To install the reel:

1. Use the installation template to mark the location of the 4 holes.

2. Use a 9/16″ drill bit to drill 2.1 in. deep holes.

Tips: Depth is important. Mark a 2.1 in. depth with tape around the drill bit. If the hole is too deep and the wall anchor is rotating, use a matchstick or similar tool to tighten the hole.

3. Hammer the wall anchors into the 4 holes.

4. Hang the reel on the anchors, put on the washers and screw on the nuts, then use a socket set or a Phillips screwdriver to tighten.

If desired, follow steps 5 to 7 to re-position the guide arm:

5. Pull out the hose and lock it.

6. Remove the nut and washer on the guide arm base.

7. Rotate the arm to the desired position, and re-tighten the washer and nut.

Your hose reel is now installed and ready to use!

After installing your GIRAFFE TOOLS TA15B, check whether the hose retracts as intended. Look for the following issues:

– Doesn’t retract automatically

– Unable to pause

There are serial locking and non-locking areas in the steel body, and clicks can be heard when passing through the locking areas. Pull out the hose and stop when hearing the “click” sound to lock the hose.

1. To unlock the hose, give the hose a small tug until reaching the non-locking area (when not hearing the click) to start retraction.

2. To shorten the hose, start retraction and stop when hearing the click.

Tips: Hose can only be locked during the pulling out process, and cannot be locked during retraction. Always gently retract the hose. If this is not done with caution, the hose reel might get damaged. When walking backwards at a steady speed, the self-segmenting mechanism inserts the hose and weaves neatly into the reel, to ensure that it is free from kinks and tangles.

1. Always retract the hose after each use.

2. There is a “STOP” indication sticker 3.28 feet before the maximum length. Do not pull the hose past this point, otherwise, the retraction mechanism will be destroyed.

If the GIRAFFE TOOLS TA15B reel fell off the wall, check whether the reel was installed correctly.

Pull or retract the hose a little until you hear the click. Because the distance between lock points and unlock areas is very short, if you pull too quickly, you may miss the lock point.

It is possible for the hose to become jammed if it retracts unassisted. To free the hose of a jam, pull the hose firmly until it is fully extended. It should now be able to retract once again. Be sure to walk with the hose in hand at a slow speed as it retracts, until it is fully stowed.

1. Is the hose reel installed at the correct position? If the hose bends too much at the outlet, the hose may rub on the orifice, making it difficult to pull.

2. All mounting holes must be fixed to the wall.

1. Inspect the tool’s air hose for cracks, fraying or other faults before each use. Discontinue use if the air hose is damaged or hissing is heard from the air hose or connectors, while operating the tool. Replace the defective component/air hose.

2. Do not allow people, mobile equipment, or vehicles to pass over the unprotected air hose. Position the air hose away from high traffic areas, in a reinforced conduit or place planks on both sides of the air hose to create an enclosed area.

3. Prevent damage to the air hose by observing the following:

a. Never carry the tool by the air hose.

b. Keep the air hose away from heat, oil, sharp edges or moving parts.

4. Check the maximum pressure rating for air tools and accessories. Compressor outlet pressure must be regulated to never exceed the maximum pressure rating of the tool.

CAUTION! Release air pressure from the hose system before servicing the reel.

1. Maintain the tool with care. A tool in good condition is efficient, easier to control and will have fewer problems.

2. Inspect the reel, hose, and accessories for damage or excessive wear before each use.

3. Have damaged or worn components repaired or replaced by an authorized technician.

4. Only use identical replacement parts when servicing.

5. Only use accessories intended for use with this tool.

6. Maintain the tool’s labels and name plates. These carry important information. If unreadable or missing, contact us for replacements.

WARNING! Only qualified service personnel should repair the tool. An improperly repaired tool may present a hazard to the user and/or others.

Wipe the surface with a clean, moist cloth. Do not use solvents when cleaning.

1. Operate in a safe work environment. Keep your work area clean, well-lit, and free of distractions.

2. Keep anyone not wearing the appropriate safety equipment away from the work area.

3. Store unused tools properly in a safe and dry location to prevent rust or damage. Lock tools away and keep out of reach of children.

1. Always wear impact safety goggles that provide front and side protection for the eyes. Eye protection equipment should comply with CSA Z94.3-07 or ANSI Z87.1 standards, depending on the type of work that is performed.

2. Wear gloves that provide protection from the work materials or to reduce the effects of tool vibration.

3. Wear protective clothing designed for the work environment and tools.

4. Non-skid footwear is recommended to maintain balance in the work environment.

Control the tool, personal movement, and the work environment to avoid personal injury or damage to the tool.

1. Do not operate any tool when tired or under the influence of drugs, alcohol, or medications.

2. Avoid wearing clothes or jewelry that can become entangled with the moving parts of a tool. Keep long hair covered or bound.

WARNING! DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to the tool’s safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injuries.

WARNING! Direct exposure of pressurized air or fluids to skin could result in severe bodily injuries.

1. Use the correct tool for the job. This tool was designed for a specific function. Do not modify or alter this tool or use it for an unintended purpose.

2. Ensure that the reel is properly installed before connecting the input and output air hoses.

3. Remove system pressure immediately if a leak occurs in the hose or reel, or if the reel ceases to wind and unwind.

4. Release the hose slowly and control it as it retracts.