Free English GAMEMAX HYPE-M (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD GAMEMAX HYPE-M (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What components are included in the package content for the GAMEMAX HYPE-M?
The package content for the GAMEMAX HYPE-M includes:
| Image | Q’ty | Used for |
| A | 10 | Screws – MB+2.5″ SSD |
| B | 5 | Power Supply Screw |
| C | 4 | Screws -3.5″ HDD |
| D | 3 | Spare MB Stand-off |
| E | 5 | Cable Tie |
How do the connectors on the GAMEMAX HYPE-M map to the motherboard or components?
The connectors map as follows:
| Connector Pins | Description |
| PORT 1L, PORT 1R, PORT 2R, PORT 2L (with AUG GND, PRESENCE, SENSE1_R, SENSE2_R) | Combo Audio |
| USB+5V LP, LP+, GND, NC, NO PIN (on both USB-HDV side) | USB2.0 |
| VBUS, SSRX1-, SSRX1+, GND, SSTX1-, SSTX1+, GND, D1-, D1+, NC, NO PIN and VBUS, SSRX2-, SSRX2+, GND, SSTX2-, SSTX2+, GND, NC, D2-, D2+, NO PIN | USB3.0 |
| Pins labeled with a square or rectangular connection symbol | POWER SW |
| Pins labeled with a rectangular connection symbol with an arrow/line through it | RESET SW |
| Pins labeled with a circular connection symbol | LED SW |
The I/O Panel connections are:
- LED SW
- Reset SW
- Power / HDD LED
- Combo Audio
- USB2.0 (two sets)
- USB3.0
- Power SW
What are the numbered components in the Exploded View diagram for the GAMEMAX HYPE-M?
The numbered components in the Exploded View for the GAMEMAX HYPE-M are:
- Tempered glass front panel
- Tempered glass left side panel
- Right side panel
- Chassis
- HDD bracket
- Motherboard plate fan x2 (included)
- Rear fan x1 (included)
- Top fan x3 (optional)
- Bottom fan x3 (optional)
- Magnetic dust filter on top
- Magnetic dust filter at the bottom
- PWM ARGB HUB
What are the steps to remove the side panels of the GAMEMAX HYPE-M?
To remove the side panels of the GAMEMAX HYPE-M, follow these instructions:
- Remove the side panels.
What are the steps to insert and secure the PSU into the GAMEMAX HYPE-M?
To insert and secure the PSU into the GAMEMAX HYPE-M:
- Insert PSU from right side, secure with screws (B).
What are the steps for installing the motherboard in the GAMEMAX HYPE-M?
To install the motherboard in the GAMEMAX HYPE-M:
- Put in the motherboard, place the I/O baffle, and lock the screws (A).
How do you install a graphics card after removing the PCI-E slot strip in the GAMEMAX HYPE-M?
To install a graphics card in the GAMEMAX HYPE-M:
- Remove the PCI-E slot strip and install graphics card.
What is the procedure for removing the hard disk cage from the GAMEMAX HYPE-M?
To remove the hard disk cage from the GAMEMAX HYPE-M:
- Remove the hard disk cage.
How should a 2.5″ SSD be installed in the GAMEMAX HYPE-M?
To install a 2.5″ SSD in the GAMEMAX HYPE-M:
- Install 2.5″ SSD using screws (A).
What is the process for installing a 3.5″ HDD in the GAMEMAX HYPE-M?
The process for installing a 3.5″ HDD in the GAMEMAX HYPE-M is:
- Install 3.5″ HDD using screws (C).
What is the next step after installing the 3.5″ HDD in the GAMEMAX HYPE-M?
After installing the 3.5″ HDD in the GAMEMAX HYPE-M, the next step is:
- Install the hard disk cage.
What are the fan cooling system options for the top, M/B Cover, bottom, and rear of the GAMEMAX HYPE-M?
The Fan Cooling System options for the GAMEMAX HYPE-M are:
- Top: 3x120mm, 2x140mm (optional)
- M/B Cover: 2x120mm (included)
- Bottom: 3x120mm / 2x140mm (optional)
- Rear: 1x120mm (included)
What are the liquid cooling system options for the top and M/B Cover of the GAMEMAX HYPE-M?
The Liquid Cooling System options for the GAMEMAX HYPE-M are:
- Top: 120/240/360mm (optional)
- M/B Cover: 240mm (optional)
How can one control the ARGB lighting using the PWM ARGB HUB DEMO LINK GUIDE on the GAMEMAX HYPE-M?
ARGB lighting can be controlled via the PWM ARGB HUB DEMO LINK GUIDE by:
- Linking LED SW or REST Button for Manual ARGB Control.
- Connecting the SATA Power input to the HUB.
- The fans link to the respective PWM ports on the HUB.
- The CPU Cooler Fan links to the 1st PWM Port (Red) on the HUB.
- The HUB connects to the motherboard via the 5V 3pin AURA Cable and the PWM TEMP Cable links to the CPU Fan socket.
What caution should be observed when using the PWM ARGB HUB on the GAMEMAX HYPE-M?
A caution for the PWM ARGB HUB on the GAMEMAX HYPE-M is:
Please do not plug in the wrong power interface, otherwise it will burn out equipment!
CLICK HERE TO DOWNLOAD GAMEMAX HYPE-M (01) PDF DOCUMENT