ELECTROLUX ENT8MD32K (01) PDF Document

The recommended set temperatures for the ELECTROLUX ENT8MD32K are: +4°C for the fridge and -18°C for the freezer.

The temperature range for the ELECTROLUX ENT8MD32K may vary between -15 and -24°C for the freezer and between 2 and 8°C for the fridge.

The set temperature in the ELECTROLUX ENT8MD32K will be reached within 24 hours.

The ECO indicator LED light on the ELECTROLUX ENT8MD32K control panel is on when the recommended temperature or level is set.

You should switch off the Extra Freeze function on the ELECTROLUX ENT8MD32K before setting a different freezer temperature level.

When the ECO function is active on the ELECTROLUX ENT8MD32K, the set temperature of the fridge compartment is 4°C and the set temperature of the freezer compartment is -18°C.

To deactivate the ECO function on the ELECTROLUX ENT8MD32K, you can:

1. Set a different temperature. Refer to “Temperature regulation”.

2. Activate the Extra Cool and Extra Freeze functions.

To activate the Extra Cool function on the ELECTROLUX ENT8MD32K, press and hold the Fridge temperature button until the Extra Cool indicator lights up.

The Extra Cool function on the ELECTROLUX ENT8MD32K stops automatically after approximately 6 hours.

To deactivate the Extra Cool function on the ELECTROLUX ENT8MD32K before its automatic end, press and hold the Fridge temperature button until the Extra Cool indicator turns off.

To activate the Extra Freeze function on the ELECTROLUX ENT8MD32K, press and hold the Freezer temperature button until the Extra Freeze indicator lights up.

The Extra Freeze function on the ELECTROLUX ENT8MD32K stops automatically after 24 hours.

To deactivate the Extra Freeze function on the ELECTROLUX ENT8MD32K before its automatic end, press and hold the Freezer temperature button until the Extra Freeze indicator turns off.

The Door open alarm on the ELECTROLUX ENT8MD32K activates if the fridge or the freezer door is left open for approximately 5 minutes.

During the Door open alarm on the ELECTROLUX ENT8MD32K:

1. The sound is on.

2. Temperature indicators flash.

3. The alarm indicator flashes.

4. The internal fridge light may be flashing.

The sound of the Door open alarm on the ELECTROLUX ENT8MD32K can be switched off by pressing any button. The sound also switches off automatically after 1 hour.

The High temperature alarm for the freezer compartment on the ELECTROLUX ENT8MD32K activates when the freezer compartment temperature is too high. It also activates when you plug the appliance for the first time.

During the High temperature alarm for the freezer compartment on the ELECTROLUX ENT8MD32K:

1. The display shows blinking E09.

2. The alarm indicator flashes.

3. The alarm sound is on.

To turn off the High temperature alarm on the freezer compartment of the ELECTROLUX ENT8MD32K, press any button on the control panel to turn off the alarm. The alarm indicator and sound turn off. The display shows E09 for 5 seconds and then the current freezer temperature is displayed. The alarm sound turns off automatically after 1 hour.

To enable the Rest mode on the ELECTROLUX ENT8MD32K, press and hold the freezer temperature button for 5 seconds. The display shows: ō on the Freezer temperature indicator, and oF on the Fridge temperature indicator.

To switch the Rest mode on or off on the ELECTROLUX ENT8MD32K, tap the Freezer temperature button. The Freezer temperature indicator changes to ūū for the enabled or oF for the disabled Rest mode.

The Rest mode on the ELECTROLUX ENT8MD32K activates after 3 days without any interaction with the appliance. The Rest mode deactivates automatically after any interaction with the appliance.

To reposition door shelves on the ELECTROLUX ENT8MD32K:

1. Gradually pull the shelf up until it comes free.

2. Reposition as required.

To fold the shelf on the ELECTROLUX ENT8MD32K:

1. Take out the front half gently.

2. Slide it into the lower rail and under the second half.

3. Pull the drawer out while lifting it up.

Do not move the glass shelf above the vegetable drawer on the ELECTROLUX ENT8MD32K to ensure correct air circulation.

To remove the GreenZone drawer from the ELECTROLUX ENT8MD32K:

1. Empty the drawer.

2. Pull out the drawer from the fridge.

3. Lift up the front of the drawer.

4. Pull the drawer out while lifting it up.

To remove the ExtraChill drawer from the ELECTROLUX ENT8MD32K:

1. Pull out the drawer from the refrigerator.

2. Lift up the front of the drawer.

3. Lift up and turn the drawer to pull it out of the appliance.

If condensation may occur in the GreenZone drawer of the ELECTROLUX ENT8MD32K, remove it using a soft cloth.

The Humidity control device on the glass shelf of the GreenZone drawer on the ELECTROLUX ENT8MD32K provides for optimal humidity inside the drawer. Do not place any food products on the humidity control device.

To remove the humidity control device from the GreenZone drawer of the ELECTROLUX ENT8MD32K:

1. Open the drawer below the glass shelf and pull out the cover.

2. To replace the device’s white membrane, grab the device in the middle and separate the membrane from the cover by pulling the cover.

3. Assemble a new membrane into the cover by pressing the edge of the membrane into the cover.

4. Reassemble the humidity control back on the drawer.

The Cooling360° fan in the fridge compartment of the ELECTROLUX ENT8MD32K allows for rapid and effective cooling of food, and keeps uniform temperature in the compartment. The fan activates automatically and operates only when the door is closed. Do not remove the Cooling360° panel.

Before putting products in the freezer compartment of the ELECTROLUX ENT8MD32K for the first time or after a period out of use, let the appliance run at least 3 hours with the Extra Freeze function switched on.

To ensure good air circulation when storing food on the shelves in the freezer compartment of the ELECTROLUX ENT8MD32K, keep the food on the shelves no closer than 15 mm from the door.

Deep-frozen or frozen food, prior to being used, can be thawed in the refrigerator compartment or at room temperature, depending on the time available for this operation using the ELECTROLUX ENT8MD32K.

The shelf life for bread stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 3 months.

The shelf life for vegetables stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 8-10 months.

The shelf life for butter stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 6-9 months.

The shelf life for hard cheese (e.g. parmesan, cheddar) stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 6 months.

The shelf life for fatty fish (e.g. salmon, mackerel) stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 2-3 months.

The shelf life for shrimps stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 12 months.

The shelf life for poultry stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 9-12 months.

The shelf life for beef stored in the freezer compartment of the ELECTROLUX ENT8MD32K is 6-12 months.

A good temperature setting that ensures preservation of fresh food in the ELECTROLUX ENT8MD32K refrigerator compartment is a temperature less than or equal to +4°C.

If food has defrosted even partially in the ELECTROLUX ENT8MD32K, do not re-freeze it. Consume it as soon as possible.

Before using the ELECTROLUX ENT8MD32K for the first time, the interior and all internal accessories should be washed with lukewarm water and some neutral detergent to remove the typical smell of a brand-new product, then dried thoroughly.

Do not use detergents, abrasive powders, chlorine or oil-based cleaners as they will damage the finish of the ELECTROLUX ENT8MD32K.

Clean the control panel of the ELECTROLUX ENT8MD32K with a moist cloth. Do not use any detergents. After cleaning, wipe the control panel dry with a soft cloth.

To clean the interior and accessories of the ELECTROLUX ENT8MD32K regularly:

1. Clean the inside and accessories with lukewarm water and some neutral detergent.

2. Regularly check the door seals and wipe them clean to ensure they are clean and free from debris.

3. Rinse and dry thoroughly.

The freezer compartment of the ELECTROLUX ENT8MD32K is frost free; there is no build up frost on the internal walls nor on the foods when the appliance is in operation.

Defrosting of the fridge compartment on the ELECTROLUX ENT8MD32K is automatic. The water that condenses flows into a recipient on the compressor and evaporates. The recipient cannot be removed.

When the ELECTROLUX ENT8MD32K is not in use for long periods, take the following precautions:

1. Disconnect the appliance from electricity supply.

2. Remove all food.

3. Clean the appliance and all accessories.

4. Leave the doors open to prevent unpleasant smells.

The possible causes if the ELECTROLUX ENT8MD32K appliance does not operate are:

1. The appliance is switched off.

2. The mains plug is not connected to the mains socket correctly.

3. There is no voltage in the mains socket.

The solutions if the ELECTROLUX ENT8MD32K appliance does not operate are:

1. Switch on the appliance.

2. Connect the mains plug to the mains socket correctly.

3. Connect a different electrical appliance to the mains socket. Contact a qualified electrician.

The possible cause if the ELECTROLUX ENT8MD32K appliance is noisy is that the appliance is not supported properly.

The solution if the ELECTROLUX ENT8MD32K appliance is noisy is to check if the appliance stands stable.

The possible causes if the acoustic or visual alarm is on for the ELECTROLUX ENT8MD32K are:

1. The cabinet has been recently switched on.

2. The temperature in the appliance is too high.

3. The door is left open.

The solutions if the acoustic or visual alarm is on for the ELECTROLUX ENT8MD32K are:

1. Refer to “High temperature alarm”.

2. Close the door.

The possible causes if the compressor of the ELECTROLUX ENT8MD32K operates continually are:

1. Temperature is set incorrectly.

2. Too much food is put in at the same time.

3. The room temperature is too high.

4. Food placed in the appliance is too warm.

5. The door is not closed correctly.

6. The Extra Freeze function is switched on.

7. The Extra Cool function is switched on.

The solutions if the compressor of the ELECTROLUX ENT8MD32K operates continually are:

1. Refer to “Control panel” chapter.

2. Wait a few hours and then check the temperature again.

3. Refer to “Installation” chapter.

4. Allow food to cool to room temperature before storing.

5. Refer to “Closing the door” section.

6. Refer to “Extra Freeze function” section.

7. Refer to “Extra Cool function” section.

The possible cause if the compressor of the ELECTROLUX ENT8MD32K does not start immediately after pressing the “Extra Freeze” or “Extra Cool”, or after changing the temperature is that the compressor starts after a period of time.

The solution if the compressor of the ELECTROLUX ENT8MD32K does not start immediately after pressing the “Extra Freeze” or “Extra Cool”, or after changing the temperature is that this is normal, no error has occurred.

The possible cause if the door of the ELECTROLUX ENT8MD32K is misaligned or interferes with the ventilation grill is that the appliance is not levelled.

The solution if the door of the ELECTROLUX ENT8MD32K is misaligned or interferes with the ventilation grill is to refer to installation instructions.

The possible cause if the door of the ELECTROLUX ENT8MD32K does not open easily is that you attempted to re-open the door immediately after closing.

The solution if the door of the ELECTROLUX ENT8MD32K does not open easily is to wait a few seconds between closing and re-opening of the door.

The possible causes if the lamp does not work on the ELECTROLUX ENT8MD32K are:

1. The lamp is in stand-by mode.

2. The lamp is defective.

The solutions if the lamp does not work on the ELECTROLUX ENT8MD32K are:

1. Close and open the door.

2. Contact the Authorized Service Centre.

The possible causes if there is too much frost and ice in the ELECTROLUX ENT8MD32K are:

1. The door is not closed correctly.

2. The gasket is deformed or dirty.

3. Food is not wrapped properly.

4. Temperature is set incorrectly.

5. Appliance is fully loaded and is set to the lowest temperature.

6. Temperature set in the appliance is too low and the ambient temperature is too high.

The solutions if there is too much frost and ice in the ELECTROLUX ENT8MD32K are:

1. Refer to “Closing the door” section.

2. Refer to “Closing the door” section.

3. Wrap the food properly.

4. Refer to “Control panel” chapter.

5. Set a higher temperature. Refer to “Control panel” chapter.

6. Set a higher temperature. Refer to “Control panel” chapter.

The possible cause if water flows on the rear plate of the refrigerator of the ELECTROLUX ENT8MD32K is during the automatic defrosting process, frost melts on the rear plate.

The solution if water flows on the rear plate of the refrigerator of the ELECTROLUX ENT8MD32K is that this is correct.

The possible causes if there is too much condensed water on the rear wall of the fridge of the ELECTROLUX ENT8MD32K are:

1. Door was opened too frequently.

2. Door was not closed completely.

3. Stored food was not wrapped.

The solutions if there is too much condensed water on the rear wall of the fridge of the ELECTROLUX ENT8MD32K are:

1. Open the door only when necessary.

2. Make sure the door is closed completely.

3. Wrap food in suitable packaging before storing it in the appliance.

The possible cause if there are water drops on the glass shelves of the ELECTROLUX ENT8MD32K is there is too much moisture inside the fridge.

The solution if there are water drops on the glass shelves of the ELECTROLUX ENT8MD32K is to wipe the glass shelves with a cloth to remove water drops.

The possible causes if the temperature cannot be set on the ELECTROLUX ENT8MD32K are:

1. The Extra Freeze function or Extra Cool function is switched on.

2. The temperature in the appliance is too low/too high.

3. The door is not closed correctly.

4. The food is too hot.

The solutions if the temperature cannot be set on the ELECTROLUX ENT8MD32K are:

1. Switch off Extra Freeze function or Extra Cool function manually, or wait until it deactivates automatically. Refer to “Extra Freeze function” or “Extra Cool function” section.

2. Set a higher/lower temperature.

3. Refer to the “Closing the door” section.

4. Let the food cool down before storage.

The possible cause if too much food is stored at the same time in the ELECTROLUX ENT8MD32K is that the door has been opened often, or The Extra Freeze function is switched on, or The Extra Cool function is switched on, or There is no cold air circulation in the appliance.

The solutions if too much food is stored at the same time in the ELECTROLUX ENT8MD32K are:

1. Store less food at the same time.

2. Open the door only if necessary.

3. Refer to the “Extra Freeze function” section.

4. Refer to the “Extra Cool function” section.

5. Ensure cold air circulation in the appliance. Refer to the “Hints and tips” chapter.

If the display of the ELECTROLUX ENT8MD32K alternates between warning codes E 01 – E 05 and temperature value, the possible cause is a Temperature sensor problem. Contact the Authorised Service Centre. The cooling system will continue to keep food cold, but temperature adjustment will not be possible. If the problem persists, contact the Authorised Service Centre.

For replacing the lamp on the ELECTROLUX ENT8MD32K, contact the Authorized Service Centre.

To ensure the door gaskets are clean on the ELECTROLUX ENT8MD32K:

1. Clean the door gaskets.

2. If necessary, adjust the door. Refer to the “Installation” chapter.

3. If necessary, replace the defective door gaskets. To obtain more information, contact the Authorised Service Centre.