Free English GAMEMAX AUTOBOT II (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD GAMEMAX AUTOBOT II (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I remove the panels on the GAMEMAX AUTOBOT II?
To remove the panels on the GAMEMAX AUTOBOT II, follow these steps:
1. Unscrew side-panel thumb-screws.
2. Slide side-panels back to release.
What is included in the accessory pack for the GAMEMAX AUTOBOT II?
The accessory pack contents for the GAMEMAX AUTOBOT II are as follows:
| Part Name | Quantity |
|---|---|
| Motherboard Screw / +2.5″ Drive Screw | x18 |
| Power Supply Screw | x5 |
| 3.5″ Drive Screw | x8 |
| Motherboard Stand-off | x4 |
| Velcro Cable Tie | x6 |
| Remote Controller | x1 |
How do I install the motherboard in the GAMEMAX AUTOBOT II?
Follow these steps to install the motherboard into the GAMEMAX AUTOBOT II:
1. Find the correct stand-off locations by aligning with your motherboard and fasten needed stand-offs accordingly.
2. Insert your motherboard I/O back-plate into the cut-out.
3. Place your motherboard into the chassis with the ports inserted into the I/O back-plate.
4. Secure the motherboard with the motherboard screws included.
How do I install a GPU card in the GAMEMAX AUTOBOT II?
To install a GPU card in the GAMEMAX AUTOBOT II:
1. Unscrew and remove the add-on card cover until it comes free.
2. Insert the PCI/PCI-E card into position and secure with screw/s.
How do I install the power supply in the GAMEMAX AUTOBOT II?
To install the power supply unit (PSU):
1. Place PSU on the bottom of the case.
2. Align holes and secure with screws.
How do I install 3.5″ HDDs and 2.5″ SSDs in the GAMEMAX AUTOBOT II?
For 2.5″ SSD Installation: Place your 2.5″ drive in and secure with screws.
For 3.5″ HDD Installation: Place your 3.5″ drive in and secure with screws.
How do I install the top, front, and rear fans in the GAMEMAX AUTOBOT II?
To install the fans in the Top, Front, or Rear positions:
1. Align and secure your 120mm fan with screws.
Note: The Top supports 120mm x2 (Optional), the Front supports 120mm x3 (Optional), and the Rear supports 120mm x2 (Included).
How do I install liquid cooling in the GAMEMAX AUTOBOT II?
1. Secure the fans on the radiator.
2. Fasten the radiator inside of the casing by screwing it from outside.
Note: The Top supports 240mm radiators and the Rear supports 120mm radiators.
How do I connect the V4.0 PWM ARGB HUB in the GAMEMAX AUTOBOT II?
Follow the connection guide below for the V4.0 PWM ARGB HUB:
1. Connect the SATA Power input.
2. Link LED SW or REST Button for Manual ARGB Control.
3. Connect the 5V 3pin AURA Cable (ARGB) or VDG (for GIGABYTE MB only). Note: Can’t link both together!
4. Connect the PWM TEMP Cable to the CPU Fan socket.
5. Connect the CPU Cooler Fan to the 1st PWM Port (Red).
Warning: Please do not plug in the wrong power interface, otherwise it will burn out equipment!
What are the functions of the remote controller for the GAMEMAX AUTOBOT II?
The remote controller features the following functions:
Power: ON/MB SYNC, Power off.
Modes: Automatic Mode Cycle, Mode +, Mode -.
Fan Control: Fan Speed + (Static Brightness +), Fan Speed – (Static Brightness -).
Color: Static Color Button.
Pairing: PassCode/PairCode (Double click 10 times).
RGB Adjustment: RGB sequence adjustment (Double click 10 times).
How do I pair or adjust the RGB sequence with the remote controller for the GAMEMAX AUTOBOT II?
PassCode/PairCode: Double click 10 times. A quick flash 3 times indicates PairCode; a slow flash 3 times indicates PassCode.
RGB Sequence Adjustment: Double click 10 times. Press the red key until the red light appears. Press the green key until the green light appears. Press OFF key to save.
CLICK HERE TO DOWNLOAD GAMEMAX AUTOBOT II (01) PDF DOCUMENT