ELDOM TOLL WG100 (01) PDF DOCUMENT

Before first use, please thoroughly read the entire manual. It is recommended to keep this instructions manual for future reference.

1. The cord should be plugged into a power supply with parameters indicated on the data plate.

2. Please do not plug too many appliances into a single electric circuit.

3. WARNING: do not use the ELDOM TOLL WG100 close to bathtubs, showers, swimming pools, and other water containers.

4. The unit is designed for household use only.

5. Place the unit on a flat and dry surface.

6. Do not insert fingers or any other objects into the inlet and outlet holes.

7. Do not place the unit near cushions or curtains.

8. The working fan must always be supervised, especially when children are nearby.

9. When leaving a room where the fan is operating, switch it off.

10. Do not spray any insect killers or similar agents near the operating fan.

11. Do not use the appliance under high temperature (exceeding 40°C), in locations where the humidity rate is high (e.g., bathroom), and in locations where an explosive atmosphere occurs.

12. Before switching the unit on, make sure all its elements are correctly fixed. Under no circumstances should one switch the unit on before it has been completely assembled.

13. Do not cover the protective mesh.

14. Do not use the appliance as a hanger.

15. In case the power cord is damaged, it must be replaced by the manufacturer’s authorized service center.

16. The device can be used by children aged 8 and older and by persons with limited physical, sensory, or mental capabilities, or persons without sufficient experience and knowledge only under supervision or if previously instructed on the safe use of the appliance and the possible risks. Children shall not play with the appliance. Cleaning and maintenance that are the responsibility of the user shall not be carried out by children without supervision. Protect the appliance and the power cord against children under 8 years old.

17. The device can be repaired only by an authorized service center. Any upgrades or any use of non-original spare parts or equipment components is prohibited and endangers the safety of use.

WARNING: Improper use of the appliance may cause injury.

WARNING: The plastic bag can be dangerous. To avoid the danger of suffocation, keep this bag away from babies and children.

The ELDOM TOLL WG100 stand fan consists of the following parts:

1. Bracket

2. Protective net – front

3. Propeller locking nut

4. Propeller

5. Safety nut net

6. Protective net – rear

7. Mandrel

8. Motor housing

9. Body

10. Control panel

11. Cable

12. Lock

13. Extension tube

14. Height adjustment ring

15. Base tube

16. Base

17. Remote control

The technical specifications are:

Power: 45W

Supply Voltage: 220-240V~ 50/60Hz

Before first use, check that the unit is complete and undamaged. Unpack the appliance and assemble the individual components by following these steps:

1. Connect the base tube (15) to the base (16).

2. Slide out the extension tube (13) and lock it with the height adjustment ring (14).

3. Connect the body (9) to the extension tube (13) and lock it by tightening the lock (14).

4. Slide the rear mesh (6) onto the stem (7).

5. Align the holes of the rear net (6) with the hooks on the motor housing (8) and fix it with the nut (5).

6. Slide the propeller (4) onto the stem (7) and fix it with the nut (3).

7. Loosen the bolt in the bracket (1), then put the bracket (1) on the mounted rear net (6).

8. Fit the front net (2) into the bracket (1) and secure by tightening the screw in the bracket (1) as far as it will go.

9. Place the assembled unit on a stable and level surface.

10. Adjust the height by loosening the ring (14), sliding the tube (13) in or out to the required height, and then locking it by tightening the ring (14).

11. Adjust the angle of the fan head (canopy).

12. Unwind the cable completely before use.

All setting changes on the ELDOM TOLL WG100 are confirmed with a beep. You can switch off all functions of the device at once by pressing the OFF button.

1. Connect the device to the mains according to the parameters given in the technical data.

2. Switch on the appliance using the “SPEED/ON” button. By pressing it repeatedly, you can set the speed. The indicator light (L, M, or H) will light up to show the current speed.

3. Use the buttons on the control panel or the remote control to select other functions.

4. To switch the fan off, press the “OFF” button.

The control panel (10) features the following controls:

SPEED/ON: Turns the fan on and controls the speed.

OFF: Switches the device off.

TIMER: Switches the automatic shut-off function on or off.

MODE: Selects pre-programmed operation modes.

L, M, H: Indicator lights for fan speed control (low, medium, high).

NAT, NOR, SLP: Indicator lights for operating modes (natural, normal, night).

4H, 2H, 1H, 0.5H: Indicator lights for the automatic shut-off time setting.

The remote control (17) has the following buttons:

LAMP: Turns the control panel indicator lights on or off.

SWING: Turns the oscillation function on or off.

TIME: Turns the automatic switch-off timer on or off.

SPEED/ON: Turns the fan on or off and controls the operating speed.

MODE: Selects from the pre-programmed operation modes.

OFF: Switches the device off.

The ELDOM TOLL WG100 has three operating modes:

NAT – Natural Mode:

1. Press the “SPEED/ON” button to switch on the fan.

2. Press the “MODE” button until the “NAT” light comes on.

3. In this mode, the fan will cycle through speeds from highest to lowest to simulate a natural breeze.

NOR – Normal Mode:

1. Use the “SPEED/ON” button to switch on the fan and select the operating speed (Low, Medium, or High).

2. Press the “MODE” button until the “NOR” light comes on.

3. The fan will run continuously at the selected speed.

SLP – Night Mode:

1. Press the “SPEED/ON” button to switch on the fan and select the operating speed.

2. Press the “MODE” button until the “SLP” light comes on.

3. In this mode, the fan will cycle on and off while operating at the selected speed, providing a gentle, intermittent airflow suitable for sleeping.

The oscillation function can only be activated using the remote control.

1. Use the “SPEED/ON” button to switch on the fan and select the desired operating speed.

2. Press the “SWING” button on the remote control. The fan will begin to oscillate (turn from side to side).

3. To deactivate the function, press the “SWING” button on the remote control again.

The timer function allows you to set a time after which the unit will automatically switch off. This function can only be activated when the fan is already on.

1. Turn the fan on and select your desired speed using the “SPEED/ON” button.

2. Press the “TIME” button on the remote control or the control panel. Each press adds 30 minutes to the timer, up to a maximum of 7.5 hours. The corresponding indicator lights on the control panel will illuminate to show the total time set.

Number of presses and corresponding time:

1 time: 0.5 hours (“0.5H” light on)

2 times: 1 hour (“1H” light on)

3 times: 1.5 hours (“1H” and “0.5H” lights on)

4 times: 2 hours (“2H” light on)

5 times: 2.5 hours (“2H” and “0.5H” lights on)

6 times: 3 hours (“1H” and “2H” lights on)

7 times: 3.5 hours (“1H”, “2H”, and “0.5H” lights on)

8 times: 4 hours (“4H” light on)

9 times: 4.5 hours (“4H” and “0.5H” lights on)

10 times: 5 hours (“4H” and “1H” lights on)

11 times: 5.5 hours (“4H”, “1H”, and “0.5H” lights on)

12 times: 6 hours (“4H” and “2H” lights on)

13 times: 6.5 hours (“4H”, “2H”, and “0.5H” lights on)

14 times: 7 hours (“4H”, “2H”, and “1H” lights on)

15 times: 7.5 hours (“4H”, “2H”, “1H”, and “0.5H” lights on)

The fan will continue to run at the selected speed and will switch off automatically after the set time has passed.

Follow these steps to clean your fan:

1. Unplug the appliance from the mains and wait for the propeller to stop completely before cleaning.

2. The appliance must not be submerged in water.

3. Wipe the main unit with a damp cloth and then wipe it dry.

4. To clean the blades and guards, remove the front net, propeller, and rear net. Wipe these components with a damp cloth and then wipe them dry.

5. Do not use strong or surface-damaging cleaners. Do not use any aggressive cleaning agents.

The symbol on the product or its packaging indicates that it should not be classified as household waste. It should be handed over to an appropriate company dealing with the collection and recycling of electrical and electronic equipment. The correct disposal of the product will prevent potential negative consequences for the environment and human health resulting from hazardous substances present in the product.

Electrical devices must be handed over to restrict their re-use and further treatment. If the device contains batteries, remove them and hand them over to a separate storage point. DO NOT THROW THE EQUIPMENT INTO THE MUNICIPAL WASTE BIN. Material recycling helps to preserve natural resources. For detailed information on how to recycle this product, please contact your local authority, the recycling company, or the shop where you bought it.