ARGO THOR PLUS (01) PDF DOCUMENT

The ARGO THOR PLUS air conditioner uses the special refrigerant R290, which is a fluoride with a Global Warming Potential (GWP) of 3. This refrigerant is flammable and inodorous. While its flammability is very low and it can only be ignited by fire, it can lead to explosions under certain conditions.

Warning:

• Do not try to accelerate the defrosting process or clean the appliance in ways other than those recommended by the manufacturer.

• If repairs are needed, contact your nearest authorized Service Centre. Repairs by unqualified personnel may be dangerous.

• The appliance must be stored in a room without continuously operating ignition sources (e.g., open flames, an operating gas appliance, or an operating electric heater).

• Do not pierce or burn the appliance.

• The ARGO THOR PLUS must be installed, used, and stored in a room with a floor area larger than 12 m².

• Be aware that refrigerants like R290 may have no smell.

Please observe the following safety instructions when using your ARGO THOR PLUS portable air conditioner:

• This appliance is a local air conditioner designed for domestic use only. Use it only as described in the manual.

• Ensure the required voltage and frequency (220-240V~/50 Hz) match your power source.

• Use a fuse style 5ET or SMT 250V. The electricity passing through the fuse cannot exceed 3.15A.

• This appliance can be used by children aged 8 years and above and individuals with reduced physical, sensory, or mental capabilities if they have been given proper supervision or instruction.

• Children shall not play with the appliance. Cleaning and user maintenance should not be done by children without supervision.

• Ensure your electricity system can handle the operating current required by the ARGO THOR PLUS, in addition to other appliances.

• The system socket must always have an efficient earth connection.

• Ensure the plug is fully inserted. Do not use multiple adapters. Do not touch the plug with wet hands. Make sure the plug is clean.

• Do not use the plug to start/stop the unit; use the ON/OFF button on the remote or control panel.

• Do not install the unit in rooms where it may receive water splashes, such as laundry rooms.

• Before moving or cleaning the device, ensure that it is unplugged from the socket.

• Do not move the ARGO THOR PLUS while it is operating. First, turn the appliance off, check for any condensate build-up, and empty it if necessary.

• To turn the appliance off completely, set the remote control to OFF and then remove the plug from the socket. Pull on the plug only; do not pull the cord.

• Do not leave the unit unattended while it’s operating; turn the unit off and unplug it.

• Do not insert any objects into the air conditioner, as the fan turns at high speed and this is very dangerous.

• Ensure that air circulates freely around the unit. Do not cover the air intake and delivery grilles with drapes or any other means.

• The appliance must be positioned at least 50 cm from any wall or obstacle, on a flat and stable surface to avoid water leaks.

• Keep the unit away from fire, possible fire sources, and inflammable or explosive objects.

• If a drainage hose is used, the ambient temperature must not be lower than 0 °C to prevent water leakage.

• Do not splash or pour water on the air conditioner.

The ARGO THOR PLUS is equipped with a system to protect the compressor from overload. This means that the compressor will only start 3 minutes after its previous stoppage. Please wait at least 3 minutes before starting the unit to help prevent the compressor from being damaged.

In the event of an anomaly or malfunction, switch the appliance off and unplug it from the socket immediately. Do not dismantle or attempt to repair or modify the unit. Contact the service centre directly.

To maximize air conditioning efficiency, close all open windows. Also, avoid exposing the unit to direct sunlight, as this can cause the appliance to overheat and switch off. Do not use insecticides, oils, detergents, or spray paints near the appliance, as aggressive chemicals may damage the finish and colour.

The ARGO THOR PLUS consists of the following parts:

1. Air outlet

2. Front panel

3. Control panel

4. Handle

5. Hole for condensate drainage (in dehumidification mode)

6. Air outlet hose

7. Plug socket

8. Upper air filter

9. Upper air inlet

10. Lower air filter (not removable)

11. Lower air inlet

12. Power cord buckle

13. Hole for condensate drainage (in cooling mode)

The operating limits (internal temperature) for the ARGO THOR PLUS are:

• Cooling: 16 °C B.S. / 35 °C B.S.

• Dehumidification: 16 °C B.S. / 35 °C B.S.

• Heating: 5 °C B.S. / 35 °C B.S.

The cooling mode room temperature adjustment range is from 16 °C B.S. to 32 °C B.S.

To ensure the operating efficiency of the ARGO THOR PLUS portable air conditioner, you must maintain a minimum space of 50 cm on the sides and back of the unit.

The following elements are supplied with your ARGO THOR PLUS:

• Remote controller

• Battery for remote controller (type AAA – LR03 – 1.5 V)

• Fitting to apply on the unit for the exhaust pipe

• Hose of expulsion of the air

• Terminal flat fitting to be placed between window knockers

• Condensate drainage pipe

• Circular fitting for kit porthole

• Porthole kit with cap

1. Stretch the flexible hose so that it reaches the outside (max 1.5 m) and hook it to the rear part of the air conditioner.

2. Open the window and lock one of the two leaves with the handle. Rest the terminal connection on the fixed leaf, and bring the other leaf of the window close to it.

1. To make a hole in the glass, it is advisable to take the porthole kit accessory to a glazier.

2. Insert the porthole into the window.

3. Insert the circular connector into the retractable hose, and then insert the hose with the connector into the porthole (without the cap).

4. When not in use, disconnect the hose and close the porthole with the cap.

Avoid tight bends or folds in the hose. The hose, once fully extended, must be placed at a higher height than the tube attachment on the machine, approximately between 40 and 160 cm, to ensure the performance of the air conditioner is not compromised. If the air conditioner is not used for prolonged periods, disconnect the pipe and plug the window unit.

Before using the appliance, leave it in an upright position for at least two hours. Plug the power cord into an appropriate power outlet (220-240V~). Insert the supplied battery into the remote controller, observing the polarities.

• Press the MODE button to select the cooling mode. The cool LED on the control panel will turn on.

• The temperature can be adjusted between 16 °C and 32 °C.

• In this mode, each time the ON/OFF button is pressed, the unit switches off and saves the temperature setting for when it is switched on again.

• The fan speed can be adjusted, and the Timer and SLEEP functions can be set.

• For more silent operation, run the fan at low speed.

• Press the MODE button to select the heating mode. The heat LED on the control panel will turn on.

• The temperature can be adjusted between 16 °C and 32 °C.

• In this mode, the fan speed can be adjusted.

• Press the MODE button to select the dehumidification mode. The dry LED on the control panel will turn on.

• The temperature is controlled by the electronic board and cannot be adjusted.

• In this mode, each time the ON/OFF button is pressed, the unit switches off and saves the settings for when it is switched on again.

• The fan speed is set to low and cannot be adjusted.

Note: The air conditioner does not cool the room when operating as a dehumidifier. The flexible pipe must not be connected. For maximum efficiency, leave the rear discharge attachment free to discharge directly into the environment. Continuous drainage is advisable in this mode.

FAN MODE:

• Press the MODE button to select Fan mode. The fan LED on the control panel will turn on.

• In this mode, the fan speed can be adjusted.

• The temperature cannot be adjusted.

AUTO MODE:

• Press the MODE button to select Auto mode. The AUTO LED on the control panel will light up.

• This mode allows the appliance to automatically select the operating mode (Cooling or Ventilation) based on the temperature in the room.

Cooling Mode: The appliance automatically vaporizes the condensation. Continuous drainage is not necessary, except in very high humidity conditions. Make sure the rubber caps on the back drain holes are correctly positioned. If the internal tank becomes full, the display shows “P1” and operation stops. To empty, turn off and unplug the unit, remove the cap from the rear drain hole, connect the supplied drain tube, and place the other end above a drain.

Heating Mode: The condensate is not vaporized automatically. The internal tank will need to be emptied periodically as described above. Alternatively, continuous drainage can be set up from the lower hole on the back of the unit.

Dehumidification Mode: When using the ARGO THOR PLUS in dehumidification mode, it is advisable to always set up continuous drainage for maximum efficiency. Connect one end of the provided PVC tubing to the top drain hole and the other end above a drain.

1. Remove the cover by unscrewing the screw with a screwdriver.

2. Open the battery compartment by sliding the door outwards.

3. Insert two new AAA batteries, paying attention to the “+” and “-” polarity.

4. Replace the cover in the battery compartment.

5. Close the door by inserting the screw with a screwdriver.

• Do not expose batteries to heat sources like fire or sun.

• Remove batteries if they heat up or if you will not use the appliance for a long time.

• In case of a battery fluid leak, remove all batteries. If the fluid contacts your skin or clothes, wash with water immediately.

• Clean the battery compartment thoroughly before inserting new batteries.

• Caution: There is a danger of explosion if the battery is replaced by an incorrect type. Only use batteries of the same size and type.

• Keep batteries out of reach of children.

• Do not heat, open, puncture, cut, or throw batteries into fire.

• Do not mix old and new batteries or batteries of different types.

• Do not leave metal objects that could contact the battery terminals.

1. WIFI button: Press to turn on/off Wi-Fi operation.

2. ON/OFF button: Press to turn the unit on or off. It will start with the last used settings (Memory function).

3. FILTER RESET button: An LED indicator comes on every 250 hours of use to signal the filter needs cleaning. After cleaning, press this button to reset the hour count.

4. FAN SPEED button: Press to adjust the fan speed in a circular sequence: AUTO -> High -> Med -> Low.

5. UP/DOWN (+/-) buttons: Adjust the temperature (1 °C steps) or set the timer (0.5 hour steps).

6. MODE button: Select the operating mode in a circular sequence: Heating -> Auto -> Cooling -> Dehumidification -> Ventilation.

7. SLEEP button: Activates or deactivates sleep mode.

8. SWING button: Activates or deactivates the automatic swing of the horizontal air louvers.

In operating mode, press “SLEEP” to enter 10 hours of intelligent sleep mode. After 10 hours, the air conditioner will exit Sleep mode and restore the previous mode. To exit early, press “SLEEP” again, or press “MODE” or “ON/OFF”.

Note: Sleep function is not available in ventilation mode. In cooling mode, after the first hour, the set temperature increases by 1 °C, and after the second hour it increases again by 1 °C. After the 5th hour, it decreases by 1 °C and continues this pattern for another 3 hours before exiting sleep mode.

• To set a turn-on time: When the unit is off, press “TIMER”. The ON icon will flash. Use “+” or “-” to set the time (in 0.5-hour increments, up to 24 hours). Press “TIMER” again to confirm. The ON icon will stop flashing.

• To set a turn-off time: When the unit is on, press “TIMER”. The OFF icon will flash. Use “+” or “-” to set the time. Press “TIMER” again to confirm. The OFF icon will stop flashing.

• To cancel the timer: Press the “TIMER” button. The Timer LED on the control panel will turn off.

To activate or deactivate the child lock, press the HEAT and MODE buttons on the remote control at the same time for 3 seconds. This will lock the buttons on the air conditioner’s control panel. When activated, a lock icon is visible on the remote control display.

If an error occurs on your ARGO THOR PLUS, do not attempt to repair it yourself (except for P1). Contact an assistance centre. The error codes are as follows:

1. For your mobile device (smartphone or tablet), search for and download the “SmartLife” app from Google Play or the App Store and install it.

2. Follow the instructions on the app step by step to register and log in.

3. Reset the Wi-Fi module on the air conditioner (see below).

4. Once logged into the Smart Life app, you can add the ARGO THOR PLUS by scanning the QR code located on the side of the unit.

There are two ways to reset the Wi-Fi module:

• Using the remote control: With the unit turned on, press the COOL and + buttons simultaneously for 3 seconds. When you hear 8 “beep beeps”, do not release the buttons. After hearing two more “beep beeps”, release the buttons.

• Using the control panel: Long press the Wifi button on the control panel and release it when you hear 8 “beep beeps”.

Before any cleaning, unplug the appliance. The air filter should be checked at least once every two weeks.

1. To remove the filter, unhook the rear grille and then gently pull the filter upwards.

2. Use a vacuum cleaner to remove dust.

3. If it’s very dirty, wash the filter with warm water and a neutral detergent.

4. Rinse it with cold water and let it dry naturally before putting it back in its place.

5. Once the filter has been reinserted, close the grille.

Note: The lower air filter is screwed on and cannot be removed.

Cleaning of casing:

Use a damp and soft cloth to clean the outer surface. Do not use excessively hot water, solvents, petrol, or other aggressive chemical compounds. Remove stains using lukewarm water with a little neutral detergent. Do not pour water onto the air conditioner.

Storage:

If not using the unit for a long time, clean the filters before storing. Keep the appliance in a vertical position at all times. Do not place heavy objects on top of it. It is advisable to protect the appliance with a plastic sheet.

Transport:

Transport the air conditioner in the vertical position. If this is not possible, rest it on its right-hand side. When the appliance reaches its final destination, place it immediately in the vertical position and wait at least 4 hours before operating it in cooling mode.

Check that:

• the unit intake and delivery grilles are always free;

• the air filters are always clean; a dirty filter will decrease the passage of air and reduce the unit’s performance;

• all doors and windows are closed to avoid infiltration of unconditioned air;

• the flexible pipe is correctly positioned, without tight bends or curves;

• the room temperature is above 16 °C in cooling and 10°C in dehumidifying.