Click here to download ELAN EL-SC-100 (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ELAN Quick Install Guide EL-SC-IOO

****** Page 2 ****** QUICK INSTALL GUIDE The Controller may be used as a standalone system controller or as an Extender to any gSC OR SC controller or running g!6.6 or greater. Please check the ELAN Training Guide for EL-SC-IOO control capabilities. The ELAN Training Guide contains valuable hardware and software reference documentation and is considered an important supplement to this document. Make sure you have the latest version by visiting the ELAN Dealer website at elanhomesystems.com and follow the Dealer Resources link. Included in the box: EL-SC-IOO Controller • 12vDC Power Supply Important Safety Instructions: 1. Read, understand and follow ALL safety and installation instructions included in this manual. Failure to follow the included documentation may damage the product and will void manufacturer’s warranty. 2 Follow ALL installation guidelines included with the product. Installation of the product in high humidity environments, in close proximity to heat sources and /or non-recommended locations will impede, interfere and/or damage the intended operation of the product g. Only use attachments and accessories which have been specified for use by the manufacturer. 4. The use of abrasive, liquid or solvent based cleaning fluids will damage the product. Please refer and follow all Product Care instructions included with the product. 5. Product Servicing may only be completed by authorized or certified service centers & personnel. For a complete list of product servicing options, please follow instructions included in the product documentation and /or contact original manufacturer for details. 2

****** Page 3 ****** EL-SC-100 FCC and IC Information: This Class B digital apparatus complies with Part 15 of the FCC rules and with Canadian ICES-OOS and RSS-247. Operation is subject to the following two conditions: 1. This device may not cause interference and 2 This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-24Z Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer djinterférence et (2) cet appareil doit accepter toute interférence, notamment Ies interférences qui peuvent affecter son fonctionnement. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC and IC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine evaluation limits in section 2.5 of RSS 102. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters from user and bystanders. 3

****** Page 4 ****** QUICK INSTALL GUIDE Warning: The device meets the exempt’on from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: (519) 763-4538. FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. 4

****** Page 5 ****** EL-SC-100 La puissance de sortie émise par l”apparei/ de sans fil est inférieure å la limite ‘exposition aux fréquences radio d’lndustry Canada (/C). Utilisez l’appareil de sans fil de faqon å minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d’exposition aux RF d’IC dans des conditions d’exposition des appareils mobiles (antennes sont supérieures å 20 cm å partir du corps dune personne). FCC and IC Registrations FCC II): EF400186 IC: 1078A-00186 5

****** Page 6 ****** QUICK INSTALL GUIDE EL-SC-IOO Overview Dimensions: 6.95 in. x 4.94 in. x 1.30 in. Power Button 00000 Status Indicator osc OSD RS-232 Rs-232 6 OUTPUTS IR Outputs AUDIO SENSE USS USB Audio Out Sense Input Reset DC Power LAN / PoE

****** Page 7 ****** EL-SC-100 Mounting The is designed to mount on a shelf, hang in a cabinet or rack, or mount in a structured wiring enclosure with optional mounting bracket. Wall Mounting: The EL-SC-IOO chassis has been designed to allow convenient wall mounting in any orientation. Arrows on the rear panel may be used to mark the location for the screws. Mark the screw locations, mount the screws leaving approx. 8/16″ (5mm) of screw exposed and slide the chassis over the screws. WALL Leave a 3/16 in. gap between screw heads and wall. gsn Use arrows to mark screw holes oso oranv C) 5 in. 7

****** Page 8 ****** QUICK INSTALL GUIDE Structured Wiring Cabinet Mounting: Using the optional Structured Wiring Cabinet Mount, the EL-SC-IOO can be mounted in a structured wiring cabinet. 1. Attach mounting bracket to wiring cabinet with snap rivets and washers 2. Snap the controller to the 2 hooks on the mounting bracket Shelf Mounting: The EL_SC-IOO has rubber feet to protect finished surfaces. Set the controller in a location that will allow you to properly manage connected wiring so that there is no tension on the connections.

****** Page 9 ****** EL-SC-100 Serial Connection Connect an RS-232 serial controlled device using an RJ45 connector (not included) to the RS232 port on the rear of the controller. The EL-SC-i00 serial connector is not compatible with RS-485 serial devices. If your project requires RS-485 connections you will need to use a gSC10 controller. Below is the wiring pin-out for the RJ45 connector. 1 2 3 4 5 6 .1 3 (DTR) 5 (RD) 7 (CTS) 8 (RTS) 9

****** Page 10 ****** QUICK INSTALL GUIDE Sense Input Connection ELAN sensors can be used to trigger events from 3rd party devices. The status is binary, either ON or OFF. This can be used to trigger an event map or as a condition of an event map. CONNECT ONLY an ELAN sensor to this port. Available ELAN sensors: Audio Sensor Video Sensor… Contact Closure Current / Magnetic Field Light/ LED Voltage IR Output Connection AUDSENSOR PIN: VIDSENSOR PIN: CTSENSOR CRSENSOR : LTSENSOR PIN: VTSENSOR Three discrete IR outputs are supplied to control third party devices. Each output is compatible with Xantech single and dual emitters DVD Media Player ooo OUTPUTS TV 10

****** Page 11 ****** EL-SC-100 HDMI Connection The includes an HDMI connector for an on screen display (OSD) interface. Connect the OSD output to an available HDMI input on a display or AVR USB Connection The USB connection is primarily designed for connecting the optional USB Z-Wave antenna. See the integration note for configuring Z-Wave devices through the EL-SC-IOO. LAN / POE Connection The EL-SC-IOO has a Gigabit POE compatible Ethernet port. Connect an Ethernet cable to an available port on the network. Note: The EL-SC-IOO can be connected via WiFi, however a wired connection is preferred. The EL-SC-i00 can be powered over Ethernet (PoE).The minumum POE requirement is IEEE 802.gat. 42.5 – 57 VDC, 600 mA maximum. RESET Button Located on the right side of the controller, is the recessed pinhole button that can be used in three ways: 1. 2 second press and release resets the controller to DHCP 2. 20 second press and release removes all configuration information. Software version will be maintained. g. While applying power, a iO second press and release will perform a full factory reset. Software will revert to factory default verison. DO NOT remove power during a factory reset as it will permanently damage the unit. Allow the unit to reboot and become discoverable (about 4 minutes). Note: the LED will remain red during the reset process. WARNING! THESE ACTIONS CANNOT BE UNDONE! II

****** Page 12 ****** QUICK INSTALL GUIDE Power Once all other connections have been completed, connect an Ethernet cable connected to a POE switch or the 12 VDC, IA power supply to the DC input. Power Button When the controller is off, a short press powers unit on When the controller is on, a short press (less than three seconds) restarts controller. When the controller is on, a long press (8 seconds or longer) powers down the controller LED Status Indicator The LED communicates the status of the controller: Blue = Connected 0K / Power Blue flashing = Boot up Amber No network found Red = Boot failure Red flashing = Self-check failure 12

****** Page 13 ****** EL-SC-100 Network Connection The is factory set to use DHCP Connect to a wired network and use the ELAN Configurator to connect to the controller. Once connected, use configurator to set a static IP address or connect via WiFi. Software Update Prior to configuring the controller, upgrade the software to the latest available version found on the ELAN Dealer Resources portal. Download and open the excecutable file and follow the on screen instrucitons. 13

****** Page 14 ****** QUICK INSTALL GUIDE Notes 14

****** Page 15 ****** EL-SC-100 Notes 15

****** Page 16 ****** Limited Warranty Nortek Security & Control ( INSC’ ) warrants the EU-SC-100 to be free from defects in materials and workmanship for the period of two years (2 years) from the date of purchase, If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly notifies ‘NSC’ in writingi ‘NSC’ shall repair or replace the item at the company’s option. This warranty shall not apply (a) to equipment not manufactured by ‘NSC’, (b) to equipment which shall have been installed by other than an ‘NSC’ authorized installer, (c) to installed equipment which is not installed to ‘NSC’s’ specifications, (d) to equipment which shall have been repaired or altered by others than ‘NSC’, (e) to equipment which shall have been subjected to negligence, accident, or damage by circumstances beyond ‘NSC’s’ control, includ’ng, but not limited to, lightning, flood, electrical surge, tornado, earthquake, or other catastrophic events beyond ‘NSC’s’ control, or to improper operation, maintenance or storage, or to other than normal use of service. With respect to equipment sold by, but not manufactured by ‘NSC’, the warranty obligations of ‘NSC’ shall in all respects conform to the warranty actually extended to INSC’ by its supplier. The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. Except as may be expressly provided and authorized in writing by INSC’, INSC’ shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured by INSC’ or services rendered by ‘NSC’. THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES EXCEPT WARRANTIES OF TITLE, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ATTENTION: TO OUR VALUED CUSTOMERS To ensure that customers obtain quality pre-sale and after-sale support and service, Nortek Security & Control products are sold exclusively through authorized dealers. Nortek Security & Control products are not sold online. The warranties on Nortek Security & Control products are NOT VALID if the products have been purchased from an unauthorized dealer or an online E-tailer. To determine If your Nortek Security & Control reseller is authorized, please call Nortek Security & Control at (707) 283-5900. SECURITY & CONTROL nortekcontrol.com All rights reserved. 02019 Nortek Security & Control. P/N: 10024269 (Rev B)

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELAN EL-SC-100 (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.