ELAN EL-IP-OBF2-WH (01) PDF MANUAL

ELAN EL-IP-OBF2-WH (01) PDF SUMMARY:

How do I begin using this camera?

If you are installing an ELAN Camera and/or ELAN NVR with an ELAN Controller, please refer to the “ELAN Surveillance” Integration Note for setup and software configuration. ELAN Integration Notes are served through the ELAN tools and on elanhomesystems.com/ dealer-resources. The software configuration information in this document can be used to extend device control parameters for use within an ELAN controller environment, or be used to operate this hardware independent of an ELAN controller.

---

What should I do if this equipment causes harmful interference to radio or television reception?

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

---

What is the first step to installing the camera?

Remove the camera from the box first. Connect the Ethernet cable and power cable to the camera’s RJ-45 network connector and DC power-in connector (FIG.1). Secure the camera to the wall (FIG.2).

---

How do I adjust the camera angle?

Adjust the five adjustment screws to move the camera to the desired angle, and then tighten the adjustment screws (FIG.3–8).

---

How do I optimize video images on a Vari-Focal Model?

Rotate focus and zoom knobs for optimal video images (FIG.9).

---

How do I insert a Micro SD card?

Rotate the front cover counterclockwise to remove it and insert a Micro SD card (FIG.10 & FIG.11).

---

What are the system architectures for connecting the EL-IP-OB Camera series to the network?

• Use DC12V power adaptor and network switch connected to a network.
• Use with PoE of the network switch connected to the network.
• Use PoE power injector and the network switch connected to the network.

---

How do I restore the hardware to factory default settings?

1. Press and hold RESET for 10 seconds before releasing.
2. The camera will be restored to factory default settings after approximately 90 seconds and will reboot automatically.
3. Search for the IP device using the IPScan software.
4. Start the IP device via an Internet browser.
5. Enter the default username “ELAN” and password “3526” to operate.

---

What is the default IP address of the camera?

The default IP address for each IP camera is 192.168.0.200. Cameras are configured to use DHCP by default but will revert to the default address 192.168.0.200 if a DHCP server is not available.

---

What should I check before accessing the IP cameras?

Before accessing the IP camera, make sure that the camera’s RJ-45 network, audio, and power cables are properly connected.

---

How do I set the IP address?

To set the IP address, consult your network administrator for an available IP address.

---

What software is required for online display of video?

Universal ActiveX software components are required for online display of MJPEG or H.264 Full HD video.

---

How do I install the ActiveX plug-in?

When you log in to the IP camera from Internet Explorer, a security warning dialog box will prompt the installation of the Universal ActiveX plug-in. Click Install to download it.

---

How do I ensure the ActiveX plug-in works on my computer?

Make sure your Internet browser allows the signed ActiveX plug-in to work on your computer. To do this, open Internet Explorer and go to Tools-> Options-> Security Settings. Set “Download Signed ActiveX plug-in controls” to “Prompt” and “Run ActiveX control and plug-in” to “Enable”.

---

What are the user authentication levels for accessing the IP camera?

There are two levels of user authentication: admin and guest. The administrator is authorized to reset basic mode settings and see live video, while the guest is only allowed to see live video.

---

What are the default usernames and passwords for the IP camera?

The default username is ELAN and the default password is 3526.

---

How do I log on to the IP camera?

To log on to the IP camera, please enter the username and password on the login page and click Submit to enter the system. Once complete, you can access the IP camera’s live video by entering the default IP address via your Internet browser. When the security warning dialog box appears, click OK to download the ActiveX plug-in directly from the IP camera.