Click here to download ELAN EL-IP-OBF4-WH (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** EL-IP-OBF2-WH / EL-lP-OBV2-WH EL-lP-OBF4-WH / EL-lP-OBV4-WH Quick Start Guide FIXED AUTO DISCOVER CONFIGURE VARIFOCAL BULLET OUTDOORI INDOOR 2MP 4MP WH ELAN SURVEILLANCE

****** Page 2 ****** ELAN BEGINNING USING THIS CAMERA IMPORTANT!! QUICK START GUIDE If you are installing an ELAN Cameras and/or ELAN NVR with an ELAN Controller, please refer to the “ELAN Surveillance” Integration Note for setup and software configuration. ELAN Integration Notes are served through the ELAN tools and on elanhomesystems.com/ dealer-resources. The software configuration information in this document can be used to extend device control parameters for use within an ELAN controller environment, or be used to operate this hardware independent of an ELAN controller. NOTES 2 elanhomesystems.com

****** Page 3 ****** EL-lP-OBF2-WH / ECIP-OBF4-WH / a-IP-OBV2-WH / EL-lP-OBV4-WH NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. contact techsupport@elanhomesystems.com 3

****** Page 4 ****** ELAN Unit: mm [Fixed Lens Camera] 185 65 5 62 I—- 77 158 68 69 QUICK START GUIDE [Varifocal Camera] 214 77 188 Ø70 42 48 5 elanhomesystems.com

****** Page 5 ****** EL-lP-OBF2-WH / ECIP-OBF4-WH / a-IP-OBV2-WH / EL-lP-OBV4-WH PART DESCRIPTION & DIMENSIONS O Sun Shield Q) Main Body O Front Cover O Bracket Base O Window O Lens C) RJ-45 Network Port (supports POE) O Power jack (DC12V O Micro SD card slot C Reset Key INSTALLATION . Remove the camera from the box first. Connect the Ethernet cable and power cable to the camera’s RJ-45 network connector and DC power-in connector (FIG. 1). Secure the camera to the wall (FIG.2). DC POWER INPUT NETWORK CABLE FIG I contact techsupport@elanhomesystems.com / FIG 2 5

****** Page 6 ****** ELAN QUICK START GUIDE 2. Adjust the five adjustment screws to move the camera to the desired angle, and then tighten the adjustment screws (FIG.3—8). FIG 3 FIG.5 FIG. 7 FIG. 4 FIG 6 FIG.8 elanhomesystems.com

****** Page 7 ****** EL-lP-OBF2-WH / ECIP-OBF4-WH / a-IP-OBV2-WH / EL-lP-OBV4-WH 3. Rotate focus and zoom knobs for optimal video images (FIG.9). NOTE: Van-Focal Model only. ZOOM FOCUS FIG. 9 INSERTING A MICRO SD CARD Rotate the front cover counterclockwise to remove it and insert a Micro SD card (FIG. 10 & FIG.1 1). FIG 10 contact techsupport@elanhomesystems.com o FIG II 7

****** Page 8 ****** ELAN QUICK START GUIDE SYSTEM ARCHITECTURES For connecting EL-IP-OB Camera series to the network, please follow one of the system architectures: (I). Use DCi2V power adaptor and network switch connected to a network. Fixed Lens CAMERA LAN / Internet Non-PoE Switch DC12V Adaptor (2). Use with POE of the network switch connected to the network. LAN / Internet Fixed Lens POE Switch CAMERA (3). Use POE power injector and the network switch connected to the network. Fixed Lens CAMERA 8 LAN Internet Non-PoE Switch POE Power Injector elanhomesystems.com

****** Page 9 ****** EL-lP-OBF2-WH / ECIP-OBF4-WH / a-IP-OBV2-WH / EL-lP-OBV4-WH EMERGENCY FACTORY DEFAULT To restore the hardware to factory default settings, please follow these steps: I . Press and hold RESET for 10 seconds before releasing. 2. The camera will be restored to factory default settings after approximately 90 seconds and will reboot automatically. g. Search for the IP device using the IPScan software. 4. Start the IP device via an Internet browser. 5. Enter the default username “ELAN” and password “3526” to operate. NOTE: Cameras are configured to use DHCP by default but will revert to the default address 192.168.0200 if a DHCP server is not available. BEFORE ACCESSING IP CAMERAS Before accessing the IP camera, make sure that the camera’s RJ-45 network, audio, and power cables are properly connected. To set the IP address, consult your network administrator for an available IP address. The default IP address for each IP camera is 192.168.0.200. Users can use the default IP address to verify the camera’s network connection. contact techsupport@elanhomesystems.com 9

****** Page 10 ****** ELAN SOFTWARE REQUIREMENTS QUICK START GUIDE Universal ActiveX software components are required for online display of MJPEG or H.264 Full HD video. When you log in to the IP camera from Internet Explorer, a security warning dialog box will prompt the installation of the Universal ActiveX plug-in. Click Install to download it. Internet Explorer • Security Warning Do you to “‘tstan this software? Nyct: video.cab (P Video Co.. Ltd. 10 fks frctn tit trterret cm be usefd, th$ fk cm Criy “ftwee froth trusts elanhomesystems.com

****** Page 11 ****** EL-lP-OBF2-WH / ECIP-OBF4-WH / a-IP-OBV2-WH / EL-lP-OBV4-WH INTERNET BROWSER SETTINGS & APPLICATION REQUIRED Make sure your Internet browser allows the signed ActiveX plug-in to work on your computer. To do this, open Internet Explorer and go to Tools-> Options-> Security Settings. Set “Download Signed ActiveX plug-in controls” to “Prompt” and “Run ActiveX control and plug-in” to “Enable”. Once complete, you can access the IP camera’s live video by entering the default IP address via your Internet browser. When the security warning dialog box appears, click 0K to download the ActiveX plug-in directly from the IP camera. There are two levels of user authenti- cation (admin and guest) that can access the IP camera. Administrator is authorized to reset basic mode settings andsee live video, while the guest is only allowed to see live video. The default usernames and passwords are as follows: Connect to Vitout a is uzrrørj’* Username Password ELAN 3526 To log on to the IP camera, please enter the username and password on the login page and click Submit to enter the system. contact techsupport@elanhomesystems.com 11

****** Page 12 ****** Your world, made simple’ main: 1 (800) 472-5555 -US 1 (707) 283-5900 – Intemational 1 (707) 283-5901 – Fax core Brands, LLC, 18COS Blvd., Petaluma, CA USA 02017 CDre Brands, LLC. All rights ELAN is a registerBd trademark ot Core Brands, LLC, tech support: techsupport@elanhomesystems.com web: elanhomesystems.com 10019486 Rev-AO, 11/2017

FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL



ELAN EL-IP-OBF4-WH (01) PDF MANUAL

Leave a comment, question, review or page error below. Account not required.

This site uses Akismet to reduce spam. Learn how your comment data is processed.