DYACO SPIRIT 7.0S (01) PDF DOCUMENT

The serial number sticker for your DYACO SPIRIT 7.0S is located on the console upright. You should record the number below the barcode for warranty registration purposes.

To reduce the risk of injury, please read all instructions before using the DYACO SPIRIT 7.0S. Key safety instructions include:

1. Do not modify this equipment without authorization from the manufacturer.

2. Install the 7.0S on a flat, level surface with access to a 100 to 240-volt AC, 50/60 Hz, 15-amp outlet. The 7.0S should be the only appliance in the electrical circuit.

3. Use this 7.0S only for its intended use as described in the manual.

4. Keep children away from the 7.0S. There are moving parts, obvious pinch points, and other caution areas that can cause harm.

5. Except as instructed, keep hands away from all moving parts.

6. Keep the electrical cord away from heated surfaces and travel lanes. Do not operate if the cord or plug is damaged.

7. Never drop or insert any object into any openings.

8. Do not use the DYACO SPIRIT 7.0S outdoors.

9. To disconnect, turn all controls to the off position, then remove the plug from the outlet.

10. This 7.0S is designed for commercial use and meets the demands of orthopedic, sports wellness, and general conditioning programs.

11. Do not attempt to use your 7.0S for any purpose other than its intended purpose.

12. The pulse sensors are not medical devices. Their accuracy can be affected by various factors, including user movement. They are intended as exercise aids for determining heart rate trends.

13. The heart rate monitoring system may be inaccurate. Over-exercise may result in injury or death. If you feel faint, stop exercising immediately.

14. Ensure a minimum of two feet of space on the sides and at least one foot of free space at the front and rear of the 7.0S for proper operation and safety.

15. Do not use any aftermarket parts on this 7.0S other than those recommended by Spirit by Dyaco.

16. Do not attempt any servicing or adjustments other than those described in the manual. All other work must be performed by trained service personnel.

17. Installation and assembly should be performed by trained personnel only.

18. To avoid injury, please observe all minimum and maximum seat adjustment settings.

19. The user weight limit is 440 lbs.

WARNING! Never remove any cover without first disconnecting AC power. If voltage varies by 10% or more outside the specified range (90 to 240V), performance may be affected, which is not covered under warranty. If you suspect low voltage, contact your power company or a licensed electrician.

Key guidelines include:

• Never expose the 7.0S to rain or moisture. It is not designed for use outdoors, near a pool, spa, or in any high-humidity environment.

• The 7.0S is not protected against the ingress of water or particulate matter.

• The 7.0S is not suitable for use in an oxygen-rich environment.

The DYACO SPIRIT 7.0S is designed for operation in normal climatic surroundings (IEC 60601-1):

• Temperature: +10°C to +36°C

• Relative humidity: 30% to 90% (non-condensing)

• Air pressure: 700 to 1060 mbar

• Maximum operating altitude: approx. 10,000 feet (3000m), without pressurization

• Transport and store the 7.0S at a temperature of -20°C to +50°C.

The DYACO SPIRIT 7.0S must be grounded. Grounding provides a path of least resistance for electric current in case of a malfunction, reducing the risk of electric shock. This product has a cord with an equipment-grounding plug. The plug must be connected to an appropriate outlet that is properly installed and grounded according to all local codes and ordinances.

DANGER – Improper connection of the equipment-grounding conductor can result in a risk of electric shock. If you are unsure whether the product is properly grounded, check with a qualified electrician or serviceman. Do not modify the plug provided with the product if it does not fit the outlet; have a proper outlet installed by a qualified electrician.

WARNING!

• Never use your 7.0S during an electrical storm, as power surges could damage its components.

• All users should obtain medical clearance before starting any rigorous exercise program, especially those with a history of heart disease or other high-risk factors.

• The user should adjust the seat to a comfortable position. The console has a setup menu program to help set the correct seat position.

• Start at a safe exercise level and do not allow the user to overexert themselves. Watch for symptoms like shortness of breath, difficulty breathing, pain, discomfort, or feeling faint.

• Ensure the user warms up and cools down properly (three to five minutes each) to avoid over-taxing the cardiovascular system.

• The 7.0S should not be used for patients with severe osteoporosis, non-union fractures, debilitating dizziness, or poor safety awareness/cognition. Do not use for patients weighing more than 440 lb (bariatric). Do not use for patients with acute conditions such as pulmonary embolus, thrombus, acute MI, acute fractures, or BP over 180/110 Hg.

• SAVE THESE INSTRUCTIONS – THINK SAFETY!

MEDICAL PURPOSES

• Patient warm-up before a physical therapy session.

• Have the patient walk to improve ambulation and range of motion after knee/hip/ankle surgery or neurological conditions.

• Allow patients to perform cardiovascular exercise.

• Used for open kinetic chain exercise only; the patient is not restrained or connected to the 7.0S.

• The 7.0S is a device intended to be used to redevelop muscles or restore motion to joints.

INTENDED PATIENT POPULATION

• Male and Female Adults. Children may use it at the discretion of a Qualified Physical Therapist and/or with parental consent.

• Maximum patient’s weight is 440 lb.

• Patient must be ambulatory.

• Patient should have medical clearance before starting any rigorous exercise program. This is especially important for individuals with a history of heart disease or other high-risk factors.

• Environment: Intended for indoor use in environments with hygienic requirements. Not designed for outdoors, near a pool/spa, or in high humidity.

• Visibility: Standard ambient room lighting is sufficient. Viewing distance is 1m and viewing angle is 120°.

• Physical Conditions:

– Temperature range: 10°C ~ 36°C

– Relative humidity range: 30% R.H. ~ 90% R.H., non-condensing

– Hygienic requirements: No particular restrictions.

• Frequency of Use: Dependent on the therapist’s plan.

• Location: Intended for hospital, clinic, home use, and research in academic institutions.

• Mobility: The product is intended to be fixed.

The patient pushes the pedals with their feet and the arms with their hands. The operator can increase or decrease the workload using the Up and Down keys on the console. When a workload change is requested, a gear motor moves permanent magnets closer to or further from the aluminum flywheel, creating more or less resistance.

The DYACO SPIRIT 7.0S is used for physical rehabilitation for orthopedic and neurological problems, as well as in sports medicine, wellness, and general conditioning.

TYPICAL APPLICATIONS:

• Patient warm-up before a physical therapy session.

• Pedaling to improve range of motion after knee/hip/ankle surgery.

• Performing cardiovascular exercise.

UNIQUE USES:

• Self-adjustable step length allows patients to pedal in a smaller range of knee motion, from 5 degrees to full range.

• Arms are linked to the foot pedals for ease of coordination and can also be used alone.

• A symmetry program measures the balance between left and right pedal/arm strokes, with a graphical bio-feedback display to motivate even power symmetry.

• If measuring arms only, the graph and power readings will be reversed.

OTHER FEATURES:

• Work range up to 750 watts (at 60 RPM) with level settings at 15 watts per level.

• Indexed seat positioning accommodates users from 147 cm to 200 cm (4′ 10″ to 6′ 7″).

• Heart Rate monitoring using the optional heart rate chest-strap.

No, the heart rate function on the DYACO SPIRIT 7.0S is not a medical device and should not be relied upon when accurate readings are necessary. Various factors, including user movement, may affect the accuracy of the heart rate reading. The heart rate reading is intended only as an exercise aid for measuring heart rate trends in general. Some individuals, such as those in a cardiac rehab program, may benefit from using an alternative heart rate monitoring system like a chest or wrist strap.

A. Console

B. Upper Body Rotating Handles

C. Quick Release Lever

D. Cushioned Footplates with straps

E. Lifting handle for transport

F. Leveling glides

G. Seat angle adjustment

H. Seat swivel adjustment

I. Seat position adjustment

1. Cut the straps, then lift the box over the unit and unpack.

2. Carefully remove all parts from the carton and inspect for any damage or missing parts. If parts are damaged or missing, contact your dealer immediately.

3. Locate the hardware package. Remove the tools first.

4. Remove the hardware for each step as needed to avoid confusion. The numbers in the instructions that are in parenthesis (#) are the item number from the assembly drawing for reference.

Assembly – Step One (Seat Assembly)

1. Slide the seat carriage (20) all the way back. Slide the handle bar assembly (17) onto the seat frame (20). Secure it with two 3/8″ x 3-1/4″ bolts (140), four flat washers (170), and two nylon nuts (190). Install the safety cover (108) and seat belts (233) onto the bolts before the washers and nuts. Install four 3/8″ x 2″ bolts (132) from the top, with eight 3/8″ flat washers (170) and 3/8″ nylon nuts (190).

2. Attach the seat back gas shock (109) to the handle bar assembly (17) using a 5/16″ x 1-1/4″ bolt (135), two 5/16″ flat washers (173), and a 5/16″ nylon nut (193).

3. Assemble the swivel seat latch handle (22) to the seat assembly (20) with two 6mm x 40mm bolts (129), four 5/16″ curved washers (185), and two 6mm nylon nuts (187).

4. Plug the hand pulse connectors from the handlebars into the seat carriage.

5. Assemble the rubber isolators (82) and pedals (28) to the pedal foot plates using six M5 Phillips screws (181) per side.

6. Press the four stabilizer end caps (31) into the stabilizer tubes. You may tap them in with a rubber mallet.

Assembly – Step Two (Console Mast)

1. Install the transport wheels (77) using 5/16″ x 1-3/4″ bolts (152) and 5/16″ nylon nuts (193).

2. Slide the console mast cover (74) onto the console mast (2), ensuring correct orientation.

3. Snake the computer cable through the console mast and slide the mast onto the receiving brackets, ensuring the cable is not pinched.

4. Fasten the mast with two 3/8″ x 2-1/2″ bolts (154), 3/8″ split washers (194), and 3/8″ flat washers (170) on the left side, securing with two 3/8″ nylon nuts (190). Install two 8mm x 16mm bolts (153) and curved washers (184) through the front and rear holes in the mast.

Assembly – Step Three (Seat Back and Cushion)

1. Slide the seat back assembly (94) into the seat back angle adjustment bracket. Secure with two 3/8″ x 1-3/4″ bolts (197), 3/8″ washers (167), and 3/8″ nuts (190).

2. Assemble the seat cushion (93) onto the seat frame with four M6 bolts (122).

Assembly – Step Four (Console and Arms)

1. Connect the computer cable to the back of the console and install the console (29) onto the mast, securing with four 5mm x 12mm screws (143).

2. Install the left and right arms (3&4) using 3/8″ x 3/4″ bolts (216), 3/8″ flat washers (217), 3/8″ split washers (243) on the sides, and 3/8″ curved washers (218) on the front and rear. Tighten bolts securely.

3. Remove the Allen screws from the lever clamps (111), fit them onto the handlebar (17), and secure them. Position the levers for comfortable reach. The left lever (gray cable) is for fore/aft seat adjustment; the right lever (black cable) is for seat back angle.

Plugging In

The DYACO SPIRIT 7.0S uses a universal switching power supply. You can plug it into any A.C. power source from 100 to 240 volts, 50 to 60 Hz. The A.C. input is located at the front of the unit.

Leveling the 7.0S

Once assembled and placed on a flat floor, you may need to adjust the leveling glides for stability. Use a 1/2” wrench to loosen the top nut of the levelers. Screw the two center levelers all the way in. Adjust the 4 corner levelers by hand to remove any wobble. Then, unscrew the 2 center levelers until they touch the floor. Finally, tighten all top nuts against the bottom of the stabilizer tubes, ensuring the bottom nut remains cinched against the leveling foot.

Adjusting the Seat Fore/Aft Position

Squeeze the brake handle located on the left side handlebar. Move the seat to the desired position and lower the handle. Move the seat slightly until the seat lock clicks into place. A numbered scale on the aluminum seat slide tube allows for repeatable settings. The position is indicated by the front of the seat carriage lining up with the number on the scale.

Adjusting the Seat Back Angle

Squeeze the brake handle on the right side handlebar and move the seat back to the desired position. A numbered scale just below the seat back cushion allows for repeatable settings.

Rotating the Swivel Seat

Lift the handle behind the seat to disengage the latch. Rotate the seat to the desired position. Lower the handle as you approach the position to activate the latch. The seat will latch into place every 45 degrees.

Pedal Strap Adjustment

The ankle and foot Velcro straps are easy to open and close. Remove the ankle strap from the chrome ring. Loosen the foot strap enough for the patient’s foot to slide under. Once the foot is positioned correctly, reattach the ankle strap and adjust both straps for a snug fit.

Seat Belt Adjustment

Simply snap the buckles together and adjust the strap to the desired fit.

Rotating Handle

The handles rotate to allow patients to use their upper body without wrist discomfort.

1. Quick Start is the fastest way to begin an exercise session. After the console powers up, simply press the START key to initiate the Quick Start mode.

2. In this mode, the time will count up from zero, all workout data will start to accrue, and you can adjust the workload manually by pressing the up or down key. The dot matrix will display the lowest resistance level initially. As you increase the workload, more rows will light up, indicating a harder workout.

3. The graphic display has 20 columns of lights, each representing 1 minute in Quick Start. After 20 minutes, the display will wrap around and restart at the first column. There are 20 levels of resistance displayed in 8 rows of lights.

1. Graphic display: Shows workout profiles.

2. Message window: Displays prompts and workout data.

3. Program keys: (Manual, Hill, Plateau, etc.) to select programs.

4. Function keys: (Fan, Start, Stop, Enter, Level +/-, On/Off).

5. Data displays: (SPM, CALORIES, TIME, STEPS, PULSE).

6. HR percent profile: Shows heart rate as a percentage of max.

7. Set Up key: Accesses the setup menu.

Power On & Console Operation

When initially powered on, the console performs an internal self-test where all lights turn on briefly. It will then show the software version and the total hours the unit has been used. After a few seconds, the console enters Idle Mode, with a scrolling start-up message. You can now begin using the 7.0S.

The console will automatically power down after 20 minutes of inactivity. Press any key to wake it up. Always disconnect the main power when the 7.0S is not in use.

Set Up Menu

Press the Set Up key to enter patient data and customize settings. Use the up/down arrows to scroll through the menu and press Enter to select an option.

• Position (seat and arm position setting): You can input the user’s height (in inches or cm) and the software will calculate a suggested position for the seat and arms. This is an aid and may need slight adjustments based on the patient’s body symmetry.

• Track or step graph: The segmented track around the profile display can be set to show either a track or a foot position indicator. During any program, you can press the Symmetry key to switch between these displays.

Displays

• Graphics Display (Dot Matrix): Shows work profiles and the symmetry graph. The profile indicates resistance changes during a program. The peak resistance level can be set during setup and adjusted during the workout.

• Data Display Windows: Provide exercise information such as SPM (steps per minute), calories, time, steps (total), and pulse. Resistance level and watt measurements are shown on either side of the graphic display.

• Message Window: This is the main display for programming and in-program data. It shows measurements like average watts (left/right), METS, symmetry, and segment time.

• Heart Rate Bar Graph: Displays your heart rate as a percentage of your maximum, which is calculated based on the age you enter in Set Up. It activates when you grasp the hand pulse sensors or wear a chest strap transmitter.

Function Keys

• Stop/Reset Key:

– Press once during a program to pause. Press Start to resume.

– Press twice during a workout to end the program and show a summary.

– Hold for 3 seconds to perform a complete console reset.

– During data entry, it acts as a “back” button to the previous screen.

• Enter Key: Used for confirming data during programming and for scrolling through different data in the message window during exercise.

• Program Keys: In idle mode, you can press a program key to preview its profile. To start it, press the corresponding key and then Enter. During data entry (age, weight, etc.), these keys also function as a number pad (Manual is 1, Hill is 2, etc.).

The Manual program allows you to control the workload yourself, not the computer.

1. To start, press the Manual key, then press the Enter key.

2. The message window will prompt you to enter age, weight, and time. You can use the up/down keys or the numeric keypad (program keys) to enter the data, pressing Enter after each to proceed.

3. If you want to start immediately without changing settings, just press the Start key. This will use the default data from the set-up menu.

4. After editing settings, press the Start key to begin. You can go back and modify settings by pressing the Enter key.

During the program, you can scroll through workout data in the message window by pressing the Enter key. When the program ends, you can press Start to repeat it, Stop to exit, or save it as a custom program.

The DYACO SPIRIT 7.0S has three preset exercise programs. The dot matrix profiles are pictures of the workout, and adjusting the level will increase the workload, not change the picture.

• Hill: This program follows a pyramid-style progression, simulating going up and down a hill. The resistance steadily increases and then decreases.

• Cardio: Designed to increase cardiovascular function, this program builds heart muscle and increases blood flow and lung capacity by using a higher level of exertion with slight work fluctuations.

• Plateau: This program provides a steady-state exercise with warm-up and cool-down periods.

• Interval: This program alternates between high-intensity periods and low-intensity recovery periods. This helps increase endurance by depleting and then replenishing oxygen levels, training your cardiovascular system to use oxygen more efficiently.

1. Select the desired program button (e.g., Hill, Cardio) and then press the Enter key.

2. The message window will prompt you to enter age, weight, time, and max level for the program. “Max level” refers to the peak resistance setting. Use the up/down keys or the numeric keypad to enter values, pressing Enter after each.

3. After finishing edits, press the Start key to begin. You can go back and modify settings by pressing the Enter key. At any time during editing, you can press the Stop key to go back one level.

4. During the program, you can scroll through data in the message window by pressing the Enter key.

5. When the program ends, you can press Start to repeat it, Stop to exit, or save the workout as a custom program by pressing a user key and following the prompts.

The User 1 & 2 programs allow you to build and save a custom program.

Designing and Saving a New Program

1. Press either user key, then press Enter to begin programming.

2. The message window will show “name – a”. Use the up/down keys to change the first letter, then press Enter to save it and move to the next letter. When finished entering the name, press the Stop key to save the name and continue.

3. Enter an age using the up/down keys or numeric pad, then press Enter.

4. Enter a weight and press Enter.

5. Adjust the time and press Enter.

6. Adjust the max level (the peak exertion level for the program) and press Enter.

7. The first column of the profile will blink. Adjust the level for the first segment and press Enter. The next segment will default to the same level. Repeat this process for all twenty-four segments.

8. After setting all segments, the message window will prompt you to press Enter to save. It will then confirm “new program saved” and give you the option to start or modify it. Press Stop to exit to the start-up screen.

Running a Saved Program

1. Press the user key for the program you wish to run, then press Enter.

2. Enter the desired time and press Start to begin.

The Symmetry program aids in achieving a more balanced stroke, beneficial for patients with bi-lateral deficiencies. It measures left and right power, and the dot matrix displays a graph showing leg power symmetry for visual feedback. The program also works for upper body only; note that when pushing the handles, the graph is reversed (left side displays right arm info).

How to Use:

1. Press the Symmetry key, then press the Enter key.

2. Enter the age, weight, and time for the program using the on-screen prompts.

3. When finished, press the Start key to begin. You can modify settings by pressing Enter before starting.

4. During the program, scroll through data (watts, symmetry, METS) in the message window by pressing the Enter key.

For Best Results:

The program starts at level 1. You must manually increase the resistance by pressing the up arrow. Set the resistance high enough to generate a meaningful measurement but low enough for the patient to complete full pedal strokes without discomfort. Very low resistance may result in erratic measurements.

Biofeedback Graph:

The message window shows an average watt measurement for each leg (e.g., “WL 41 34” means the left leg is producing 41 watts and the right is producing 34 watts). The graph reflects the higher wattage. If power is equal, only two dots will be lit at the bottom center of the screen. Press Enter to view the Symmetry data.

The software works with newer 7.0S consoles with USB ports, on Windows 10, 7, and XP (with .Net Framework 2.0). Data is output in a .CSV file format. Please follow the website instructions to download the software.

Step 1: Install Software

Download the software. Connect the console to the computer using a USB cable (type A to type B). During installation, a security warning pop-up will appear. Click “Install”.

Step 2: Connect to Port

In the “Data Transfer V1.0” window, click “Connect” or “Change”. A “Pop-Up COM Port Selection Window” will appear. Select the correct COM port and click “Connect”.

Step 3: Record Data

Once the status shows “Connected” and “7.0S”, choose a file path and create a file name for the data. Click the “Record” button to start collecting data. To stop, click “Stop” in the software or quit the program on the console. The saved .CSV data file can be found at the assigned destination.

The chest strap transmitter is an optional, separate purchase. Most transmitters operating at 5kHz frequency will work.

1. Attach the transmitter to the elastic strap.

2. Adjust the strap to be as tight as possible without being uncomfortable.

3. Position the transmitter in the middle of your body, with the logo facing away from your chest. Some users may need to position it slightly left of center.

4. Secure the strap around your chest, immediately below the pectoral muscles.

5. Sweat is the best conductor for the signal. You can also pre-wet the electrodes (two black square areas on the reverse side) with plain water. It is recommended to wear the strap for a few minutes before your workout to establish a strong signal.

6. Your workout must be within range of the console to maintain a good, strong, reliable signal.

The transmitter activates automatically when it detects heart activity and deactivates when it doesn’t. Although water-resistant, moisture can create false signals, so dry the transmitter completely after use to prolong battery life (est. 2500 hours). If your strap has a replaceable battery, the replacement is a CR2032.

Caution! Do not use the 7.0S for Heart Rate Control unless a steady, solid Actual Heart Rate value is being displayed. High, wild, or random numbers indicate a problem.

Areas to check for interference that may cause erratic heart rate:

1. The Recumbent Stepper is not properly grounded.

2. Microwave ovens, TVs, small appliances, etc.

3. Fluorescent lights.

4. Some household security systems.

5. A perimeter fence for a pet.

6. Some people have issues with the transmitter picking up a signal from their skin. Try wearing the transmitter upside down.

7. The receiving antenna is very sensitive. If there is an outside noise source, turning the whole machine 90 degrees may de-tune the interference.

8. Another individual wearing a transmitter within 3 feet of your machine’s console.

If you continue to experience problems, contact your dealer.

1. Press the HR key, then press the Enter key.

2. The message window will ask for your Age. Enter it using the Up/Down keys or numeric pad, then press Enter.

3. You are now asked to enter your Weight. Adjust the number and press Enter.

4. Next is Time. Adjust the time and press Enter.

5. Now you are asked to adjust the Heart rate Level. This is the target heart rate level for the program. Adjust the level and press Enter.

6. You are now finished editing. Press the Start key to begin your workout. You can go back and modify settings by pressing the Enter key. (Note: During editing, press the Stop key to go back one level).

7. To increase or decrease the workload (and target heart rate) during the program, press the Up or Down key.

8. During the HR program, you can scroll through data in the message window by pressing the adjacent Display key.

9. When the program ends, you can press Start to begin again, Stop to exit, or save it as a custom program by pressing a user key.

Post-Workout Machine Care

Wipe down all areas in the sweat path with a damp cloth after each workout. If a squeak, thump, or clicking develops, it is likely due to one of two reasons:

1. Hardware was not sufficiently tightened during assembly. All bolts should be tightened as much as possible, possibly requiring a larger wrench.

2. The crank arm nut needs to be retightened. If noise persists, check that the unit is properly leveled using the 14mm wrench on the leveling pads on the rear stabilizer.

General Care

1. Store your machine according to the instructions when not in use.

2. Use a slightly damp cloth to clean areas where sweat or oil made contact.

3. Use a microfiber cloth to clean the screen and remove oils and other damaging substances.

4. Avoid leaving paper or small debris in the cupholders.

Sanitizing Your Spirit Fitness Equipment

• Hard Surfaces: Unupholstered high-contact surfaces (hard plastics) can be sanitized using a 75% isopropyl alcohol solution and a clean, dry cloth. Spray the surfaces, wipe clean, and allow them to dry before use.

• Soft Surfaces: For upholstered or soft-plastic surfaces, use a conditioner after sanitizing, following the conditioner manufacturer’s instructions.

To enter the Maintenance menu (or Engineering mode), press and hold the Start, Stop, and Enter keys simultaneously for about 5 seconds. The message window will display “Maintenance mode”. Press the Enter button to access the menu below:

• Key Test

• LCD test

• Functions

– Sleep mode – on

– Pause mode – on (If off, the console remains paused indefinitely unless Stop or Start is pressed).

– Odometer reset

– Units – English or Metric

• Service

– Motor test: Runs the resistance motor from level 1-20 and back to 1.

– Position sensor value is shown in the STEPS data window.

• Sensor Test

– SPM window shows reflector sensor #1 signal (1 or 0).

– CALORIES window shows reflector sensor #2 signal.

– TIME window shows Left step position counter.

– STEPS window shows Right step position counter.

– PULSE window shows speed sensor signal (on or off).

Error Messages

• EEPROM Error: The solution is to replace the console. This is the only error message.

• Motor Error: This means the resistance motor did not respond as expected. Press stop to enter idle mode. The console can still be used, but there will be no resistance changes. Try disconnecting the power for one minute and reconnecting. If this does not solve the problem, call for service.

No Power

• Make sure the A.C. outlet has power (90-240VAC) and the line cord is plugged securely into the AC adapter.

• Check the connection of the DC power wire where it enters the 7.0S.

• Make sure all connectors in the back of the console are securely seated.

Console Programs Do Not Start

• Perform the Keypad test in Maintenance mode.

• If you cannot access the test and the keys seem to have no effect, the keypad has malfunctioned.

Program starts but no data registers when pedaled:

• Check that connectors are properly seated in the back of the console.

• Perform the Sensor tests in Maintenance mode. If one sensor doesn’t work, it needs replacement. If both don’t work, it could be a bad console or both sensors are bad.

Symmetry measurement is incorrect:

• Perform the sensor tests in Maintenance Mode.

Pedal resistance seems harder/different than before:

• Check the watts per level setting in the Set Up menu. The factory default is 5 watts per level.

Cannot adjust seat or seat adjustments will not lock:

• Adjust the thumb nuts at the rear of the seat adjustment levers. If the cables have stretched, the latch may not disengage or engage properly. Adjusting the thumb nut can remedy this.

Clicking noise when pedaling:

• Make sure the pedal is tightened properly.

• Make sure the swing arms are securely tightened where they attach to the 7.0S.

• Check that the leveling feet on the bottom of the 7.0S are adjusted properly.

One pedal has no resistance but the other does:

• The drive cable has jumped off the pulley system.

REF: 7.0S

Dimensions:

• Length: 67″

• Width: 30″

• Height: 48″

Weight: 257.4 Lbs. (117 Kgs)

Work load: 5 watts up to 1000 watts.

Patient weight capacity: 440 Lbs. (200 Kgs.)

Readouts: Time and Segment time remaining, RPM, Watts (Left and Right), METS, Symmetry Index, Heart Rate, Calories, Work Level

Input power: 12 VDC, 2.74 Amps

Fuse rating: No user replaceable fuse

Resistance: Isokinetic with 20 levels of effort

External power supply:

• Sinpro model # HPU32A-105, 30 watt power supply

• Input: 100-240V ~; 50/60 Hz: 0.6-0.4A

• Output: 12 VDC, 2.74 A

• Input to output: 2MOPP

Disposal: Reference should be made to local regulations concerning the disposal of this product at the end of its useful life.

CERTIFICATIONS: CAN/CSA-C22.2 No. 60601-1:14, ANS/AAMI ES60601-1:2005+A2 (R2012) +A1, MDD 93/42/EEC Class Im, IEC 60601-1-2:2007, EN 60601-1-2:2007, IEC 60601-1:2005, EN 60601-1:2006+A11+A12, EN ISO 20957:2013, ISO 14971; 2012

The DYACO SPIRIT 7.0S is intended for use in the electromagnetic environment specified below. The customer or user should assure that it is used in such an environment.

Guidance and manufacturer’s declaration – electromagnetic compatibility

Recommended separation distances between portable and mobile RF communications equipment and the 7.0S

Note: If the device is interfered by a power or signal cable, image quality may be reduced or abnormally displayed. Such interference images could be easily identified and differentiated from the physiological characteristics of a patient and longer clinical time consumed but wouldn’t have any diagnostic accuracy issue. If there is a certain frequency of image interference, there is a need for isolation or filtering of the RF signal.