CUISINART DLC-2009M (01) PDF Document

To ensure safe operation of your CUISINART DLC-2009M, please follow these precautions:

1. Read all instructions before use.

2. Blades are extremely sharp. Handle them with care.

3. Always unplug the unit from the outlet when it is not in use, before assembling or disassembling parts, before cleaning, and before removing food.

4. Do not touch moving parts. Keep hands, hair, clothing, spatulas, and other utensils away from moving blades or discs during operation to prevent injury or damage to the food processor.

5. Never feed food by hand. Always use the food pusher.

6. Ensure the work bowl cover is securely locked in place before operating the appliance.

7. Do not attempt to defeat the cover interlock mechanism.

8. Never store any blade or disc on the motor shaft. To reduce the risk of injury, no blade or disc should be placed on the shaft except when the bowl is locked in place and the processor is in use.

9. Before use, check the work bowl for the presence of foreign objects.

10. Do not use this appliance for anything other than its intended purpose.

11. Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.

12. Ensure the appliance is off before plugging the cord into a wall outlet.

13. This appliance is not intended for use by children or by persons with reduced physical, sensory, or mental capabilities.

14. Do not operate your appliance in an appliance garage or under a wall cabinet.

15. To protect against risk of electrical shock, do not put the motor base in water or other liquid.

Follow these steps to assemble your CUISINART DLC-2009M:

Step 1. With the base on a flat, dry countertop, place the work bowl on top of the housing base. Turn the work bowl counter-clockwise to lock it onto the base. The handle should be slightly to the left of the center front.

Step 2. Carefully pick up the metal blade or dough blade by its center hub and place it over the motor shaft. For slicing or shredding, insert the disc stem over the motor shaft first, then place the slicing/shredding disc on the stem, ensuring the desired cutting side is facing up.

Step 3. Place the work bowl cover on the work bowl, with the feed tube on the left side of the handle.

Step 4. Turn the cover counter-clockwise to lock it into place. The feed tube should be positioned just to the right of the handle. The locking tab on the cover must slide completely under the locking post on the work bowl rim for the unit to operate.

Step 5. Insert the pusher assembly into the feed tube. The pusher assembly consists of two pieces: a small pusher nested inside a larger one. Use the large pusher for large produce and both for smaller produce.

Step 6. Plug the food processor into an appropriate electrical outlet.

The CUISINART DLC-2009M has a simple two-control system:

1. **ON Control:** Pressing the “ON” control paddle turns the motor on and allows the machine to run continuously. To stop the machine, press the “PULSE/OFF” control paddle.

2. **PULSE/OFF Control:** This control has two functions.

– To turn the machine off from continuous run, press the “PULSE/OFF” control paddle.

– To use the pulse function, press and release the “PULSE/OFF” control paddle as needed. This allows you to start and stop the machine quickly for short processing tasks. The motor will run as long as you hold the paddle down.

The CUISINART DLC-2009M is equipped with a motor overload protection feature. If the motor is subjected to an excessive strain for an extended period, such as when processing a very hard or large load, a thermal protector in the motor will trip to prevent damage. If this happens, the machine will stop running.

To reset it:

1. Press the “PULSE/OFF” control.

2. Unplug the unit.

3. Allow the motor to cool down for 20-30 minutes.

4. Reassemble the unit and resume processing. You may need to process the food in smaller batches.

For chopping or mixing, use the metal chopping/mixing blade. Follow these steps:

1. Assemble the work bowl and the chopping/mixing blade on the CUISINART DLC-2009M base.

2. Cut food into uniform pieces, about 1-inch (2.5 cm) in size.

3. Place the food into the work bowl. Do not overfill. Refer to the maximum capacity chart.

4. Place the cover on the work bowl and lock it.

5. For a coarse chop, use the “PULSE/OFF” control to pulse the machine. Check the consistency frequently.

6. For a fine chop or mincing, press the “ON” control to run the machine continuously until the desired consistency is achieved.

7. To add liquid ingredients while the machine is running, pour them through the small feed tube opening in the pusher assembly.

To shred or slice with your CUISINART DLC-2009M, use the reversible slicing/shredding disc. The disc is labeled on each side for its function.

1. Place the detachable disc stem over the motor shaft in the work bowl.

2. Place the disc on the stem with the desired cutting surface facing up (either shredding or slicing).

3. Lock the work bowl cover in place.

4. Prepare the food by cutting it to fit the feed tube. For best results, food should be cut with flat ends.

5. Pack the feed tube with food. Use the large pusher for large items or both the small and large pushers for smaller items. For long foods like carrots, you can pack them vertically.

6. Press the “ON” control to start the motor.

7. Apply light, even pressure to the pusher to guide the food through the feed tube and over the disc.

8. Never put your fingers in the feed tube. Always use the pusher.

To knead dough, use the plastic dough blade. The CUISINART DLC-2009M can knead dough using up to 2.5 cups (600 ml) of all-purpose flour.

1. Assemble the work bowl with the dough blade inside.

2. Place the dry ingredients into the work bowl and process for about 5 seconds to combine them.

3. With the machine running on “ON,” add the liquid ingredients through the small feed tube in a steady stream, as quickly as the flour absorbs them.

4. After the liquid is added, continue processing until the dough cleans the sides of the bowl and forms a ball. This typically takes 30 to 40 seconds.

5. Do not process the dough for more than 60 seconds. Over-processing can overheat the motor.

6. After processing, turn the dough out onto a lightly floured surface and knead by hand for 1-2 minutes. Then let it rise according to your recipe.

Follow these instructions for cleaning your CUISINART DLC-2009M:

1. Always unplug the unit before cleaning.

2. Handle the blades and discs with extreme care as they are very sharp. Do not leave them to soak in soapy water where they may be unseen.

3. All removable parts are dishwasher safe. It is recommended to place them on the top rack. For the work bowl, it’s best to place it upside down.

4. If washing by hand, use a mild soap or detergent. Rinse thoroughly and dry immediately to prevent spotting.

5. To clean the motor base, wipe the exterior with a damp cloth or sponge. Dry it immediately. Never immerse the motor base in water or put it in a dishwasher.

6. Do not use abrasive cleansers on the motor base.

Here are some tips to get the best results from your CUISINART DLC-2009M:

– For best results, do not overfill the work bowl.

– Process foods in batches if necessary.

– Use the pulse function for better control over chopping tasks to avoid over-processing.

– When slicing or shredding, cut food into pieces that fit the feed tube. For soft cheeses, chill them thoroughly before shredding.

– When adding liquid through the feed tube, do so in a slow, steady stream.

– To remove food processed with the metal blade, remove the work bowl cover, then carefully remove the blade before emptying the bowl.

– Use a spatula to scrape the sides of the bowl as needed to ensure even processing.

For optimal performance of your CUISINART DLC-2009M, adhere to the following maximum load levels:

If your CUISINART DLC-2009M fails to start, check the following:

1. Ensure the unit is properly plugged into a functioning electrical outlet.

2. Make sure the work bowl is securely locked onto the motor base. The handle should be slightly left of center.

3. Confirm that the work bowl cover is securely locked onto the work bowl. The locking tab on the cover must be fully engaged with the locking post on the bowl’s rim.

4. Check if the large pusher is in the feed tube. Some models require the large pusher to be in place to activate the machine.

If the motor on your CUISINART DLC-2009M slows down, the load may be too large or too heavy. Turn the machine off, unplug it, and remove some of the food. Repack the remaining food and try processing again in smaller batches.

Uneven slicing can occur for a couple of reasons:

1. The food may not be packed properly in the feed tube. For consistent slices, ensure food is cut with flat ends and packed securely in the feed tube before processing.

2. The pressure on the pusher may be uneven. Apply steady, light pressure to the pusher as you guide the food through the feed tube.

This can happen when processing soft vegetables. To prevent this, process a hard vegetable, such as a carrot, immediately after processing the softer vegetable. The harder vegetable will help clear the disc.