CRES COR R171S1828 (01) PDF Document

The electrical specifications for the CRES COR R171S1828 are as follows:

The model number for your CRES COR R171S1828 is a basic model number. It may be followed by letters such as M, L, D or end with S, Z and/or CAN.

To install your CRES COR R171S1828, follow these steps:

1. Remove all packing material from inside the cabinet.

2. INSTALL ALL ANGLES BEFORE THE UNIT IS TURNED ON.

3. Allow enough clearance around the cabinet for air flow.

To operate your CRES COR R171S1828:

1. Plug the cord into a proper wall outlet.

2. Turn the power switch to “ON”. The light will come on and the compressor will start. Listen closely for the compressor; it will be slightly loud at first, then quiet down. If you do not hear the compressor running, turn the power switch to “OFF” right away and refer to the troubleshooting guide.

3. Pre-chill the cabinet for approximately 40 minutes or until the temperature reaches approximately 38°F. Then, load the food.

Important: DO NOT PUT HOT FOOD INTO THE COLD CABINET!

To shut the CRES COR R171S1828 off, turn the power switch to “OFF”.

To reverse the door hardware for opposite hand opening on your CRES COR R171S1828 (Single Door Cabinet ONLY), follow these steps:

1. Remove hinge covers with a screwdriver.

2. Open the door and lift it up to remove it from the cabinet.

3. Unscrew and re-mount the hinges and latch strike to the opposite sides of the cabinet.

4. Remove the door hinges and the door latch. Turn the hinges and handle over and remount them in the same holes.

5. Remove the plastic cam from each hinge, rotate the cam 180° with the “V” groove on the cam toward the inside of the cabinet. Reseat the cam into the hinge.

6. Plug all the extra holes with screws.

7. Put the door onto the cabinet and adjust as necessary.

8. Snap on the hinge covers.

Before cleaning your CRES COR R171S1828, please observe the following warnings:

1. Unplug the cord from the wall.

2. Do NOT hose the cabinet with water.

3. Do NOT get water into the bottom compartment.

4. Do NOT use abrasives or harsh chemicals.

Here are some cleaning hints for your CRES COR R171S1828:

• Wipe up spills as soon as possible.

• Clean regularly to avoid heavy dirt build-up.

• Use the mildest cleaning procedure that will do the job.

• Always rub in the direction of polish lines to avoid scratching the surface.

• Use only a soft cloth, sponge, fibrous brushes, plastic or stainless steel pads for cleaning and scouring.

• Rinse thoroughly with fresh water after every cleaning operation.

• Always wipe dry to avoid water marks.

For cleaning the stainless steel inside and outside of your CRES COR R171S1828, use the following guide:

*Mild detergents include soaps and non-abrasive cleaners.

The refrigerator is shipped fully charged. The service specifications are:

• The high-side pressure should be approximately 440 PSI.

• Low pressure should be approximately 162 PSI at 75° F (24° C) room temperature.

• The charge should be 18 ounces of R134a.

Service valves are located on the condenser/compressor assembly.

If the unit is plugged in, the switch is ON, and the power light is off, the probable cause is the power cord.

If the unit is plugged in, the switch is ON, and the compressor is off, the probable cause is that the power supply is down.

If the evaporator fan is on, the power light is on, but the compressor is off, the probable causes are:

• 3a. Thermostat defective

• 3b. Defective start relay (compressor)

If the compressor is on but the cabinet is not cooling, the probable causes are:

• 4a. Low charge

• 4b. Frost build-up on evaporator coil

• 4c. Evaporator fan defective

• 4d. Thermostat defective

If the compressor starts and stops and the cabinet is not cooling, the probable causes are:

• 5a. Low Charge

• 5b. Faulty start capacitor (compressor)

• 5c. Faulty start relay (compressor)

If you are experiencing a noisy compressor, the probable causes are:

• 6a. Low charge

• 6b. Defective

The thermostat on the CRES COR R171S1828 is pre-set at approximately 38°F (3.8°C). Temperature adjustment can only be made by a Service Agency.

The following are the 120V replacement part numbers for the CRES COR R171S1828: