CASIO CELVIANO AP-S200GB (01) PDF Document

To prepare the power supply for the CASIO CELVIANO AP-S200GB, use only the AC adaptor AD-E24250LW (JEITA standard with unified polarity plug) that comes with the digital piano. Use of other adaptors may cause malfunction or smoke.

Step 1. Connect the power cord to the AC adaptor.

Step 2. Connect the AC adaptor to the power supply terminal (DC 24V) on the bottom of the unit.

Step 3. Plug the power cord into a household wall outlet.

Step 4. Be sure to turn the power off before plugging or unplugging the adaptor. Always unplug the adaptor from the power outlet when the piano is not being used for a long period of time.

To turn on the CASIO CELVIANO AP-S200GB, press the Power button. Each touch button will blink while the instrument is starting up. When all buttons remain lit, the piano is ready for use. If the power does not come on after a light press, press the button firmly again.

To turn the power off, press and hold the Power button for approximately 2 seconds. Note that even when turned off, the piano remains in a standby mode with a small amount of current flow. Always disconnect the adaptor if a lightning strike is possible or for long periods of non-use.

To adjust the volume, use the volume knob located next to the Power button. Turning it towards MAX increases the sound level of the entire piano.

The CASIO CELVIANO AP-S200GB features an Auto Power Off function that automatically shuts down the instrument after approximately 20 minutes of inactivity to prevent unnecessary power consumption. If you need the piano to stay on during a concert or performance, you can disable this feature by following these steps:

Step 1. Hold down the FUNCTION button.

Step 2. Press the Bb0 key on the keyboard to toggle the setting between Enable and Disable.

The CASIO CELVIANO AP-S200GB has 18 built-in tones and one dedicated bass tone. You can select a tone using the following methods:

Method 1: Touch the GRAND PIANO button to immediately select the GRAND PIANO CONCERT tone.

Method 2: Hold down the GRAND PIANO button and press a key from G3 to C#5 to select a specific tone directly from the list.

Method 3: Hold down the GRAND PIANO button and press the B2 key to select the previous tone or the C3 key to select the next tone in the list.

The following table describes the primary grand piano tones available on the CASIO CELVIANO AP-S200GB:

The Layer function on the CASIO CELVIANO AP-S200GB allows you to sound two tones simultaneously. The first tone is the Upper1 part and the second is the Upper2 part.

Step 1. Hold down the GRAND PIANO button and press the C7 key to turn Layer on.

Step 2. To select the second tone (Upper2 part), hold down the GRAND PIANO button and press one of the G3 to C5 keys. Ensure Layer is set to On before doing this.

Step 3. To turn layering off, either repeat Step 1 or touch the GRAND PIANO button alone.

The Split function divides the CASIO CELVIANO AP-S200GB keyboard into a left (Lower) section for bass and a right (Upper1) section for another tone.

Step 1. Hold down the GRAND PIANO button and press the C#5 key (BASS).

Step 2. The left section will now play the BASS tone, while the right section will remain the previously selected tone.

Step 3. To cancel the split state, select a tone other than the BASS tone while holding the GRAND PIANO button.

The Duet function on the CASIO CELVIANO AP-S200GB allows two people to play in the same pitch range. The keyboard is split in the center, and both sides have the same Middle C position.

Step 1. Hold down the FUNCTION button and press the F2 key to cycle through Duet modes.

Step 2. Select between Off, On (standard duet), or Pan. In Pan mode, the left keyboard sound is output from the left speaker only, and the right keyboard sound from the right speaker only.

Step 3. In Duet mode, the left pedal acts as the damper for the left side, the right pedal for the right side, and the center pedal for both sides.

To start or stop the metronome on the CASIO CELVIANO AP-S200GB, touch the METRONOME button. To adjust the beat settings, hold down the METRONOME button and press one of the keys from C#3 to Bb3 according to this list:

C#3: Off (Only a click sounds on each beat)

D3: 1 (A bell tone sounds on each beat)

Eb3 to Bb3: 2 to 9 beats (A bell tone sounds on the first beat, clicks on the remaining beats)

You can set the tempo of the CASIO CELVIANO AP-S200GB between 20 and 255 beats per minute using these methods:

Numerical Entry: Hold the METRONOME button and use keys A0 to F#1 (acting as 0-9 keys) to enter the tempo value.

Manual Increment: Hold the METRONOME button and press B2 to decrease or C3 to increase the tempo by 1.

Tempo Markings: Hold the METRONOME button and press a key from C2 to Ab2 to select a preset marking (e.g., Largo at 46 bpm, Allegro at 132 bpm, or Presto at 184 bpm).

Tap Tempo: Hold the METRONOME button and tap the Bb2 key two or more times at the desired speed. The piano will set the tempo based on your taps.

The CASIO CELVIANO AP-S200GB includes effects to add reverberation or a spread sound effect.

Step 1. Touch the SOUND MODE button to toggle effects on and off. Indicators above the button show the current status of Hall Simulator/Reverb and Surround.

Step 2. To select a preset for Hall Simulator or Reverb, hold the SOUND MODE button and press a key from A0 to E1. Hall options include N.Y. Club, Opera Hall, Berlin Hall, and British Stadium. Reverb options include Room, Large Room, Hall, and Stadium.

Step 3. To adjust the depth of the effect, hold the SOUND MODE button and press D2 to decrease or Eb2 to increase depth for built-in sounds.

Touch Response changes the volume based on how hard you press the keys. To adjust this on the CASIO CELVIANO AP-S200GB, hold down the GRAND PIANO button and press one of the following keys:

Eb1: Off (Volume remains constant regardless of key speed)

E1: 1 (Light – easier to produce loud sounds)

F1: 2 (Medium Light)

F#1: 3 (Normal – standard setting)

G1: 4 (Medium Heavy)

Ab1: 5 (Heavy – more difficult to produce loud sounds)

Transpose allows you to raise or lower the overall pitch of the CASIO CELVIANO AP-S200GB in semitone steps (up to +/- 12 semitones).

Step 1. Hold down the GRAND PIANO button.

Step 2. Press the C#1 key to lower the pitch by one semitone or the D1 key to raise the pitch by one semitone.

Step 3. Press C#1 and D1 together to reset the pitch to the default setting (0).

The MIDI Recorder on the CASIO CELVIANO AP-S200GB records keyboard performances and pedal usage into the internal memory.

Step 1. Switch to MIDI Recorder by holding the FUNCTION button and pressing B3.

Step 2. Touch the REC button. It will blink red to indicate record standby.

Step 3. Start playing. Recording begins automatically, and the REC button will light up red.

Step 4. To stop recording, touch the REC button again. It will return to a white light.

Step 5. To play back your recording, touch the Play/Stop button.

Note: Only one song can be recorded at a time; a new recording will erase the previous one.

To record your performance as audio data (WAV format) on the CASIO CELVIANO AP-S200GB, you must use a USB flash drive.

Step 1. Switch to Audio Recorder by holding the FUNCTION button and pressing C4.

Step 2. Insert a formatted USB flash drive into the USB Type A port.

Step 3. Touch the REC button (it will blink red).

Step 4. Start playing. Recording will begin automatically. The maximum recording time is approximately 25 minutes per file.

Step 5. Touch the REC button to stop. The file is saved in the AUDIOREC folder on the USB drive as TAKE**.WAV.

Before using a new USB flash drive with the CASIO CELVIANO AP-S200GB, it should be formatted on the instrument. Formatting will delete all existing data on the drive.

Step 1. Insert the USB flash drive into the USB Type A port.

Step 2. Press and hold the FUNCTION button.

Step 3. Press the C2 key (Format). The right side of the beat indicator will blink.

Step 4. Press the C1 key (Execute) to start formatting. The indicators above SOUND MODE and Play/Stop will light up sequentially.

Step 5. Release the FUNCTION button once formatting begins. Do not remove the drive until the process is complete.

You can play sound from a smart device through the speakers of the CASIO CELVIANO AP-S200GB using the supplied Wireless MIDI and audio adaptor.

Step 1. Insert the wireless adaptor into the USB Type A port.

Step 2. Ensure the piano’s wireless function is On (Hold FUNCTION and press D1 if needed).

Step 3. Hold down the FUNCTION button and press the C#1 key (Wireless Audio Pairing). The Power button will flash blue.

Step 4. On your smart device, select “WU-BT10 AUDIO” in the Bluetooth settings to pair. When connected, the piano will sound a notification tone and the Power button will light up blue.

A factory reset returns all settings of the CASIO CELVIANO AP-S200GB to their original factory defaults.

Step 1. Press and hold the FUNCTION button.

Step 2. Press the A0 key (Factory Reset). The FUNCTION button will start blinking.

Step 3. Press the C1 key (Execute) to start the initialization. Processing may take some time.

Step 4. Once complete, all touch buttons on the panel will light up.

If you encounter no sound on the CASIO CELVIANO AP-S200GB, check the following causes and solutions:

Cause 1: The volume is turned down. Solution: Turn the volume knob towards MAX.

Cause 2: Headphones or a conversion plug are connected. Solution: Unplug them from the PHONES/OUTPUT jacks.

Cause 3: Local Control is set to Off. Solution: Hold FUNCTION and press F6 to turn Local Control On.

Cause 4: Speaker Out is set to Off. Solution: Hold FUNCTION and press Eb7 to set Speaker Out to Auto or On.

On the CASIO CELVIANO AP-S200GB, you can adjust specific volumes relative to the overall volume:

Keyboard Volume: Hold FUNCTION and press G3 to lower or Ab3 to raise keyboard volume.

MIDI Song Volume: Hold FUNCTION and press F3 to lower or F#3 to raise the volume of MIDI songs.

Audio Song Volume: Hold FUNCTION and press D3 to lower or Eb3 to raise the volume of audio files on a USB drive.

Wireless Audio Volume: Hold FUNCTION and press B2 to lower or C3 to raise the volume of audio coming via Bluetooth.